M20 Head Removal

Need technical Q/A then you're in the right place

Moderator: martauto

capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Sat Jan 07, 2012 6:37 pm

I need to change the headgasket on my turd to cure the standard front of head oil leak and sort a number of broken exhaust manifold studs.

The car currently starts and runs nicely with no issues and no smoke.

Much as I would like to do a full refresh -new followers, valve seals & guides, spray bar, pressure test, skim etc whilst its off I'm a bit short on cash so could do without the several hundred quid this is bound to cost by the time everythings been taken into consideration - for starters I understand a genuine headgasket alone is the thick end of £100 without any of the other gaskets needed to complete the job.

So - when a head is removed is it always necessary to get it skimmed ? Or pressure tested ( when it shows no signs of any issues ) ?

Or is it just a case of whip it off, swap the gasket and put it back on ?

I have very painful experience of E30 "while its in bits you may as well......" jobs so could really do without a massive cash outlay on whilst you're at it jobs - but in this case the only bits that are actually knackered are the gasket and manifold studs.

I already have a water pump and cambelt/tensioner to go on as part of the job so no probs there.

Do M20 heads have valve stem oil seals which can be replaced with the head in-situ at a later date if necessary ?

:)
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
chh137
E30 Zone Squatter
E30 Zone Squatter
Posts: 1502
Joined: Mon Apr 18, 2011 11:00 pm
Location: deepest darkest derbyshire

Post Sat Jan 07, 2012 6:50 pm

My old dad always said "if ajobs worth doing its worth doing well"
Full gasket set inc stem seals ,reseat/grind in valves etc and head test + skim or you may end up doing it all again 6 months down the road.
In other words all or nothing & put up with oil leak
Last edited by chh137 on Sat Jan 07, 2012 7:51 pm, edited 1 time in total.
lyricalnut02
E30 Zone Regular
E30 Zone Regular
Posts: 846
Joined: Fri Nov 23, 2007 11:00 pm
Location: London

Post Sat Jan 07, 2012 7:45 pm

got to agree with that ^
325i Sport Tech 1 - R.I.P

E30 addict.
CHR1S1990
E30 Zone Camper
E30 Zone Camper
Posts: 1121
Joined: Fri Mar 14, 2008 11:00 pm
Location: Blackpool

Post Sat Jan 07, 2012 7:56 pm

i have to totally disagree. There's no point in shelling out lots of cash when there isnt anything wrong. Dont fix it if is aint broken springs to mind?

I had a headgasket job a while back. HG itself failed due to age, not over heating (water was mixing into oil and bores). Whipped the head off, changed the HG with a victor reinz one (OEM AFAIK and no where near dealer £100 from euro's) and obviously a new set of head bolts, also VR. Checked the head on a piece of thick glass, also used a steel rule. No need for skim or pressure test if you havent overheated and warped/cracked anything.
Image
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Sat Jan 07, 2012 8:06 pm

CHR1S1990 wrote:i have to totally disagree. There's no point in shelling out lots of cash when there isnt anything wrong. Dont fix it if is aint broken springs to mind?

I had a headgasket job a while back. HG itself failed due to age, not over heating (water was mixing into oil and bores). Whipped the head off, changed the HG with a victor reinz one (OEM AFAIK and no where near dealer £100 from euro's) and obviously a new set of head bolts, also VR. Checked the head on a piece of thick glass, also used a steel rule. No need for skim or pressure test if you havent overheated and warped/cracked anything.
+1 ive changed many many ali heads on many different types of engines a quick check over and not one has ever failed
i cant see where this gotta skim a head when its off came from ok if you cooked it fair enough but most of the time there fine
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
steve_k
E30 Zone Team Member
E30 Zone Team Member
Posts: 8044
Joined: Fri May 23, 2008 11:00 pm
Location: in the vale of mansfield

Post Sat Jan 07, 2012 8:11 pm

CHR1S1990 wrote:i have to totally disagree. There's no point in shelling out lots of cash when there isnt anything wrong. Dont fix it if is aint broken springs to mind?

I had a headgasket job a while back. HG itself failed due to age, not over heating (water was mixing into oil and bores). Whipped the head off, changed the HG with a victor reinz one (OEM AFAIK and no where near dealer £100 from euro's) and obviously a new set of head bolts, also VR. Checked the head on a piece of thick glass, also used a steel rule. No need for skim or pressure test if you havent overheated and warped/cracked anything.
so whats the best way to visually inspect the head?
got a spare one i'm going to rebuild soon & i normally send them off to be pressure tested/skimmed,

the spare was taken off when i had another rebuilt with a 274dg cam & the gararge (local bmw experts) said that there where no signs of it over heating.

round here a skim & pressure test costs about £70. sometimes it's better to be on the safe side i guess.
if it's got t*ts or wheels it's bound to be trouble...............prove me wrong.
getting oral sex off an ugly person is like rock climbing.....don't look down ;)
chh137
E30 Zone Squatter
E30 Zone Squatter
Posts: 1502
Joined: Mon Apr 18, 2011 11:00 pm
Location: deepest darkest derbyshire

Post Sat Jan 07, 2012 8:20 pm

No need for skim or pressure test if you havent overheated and warped/cracked anything.[/quote]

Can warp/crack on removal. Particularly if correct removal procedure is not observed.
Good PROVEN engineering practice also sets the precedence.
CHR1S1990
E30 Zone Camper
E30 Zone Camper
Posts: 1121
Joined: Fri Mar 14, 2008 11:00 pm
Location: Blackpool

Post Sat Jan 07, 2012 8:27 pm

more to the point, your head would be getting quite thin if you keep skimming it regardless.

you could use a steel rule and some feeler gauges. You could even place it on the block (with no HG) and use feeler gauges, cast iron rarely warps.

to the above, only a dumbass would remove a head when warm leading to warping :mad:

I would only fork out £70 for a skim/pressure test in 3 instances. A) I had the money to just thrown at it, B) Its quite possible that it is warped/cracked as I have overheated the engine and/or its losing water, C) I bought one off someone else without knowing it's full history.
Image
chh137
E30 Zone Squatter
E30 Zone Squatter
Posts: 1502
Joined: Mon Apr 18, 2011 11:00 pm
Location: deepest darkest derbyshire

Post Sat Jan 07, 2012 8:33 pm

Who said anything about head being warm?
As for head" getting thin" how much do you think is m/c off?
Again good PROVEN engeering practice.
CHR1S1990
E30 Zone Camper
E30 Zone Camper
Posts: 1121
Joined: Fri Mar 14, 2008 11:00 pm
Location: Blackpool

Post Sat Jan 07, 2012 8:39 pm

why would a perfectly "straight" cold head warp when removed from a cold block? You said a head can warp/crack on removal. Particularly if correct removal procedure is not observed. Only incorrect procedure I can see (other than being a tool and physically damaging the head) is removing the head whilst the engine is still warm.
Image
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Sat Jan 07, 2012 8:47 pm

they machine of as much as nessacery to make it flat cold be 10 tho could be 50 tho thats if it is warped
like chris said a good straight metal rule or some thing that is known to be flat eg a piece of glass or an engineering plate with feelers should be fine not to mention every time it has a skim your compression goes up every time
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
chh137
E30 Zone Squatter
E30 Zone Squatter
Posts: 1502
Joined: Mon Apr 18, 2011 11:00 pm
Location: deepest darkest derbyshire

Post Sat Jan 07, 2012 8:49 pm

incorrect order of removal of head bolts may cause warp or twist .
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Sat Jan 07, 2012 8:51 pm

chh137 wrote:incorrect order of removal of head bolts may cause warp or twist .
only if warm tho

stone cold shouldnt matter but should always follow correct head bolt removal
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
B7
E30 Zone Team Member
E30 Zone Team Member
Posts: 15841
Joined: Tue Feb 13, 2007 11:00 pm
Location: Surrey / West Sussex

Post Sat Jan 07, 2012 8:52 pm

Rob. If you buy the OEM gasket set from GSF or ECP, I believe the valve stem oil seals come with it. OR if you buy the gasket alone, there are loads of M20 gasket tiop end sets on the bay for 30 odd quid c/w stem seals. It matters not if the head gasket is of top quality. At least you get all new inlet gaskets, exhaust gaskets as well.

http://www.ebay.co.uk/itm/BMW-325i-525i ... 1c069954f2

personally I would always change the valve seals, lap the valves in to a nice finish and have the head "faced" off to clean the surface ready for the new gasket. If it ain't overheating then the pressure test is not essential really.

That oil leak is easily cured once and for all with a touch of a product that Si13 got recommended by Demlot. Can't remember it's name but drop Si a line.
B7's Motto. "If it's French, BURN IT!!!!!!"
CHR1S1990
E30 Zone Camper
E30 Zone Camper
Posts: 1121
Joined: Fri Mar 14, 2008 11:00 pm
Location: Blackpool

Post Sat Jan 07, 2012 8:53 pm

you obviously arent reading my threads properly.

"your head would be getting quite thin if you keep skimming it regardless. " which is surely the point were arguing about? skimming the head just because "its good practice"?

whos to say the head hasnt been skimmed before?
Image
User avatar
Tay
E30 Zone Regular
E30 Zone Regular
Posts: 343
Joined: Mon Feb 06, 2006 11:00 pm

Post Sat Jan 07, 2012 8:58 pm

as a BMW specialist for many years, with the good old M20 engine, if your going to take the head off......

get a head set from euro a reinz or elring both exactly the same as the bmw part and about £80

if you get that then you may as well take the rocker shafts out and cam, quickly lap the valves in by hand, and replace the stem seals as this is near impossible while the head is on on the bottom end.

while the cam is out look along the length of the head where it runs and look for any sign of a crack quite obvious if it has.

as for skimming i always skim a head before i refit just so i can guarentee a perfect seal once she's bolted back down, however if you deam that it is flat using a straight edge and it has no corrosion around the waterways then bolt her straight back on!!!

i wouldn't worry about new head bolts they never stretch and the only head bolts that i've ever replaced is when i had the priveledge of dooing a rover 'k' series head!!!!!

the head set will give you all the seals and gaskets that you need to replace everything on the head. however if your only going to get the head gasket then i would look for a reinz or elring again and wouldn't be looking at spending any more than about £40+ the obvious.

on a plus note i've never cracked or bent a head through removal or refit!!!!

have fun or bring her down to somerset and i'll sort her for you cheap!!!!
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Sat Jan 07, 2012 8:59 pm

chh137 wrote:Who said anything about head being warm?
As for head" getting thin" how much do you think is m/c off?
Again good PROVEN engeering practice.
as i said before ive been messing around with engines since i was about 6 im a trained engineer cnc precision i can build an engine with my eyes shut so i know about tolerences etc and not once have i ever had a head skimmed when doing a head gasket and it fail the only head ive ever had skimmed is on my current one as i had the water ways welded
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
chh137
E30 Zone Squatter
E30 Zone Squatter
Posts: 1502
Joined: Mon Apr 18, 2011 11:00 pm
Location: deepest darkest derbyshire

Post Sat Jan 07, 2012 9:09 pm

Normally and on most engines head gasket would only be replaced once or maybe twice in life of said engine.thats if its done right first time.
Should only be 5 to 10 thou per skim so compression ratio is hardly affected/some manufaturers supply thicker gaskets for this purpose.
Anyway enough now . we all have different opinions and i was only passing on my advice born out by experience.
CHR1S1990
E30 Zone Camper
E30 Zone Camper
Posts: 1121
Joined: Fri Mar 14, 2008 11:00 pm
Location: Blackpool

Post Sat Jan 07, 2012 9:12 pm

Tay wrote:i wouldn't worry about new head bolts they never stretch and the only head bolts that i've ever replaced is when i had the priveledge of dooing a rover 'k' series head!!!!!
headbolts are stretch (torx) and should be replaced with new
Image
User avatar
Tay
E30 Zone Regular
E30 Zone Regular
Posts: 343
Joined: Mon Feb 06, 2006 11:00 pm

Post Sat Jan 07, 2012 9:23 pm

never replaced a bm headbolt i could pull the ones out of my engine and mic them up and there would be no difference at all. and that would the then they would be fitted for the 3rd time, bearing in mind that i found the engine in a hedge at the garage so took the top off to check the internals weren't rusted up not because of any head problems.

everyone worries too much about headbolts because thats what garages preach about same as the pattern for torquing and the 90 then 90 again no need 55ftlb all round is plenty good enough.

and if your worried about head bolts then you won't like the fact that i haven't torqued a head down since i first learnt mechanics, i can pull a head bolt down to over 70ftlb with a 3/8 rachet.....................
bss325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 24532
Joined: Sat Jan 20, 2007 11:00 pm
Location: London/Surrey

Post Sat Jan 07, 2012 10:15 pm

Some interesting views in this thread.
http://www.bmrperformance.co.uk

BMW and MINI specialist - Gatwick
TPS
E30 Zone Team Member
E30 Zone Team Member
Posts: 13119
Joined: Fri Mar 06, 2009 11:00 pm
Location: Hampshire

Post Sat Jan 07, 2012 10:20 pm

I would personally replace Head Bolts everytime, Can't be too careful!
Image
1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
CHR1S1990
E30 Zone Camper
E30 Zone Camper
Posts: 1121
Joined: Fri Mar 14, 2008 11:00 pm
Location: Blackpool

Post Sun Jan 08, 2012 12:21 am

Tay wrote:never replaced a bm headbolt i could pull the ones out of my engine and mic them up and there would be no difference at all. and that would the then they would be fitted for the 3rd time, bearing in mind that i found the engine in a hedge at the garage so took the top off to check the internals weren't rusted up not because of any head problems.

everyone worries too much about headbolts because thats what garages preach about same as the pattern for torquing and the 90 then 90 again no need 55ftlb all round is plenty good enough.

and if your worried about head bolts then you won't like the fact that i haven't torqued a head down since i first learnt mechanics, i can pull a head bolt down to over 70ftlb with a 3/8 rachet.....................
youve obviously got a lot more experience in this than I, but i can't see logically how your heads have been staying put using these methods taking into consideration how stretch bolts actually work (assuming you are actually using the bmw-replaced torx head bolts).

have a read here if anyone is interested

http://www.unofficialbmw.com/all/engine ... bolts.html

"The replacement bolts your dealer supplied are referred to as s-t-r-e-t-c-h bolts, because they are PERMANENTLY stretched when properly installed. When stretched they actually "neck down" or have a reduced diameter and area where the metal has been stretched. This reduced area has experienced Plastic Deformation, and will not hold the same torque (tension) if applied again, it will in fact stretch more, (loosing tension) and often fracture. This is why stretch bolts must ALWAYS be replaced, and never reused."

This would suggest that applying your 55ftlb more than once to your bolts is impossible to provide enough clamping force to keep the head down.
Image
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Sun Jan 08, 2012 8:26 am

Wow lots of different opinions ! Thanks for the input.

I already have a pair of genuine Exhaust manifold gaskets to go on which I bought ages ago before I realised how many studs were bust :x

The question regarding pressure testing & skimming was one of the main things I wanted clarification on as the majority of threads I see on this subject seem to suggest its standard practice - however as the car doesnt overheat I have no reason to believe the head would be warped or cracked hence the question can I just swap the gasket without touching the rest of it.

I would change the head bolts regardless.

Following simon13's build thread I'm also pretty sure I'll be fitting a genuine Head Gasket.

Where I start to get twitchy is pulling the top end apart - removing rocker shafts and followers, replacing stem seals ( Are these the same as "valve guides" ? ) lapping the valves in, and then rebuilding it all and setting it all back up.

I'm not an engineer - whilst I can pull something apart and put it back together given time I just don't have the "feel" for things like lapping in valves and setting the valve clearances - plus I'd be worried about putting it back together wrong and fecking it up.
I would expect you need a special tool to compress the valve springs to change the stem seals ? - Which I don't have.

Can anyone give a ballpark figure for labour cost if I give an engineering firm the head as it is when removed from the car, a set of valve seals and manifold studs and tell them to get on with it ? - I think there are about 4 broken exhaust manifold studs which will need removing plus a basic check for flatness and a reface assuming it doesnt need a skim.

Just trying to keep in mind that the ONLY reasons for removing the head are the oil leak and broken manifold studs. I don't really want to turn a £200 job into a £600 job which is normally the way these things seem to go :evil:

Cheers people.
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Sun Jan 08, 2012 8:34 am

valve stem seals are the little rubber and steel cup that push on top of the valve guide the valve guide is the bronze bit that the valve slides up and down in obviously the seal just stops oil leaking down the valve stem
taking the head apart is an easy job I think you'll enjoy it
if I was any nearer I would come and do it for ya

but cost I wouldn't know as I do it all my self but if you need and help I'm more than willing to give you my number and talk you tho it :)
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Sun Jan 08, 2012 9:55 am

i think rob tbh your gonna find wear on the rockers and cam. Its almost inevitable on the milege.

As said if you remove the head bolts in the right sequence you can just have it refaced and don't bother with a pressure test.

Why don't you just leave it for now? it won't get anyworse than it is. And all 325's are like this! One good tip is the reason the studs on the exhuast break is becasue the log manifold bows with time. This puts sidways pressure on the studs and hey presto........

Any how might point is get the log refaced flat if its like a banana
User avatar
Tay
E30 Zone Regular
E30 Zone Regular
Posts: 343
Joined: Mon Feb 06, 2006 11:00 pm

Post Sun Jan 08, 2012 10:04 am

Headbolts or no Headbolts, my years of experience has proved to me they are in needed!!!!

Anyways, it's an easy job to do the head yourself and if it's off you may as well do the internal parts. You must know someone with a spring compressor??? As long as you put all the valves back in the correct cylinder and the rocker shafts in the right places so the Headbolts can pass past them you won't be far out! And have a play with the clearances which should be 10thou no more no less with the loab of the cam shaft fully down.

55ftlb isn't a great deal of torque and your head bolts will easily take that! No point in the 90 and 90 again

And remember there is a massive difference between a mechanic and an engineer!

If you was to pay someone to do the head for you expect to pay from 200 up I myself would do the whole thing for 250 including removal and refit! You just need to fit a sensibly priced mechanic, the back street guys tend to be cheaper and most of the time have alot more experience!
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Sun Jan 08, 2012 10:13 am

10 tho with the lobes down ?????
I doubt it

More like 25 tho cold with the lobe fully up the valve has to be completely closed to do valve clearances
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Sun Jan 08, 2012 10:21 am

i'd ignore Tays comment. lots of errors without trying to sound harsh
User avatar
Tay
E30 Zone Regular
E30 Zone Regular
Posts: 343
Joined: Mon Feb 06, 2006 11:00 pm

Post Sun Jan 08, 2012 10:28 am

on a M20 engine the lobes need to be down as the rockers operate from above the cam shaft???? if the lobe was to be up then the valve would be fully open. 10 thou is the perfect clearance which will give you the optimum performance with 25thou clearance the engine would be too rattley and wouldn't perform properly.

ok you may not like my methods with headbolts but with well over a decade of experience as a bmw specialist and 100's of engines fully rebuilt, i know what works and what has worked for me???
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Sun Jan 08, 2012 10:31 am

Tay wrote:on a M20 engine the lobes need to be down as the rockers operate from above the cam shaft???? if the lobe was to be up then the valve would be fully open. 10 thou is the perfect clearance which will give you the optimum performance with 25thou clearance the engine would be too rattley and wouldn't perform properly.

ok you may not like my methods with headbolts but with well over a decade of experience as a bmw specialist and 100's of engines fully rebuilt, i know what works and what has worked for me???
Sorry my mistake I was totally wrong there dunno what I was thinking there it's early I ain't been up long lol

But cold they are meant to be .25 from cold that's the bently and Haynes manual recommendations
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
User avatar
Tay
E30 Zone Regular
E30 Zone Regular
Posts: 343
Joined: Mon Feb 06, 2006 11:00 pm

Post Sun Jan 08, 2012 10:41 am

arrrrr is that .25 metric????? i think that and 10thou are the same??? but i have never been that great with conversion charts!!! and always have a feeler gauge marked so i know which one it is!!!!!

i think in your early morning slumber you were dreaming about the little M40 with it's followers!!!!
ross2009
E30 Zone Addict
E30 Zone Addict
Posts: 2762
Joined: Mon Nov 19, 2007 11:00 pm
Location: In my beemer MAN !!!! st neots CAMBS

Post Sun Jan 08, 2012 10:44 am

Lol yeah I think your rit 10 tho is near on .25 lol
Turbo M20
Image
v8 project 6.0 twin turbo
http://s924.photobucket.com/user/Rossco ... ject%20e30
penton08
E30 Zone Camper
E30 Zone Camper
Posts: 1206
Joined: Sat May 10, 2008 11:00 pm

Post Sun Jan 08, 2012 10:44 am

A full on head refurb (new guides, seals, skim, studs, seats, ect) at a engineering shop will cost £400 upwards! As for putting a head back on, new bolts and a re face every time imo.
User avatar
Tay
E30 Zone Regular
E30 Zone Regular
Posts: 343
Joined: Mon Feb 06, 2006 11:00 pm

Post Sun Jan 08, 2012 10:55 am

ross2009 thank christ we've got that cleared up, without making me look like a total idiot!!! lol

guides and seats is the last thing thar i would do, they never get them right and they tend not to be worn, however if they are then dig out and get them changed, however with the seats you want the seat to be as narrow as possible, and all the seats that i've seen recut the seats tend to be quite thick!