Moving fuse box tiop tips pelase!

Need technical Q/A then you're in the right place

Moderator: martauto

milescook
E30 Zone Camper
E30 Zone Camper
Posts: 1285
Joined: Thu Jan 13, 2011 11:00 pm
Location: The 'bran of Cwm

Post Thu Jan 05, 2012 11:32 am

The car is going in for a roll cage Monday that goes to the front struts. I'll be getting a smaller batter but the fuse box presumably needs to move.

Any tips on this madness? Would it bea easier to move it inside? There's a lot of wires to cut, strip, lenghten, put back together again :( Would I be okay joining them and sealing with heat shrink?

Thanks a million- not looking forward to this so all advice greatfuly appreciated!
The story so far... http://www.cookracing.co.uk/

Also please help the race budget by watching some videos :) https://www.youtube.com/cookracinguk
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Thu Jan 05, 2012 11:35 am

If you undo the brake servo and all of the chassis harness in the engine bay you can swing the fuse box half way down the turret, thats plenty of space!

I would not under any circumstances cut any wires or even consider you are able to put things back together again with some heat shrink!

Andrew
milescook
E30 Zone Camper
E30 Zone Camper
Posts: 1285
Joined: Thu Jan 13, 2011 11:00 pm
Location: The 'bran of Cwm

Post Thu Jan 05, 2012 11:42 am

Oh jesus that sounds a lot of work :( Cheers for the advice on not cutting though! Any more?
The story so far... http://www.cookracing.co.uk/

Also please help the race budget by watching some videos :) https://www.youtube.com/cookracinguk
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Thu Jan 05, 2012 1:03 pm

If it's going to be stripped, then you can undo all the connections and pull the loom out through the bulkhead into the engine bay. But there's no way to relocate the fuse box any more than about six inches from where it currently sits, without massive surgery to the wires, which really isn't recommended.

A little more info can be read here:

http://www.e30zone.net/e30zonewiki/index.php/Loom
milescook
E30 Zone Camper
E30 Zone Camper
Posts: 1285
Joined: Thu Jan 13, 2011 11:00 pm
Location: The 'bran of Cwm

Post Fri Jan 06, 2012 6:42 pm

Cheers I've been able to move it enough out the way of where will go roll cage strut to turret.can't see it fitting halfway down turret? Theres fluid bottle in way.might be able to bolt it in further towards centre after cage is in will post back!
Cheers.
The story so far... http://www.cookracing.co.uk/

Also please help the race budget by watching some videos :) https://www.youtube.com/cookracinguk
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Fri Jan 06, 2012 7:03 pm

Usual way is remove the whole loom through the hole in the bulkhead then refit it from inside the car with the fusebox mounted in the glovebox area. Lot of faff but gives a clean/tidy engine bay afterwards
milescook
E30 Zone Camper
E30 Zone Camper
Posts: 1285
Joined: Thu Jan 13, 2011 11:00 pm
Location: The 'bran of Cwm

Post Fri Jan 06, 2012 7:16 pm

Cheers.id have to lengthen some wiring though theres a few looms feeding off that.lengthening a bad idea?
The story so far... http://www.cookracing.co.uk/

Also please help the race budget by watching some videos :) https://www.youtube.com/cookracinguk