urgent power steering help before I leave scrappers

Need technical Q/A then you're in the right place

Moderator: martauto

gazwhittle
E30 Zone Newbie
E30 Zone Newbie
Posts: 181
Joined: Wed Nov 23, 2011 11:00 pm

Post Sun Dec 18, 2011 1:57 pm

Hi guys I'm currently looking at a scrap e30 316 on carbs.

And it has power steering I've removed the rack, pump and bracket, pipes and res bottle.

Do I need the crank pulley ? Mine is a single v This one has a three v pulley.


But problem is its seized on , do I need this or can I get a long belt for my single pulley to go around the fan , alt then pump ?

Cheers !
User avatar
Brian28
E30 Zone Squatter
E30 Zone Squatter
Posts: 1596
Joined: Sat Jun 11, 2005 11:00 pm
Location: Bournemouth

Post Sun Dec 18, 2011 2:08 pm

You need the pulley as the alignemnt is different, also the alloy bracket that the alternator is mounted to as it's different with ps. When the 13mm bolts are off the pulley usually comes off handy enough with a couple of taps from the whacking stick. Try hitting it inwards as well to break any rust seal.

Edit - Sorry the above is for a 6 pot, but chances are they are the same as 4 pot.
For sale - E30 320i racer project - sold.
gazwhittle
E30 Zone Newbie
E30 Zone Newbie
Posts: 181
Joined: Wed Nov 23, 2011 11:00 pm

Post Sun Dec 18, 2011 3:41 pm

I didn't get that far mate, I couldn't get the 30mm nut off after removing most of the front end and dropping the engine down a little.

I think I might get him to pull the engine for me so I can get it off with an impact gun

Bracket fits on my m10 perfect just need to get a rack and pulley and I'm done
leeparkes
Married to the E30 Zone
Married to the E30 Zone
Posts: 9535
Joined: Thu Jan 03, 2008 11:00 pm
Location: Black country

Post Sun Dec 18, 2011 3:57 pm

Pulley shouldnt be held on with the big nut, about 8 13mm bolts hold it on.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place.. :o:
rix313
E30 Zone Team Member
E30 Zone Team Member
Posts: 4970
Joined: Fri Oct 31, 2008 11:00 pm
Location: Silverstone

Post Sun Dec 18, 2011 4:05 pm

gazwhittle wrote: I couldn't get the 30mm nut off
It's done up to around 300ft/lb iirc so you won't be getting that sucker undone easily. As Lee says, there are 6 M8 bolts which hold the pulleys on.
gazwhittle
E30 Zone Newbie
E30 Zone Newbie
Posts: 181
Joined: Wed Nov 23, 2011 11:00 pm

Post Sun Dec 18, 2011 4:09 pm

Are you sure ? I had a good look and could only see the 30mm nut ? If there are m8 bolts will undoing these get the pulley off ? Or will the 30mm one need removing
suedenim
E30 Zone Regular
E30 Zone Regular
Posts: 788
Joined: Mon Nov 08, 2010 11:00 pm
Location: London

Post Sun Dec 18, 2011 5:01 pm

rix313 wrote:
gazwhittle wrote: I couldn't get the 30mm nut off
It's done up to around 300ft/lb iirc so you won't be getting that sucker undone easily. As Lee says, there are 6 M8 bolts which hold the pulleys on.
With a nut torqued that high you want the biggest size drive you've got 3/4" drive/socket would be ideal. Leverage is your friend! You'll need a long breaker bar or a snug fitting pipe with decent wall thickness as an extension.

Good luck!
1982 E21 316 Baltic Blau
1989 318i 2 Door Sterling Silber

Feedback: http://www.e30zone.net/modules.php?name ... highlight=
gazwhittle
E30 Zone Newbie
E30 Zone Newbie
Posts: 181
Joined: Wed Nov 23, 2011 11:00 pm

Post Sun Dec 18, 2011 9:11 pm

and im right in thinking it turns counter clockwise?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Dec 18, 2011 9:36 pm

Don't think the M10 has a crank pulley that's made up of bolt together bits, like the M20 or M40.
A M10 with aircon and/or power steering uses a complete different front pulley.
Bolt is normal thread.
The best way to undo it is to place ring spanner on the bolt, connect up a good battery, and 'hot wire' the starter motor, preferably from inside the car (in the interests of safety).
The spanner should hit the chassis member with enough force to loosen the bolt.
Ajsingh
E30 Zone Addict
E30 Zone Addict
Posts: 2378
Joined: Sun Mar 28, 2010 11:00 pm
Location: West Laaaandaan init! / Milton Keynes

Post Mon Dec 19, 2011 7:00 am

You will need the 'UJ' that connects the steering coloum to the rack. IIRC power steering ones are slightly shorter
E30 Crazy!
gazwhittle
E30 Zone Newbie
E30 Zone Newbie
Posts: 181
Joined: Wed Nov 23, 2011 11:00 pm

Post Mon Dec 19, 2011 3:08 pm

well good news i pissed the pulley bolt off using my 1.5meter bar off my 3ton jack.

and he only charged me a tenner for that and the steering rack uj.


but the bush is fcuked on it :( and im guessing by the rivets it cant be changed?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Dec 19, 2011 6:14 pm

gazwhittle wrote:
but the bush is fcuked on it :( and im guessing by the rivets it cant be changed?
No problem changing it. Grind off the rivets, and use the special shouldered bolts that BMW supply, along with nyloc nuts and washers to replace them.
http://bmwfans.info/parts/catalog/E30/2 ... _assembly/
you need a #3 and four of #6.
gazwhittle
E30 Zone Newbie
E30 Zone Newbie
Posts: 181
Joined: Wed Nov 23, 2011 11:00 pm

Post Mon Dec 19, 2011 10:03 pm

Brianmoooore wrote:
gazwhittle wrote:
but the bush is fcuked on it :( and im guessing by the rivets it cant be changed?
No problem changing it. Grind off the rivets, and use the special shouldered bolts that BMW supply, along with nyloc nuts and washers to replace them.
http://bmwfans.info/parts/catalog/E30/2 ... _assembly/
you need a #3 and four of #6.
sweet cheers dude ill ring bmw in the morn!