Hi guys I'm currently looking at a scrap e30 316 on carbs.
And it has power steering I've removed the rack, pump and bracket, pipes and res bottle.
Do I need the crank pulley ? Mine is a single v This one has a three v pulley.
But problem is its seized on , do I need this or can I get a long belt for my single pulley to go around the fan , alt then pump ?
Cheers !
urgent power steering help before I leave scrappers
Moderator: martauto
-
Brian28
- E30 Zone Squatter

- Posts: 1596
- Joined: Sat Jun 11, 2005 11:00 pm
- Location: Bournemouth
You need the pulley as the alignemnt is different, also the alloy bracket that the alternator is mounted to as it's different with ps. When the 13mm bolts are off the pulley usually comes off handy enough with a couple of taps from the whacking stick. Try hitting it inwards as well to break any rust seal.
Edit - Sorry the above is for a 6 pot, but chances are they are the same as 4 pot.
Edit - Sorry the above is for a 6 pot, but chances are they are the same as 4 pot.
For sale - E30 320i racer project - sold.
-
gazwhittle
- E30 Zone Newbie

- Posts: 181
- Joined: Wed Nov 23, 2011 11:00 pm
I didn't get that far mate, I couldn't get the 30mm nut off after removing most of the front end and dropping the engine down a little.
I think I might get him to pull the engine for me so I can get it off with an impact gun
Bracket fits on my m10 perfect just need to get a rack and pulley and I'm done
I think I might get him to pull the engine for me so I can get it off with an impact gun
Bracket fits on my m10 perfect just need to get a rack and pulley and I'm done
-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
Pulley shouldnt be held on with the big nut, about 8 13mm bolts hold it on.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
rix313
- E30 Zone Team Member

- Posts: 4970
- Joined: Fri Oct 31, 2008 11:00 pm
- Location: Silverstone
It's done up to around 300ft/lb iirc so you won't be getting that sucker undone easily. As Lee says, there are 6 M8 bolts which hold the pulleys on.gazwhittle wrote: I couldn't get the 30mm nut off
-
gazwhittle
- E30 Zone Newbie

- Posts: 181
- Joined: Wed Nov 23, 2011 11:00 pm
Are you sure ? I had a good look and could only see the 30mm nut ? If there are m8 bolts will undoing these get the pulley off ? Or will the 30mm one need removing
-
suedenim
- E30 Zone Regular

- Posts: 788
- Joined: Mon Nov 08, 2010 11:00 pm
- Location: London
With a nut torqued that high you want the biggest size drive you've got 3/4" drive/socket would be ideal. Leverage is your friend! You'll need a long breaker bar or a snug fitting pipe with decent wall thickness as an extension.rix313 wrote:It's done up to around 300ft/lb iirc so you won't be getting that sucker undone easily. As Lee says, there are 6 M8 bolts which hold the pulleys on.gazwhittle wrote: I couldn't get the 30mm nut off
Good luck!
1982 E21 316 Baltic Blau
1989 318i 2 Door Sterling Silber
Feedback: http://www.e30zone.net/modules.php?name ... highlight=
1989 318i 2 Door Sterling Silber
Feedback: http://www.e30zone.net/modules.php?name ... highlight=
-
gazwhittle
- E30 Zone Newbie

- Posts: 181
- Joined: Wed Nov 23, 2011 11:00 pm
and im right in thinking it turns counter clockwise?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Don't think the M10 has a crank pulley that's made up of bolt together bits, like the M20 or M40.
A M10 with aircon and/or power steering uses a complete different front pulley.
Bolt is normal thread.
The best way to undo it is to place ring spanner on the bolt, connect up a good battery, and 'hot wire' the starter motor, preferably from inside the car (in the interests of safety).
The spanner should hit the chassis member with enough force to loosen the bolt.
A M10 with aircon and/or power steering uses a complete different front pulley.
Bolt is normal thread.
The best way to undo it is to place ring spanner on the bolt, connect up a good battery, and 'hot wire' the starter motor, preferably from inside the car (in the interests of safety).
The spanner should hit the chassis member with enough force to loosen the bolt.
-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
You will need the 'UJ' that connects the steering coloum to the rack. IIRC power steering ones are slightly shorter
E30 Crazy!
-
gazwhittle
- E30 Zone Newbie

- Posts: 181
- Joined: Wed Nov 23, 2011 11:00 pm
well good news i pissed the pulley bolt off using my 1.5meter bar off my 3ton jack.
and he only charged me a tenner for that and the steering rack uj.
but the bush is fcuked on it
and im guessing by the rivets it cant be changed?
and he only charged me a tenner for that and the steering rack uj.
but the bush is fcuked on it
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
No problem changing it. Grind off the rivets, and use the special shouldered bolts that BMW supply, along with nyloc nuts and washers to replace them.gazwhittle wrote:
but the bush is fcuked on itand im guessing by the rivets it cant be changed?
http://bmwfans.info/parts/catalog/E30/2 ... _assembly/
you need a #3 and four of #6.
-
gazwhittle
- E30 Zone Newbie

- Posts: 181
- Joined: Wed Nov 23, 2011 11:00 pm
sweet cheers dude ill ring bmw in the morn!Brianmoooore wrote:No problem changing it. Grind off the rivets, and use the special shouldered bolts that BMW supply, along with nyloc nuts and washers to replace them.gazwhittle wrote:
but the bush is fcuked on itand im guessing by the rivets it cant be changed?
http://bmwfans.info/parts/catalog/E30/2 ... _assembly/
you need a #3 and four of #6.
