gearbox chatter?
Moderator: martauto
-
sweep
- Married to the E30 Zone

- Posts: 10110
- Joined: Sat Mar 15, 2008 11:00 pm
- Location: spares & repairs in sheffield
as above is there any fix for this? stripdown?can i get the parts from the dealers??
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
a noisy Layshaft is common Pete, usually due to the tickover being too low ? it will still last forever 
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
Using the correct oil helps. Not ATF!
-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
What is the correct oil? both my cars have ATF.
and the layshaft is a bit rattly on the E30 
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
clipper
- E30 Zone Squatter

- Posts: 1980
- Joined: Mon Aug 22, 2005 11:00 pm
- Location: Madrid
Doesn't help that much !bss325i wrote:Using the correct oil helps. Not ATF!
I speak from recent experience !
These are sensations as hard to forget as they are to ignore.....
-
Mikey_Boy
- E30 Zone Regular

- Posts: 996
- Joined: Sun Mar 16, 2008 11:00 pm
- Location: Cheshire - trying to avoid the bling!
^^^ +1!!
Use of ATF is a daft idea...
Layshaft is definitely the issue here - cured with a rebuild but if you are prepared to put up with it, it will last a looooooong time without going wrong. Putting up the idle speed a touch works wonders!!
Use of ATF is a daft idea...
Layshaft is definitely the issue here - cured with a rebuild but if you are prepared to put up with it, it will last a looooooong time without going wrong. Putting up the idle speed a touch works wonders!!
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
The correct gearbox oil for an E30 is EP80 although you can use a non multigrade SAE30 engine oil.
ATF Dexron makes it rattle, and EP90 can make it hard work to change gear.
ATF Dexron makes it rattle, and EP90 can make it hard work to change gear.
-
sweep
- Married to the E30 Zone

- Posts: 10110
- Joined: Sat Mar 15, 2008 11:00 pm
- Location: spares & repairs in sheffield
i think il take the box out and fit new bearings if they are avalible il look on real oem.
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
I have used EP80W90 or EP80, both are fine.
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
Oh and as for ATF, i tried it years ago upon recommendation by a well known Kent based BMW specialist as a cure for stiff gear changes when cold.
Yes it worked but when hot it was to noisey so i changed back to EP80 and its been fine since.
Yes it worked but when hot it was to noisey so i changed back to EP80 and its been fine since.
-
M42
- E30 Zone Newbie

- Posts: 146
- Joined: Sun Jan 25, 2009 11:00 pm
I had a same the same problem on the M3 and was recomended MTL redline transmision oil, completley stopped the rattle. very good stuff. I think Demon Tweakes sell it.
-
BMWE30325
- E30 Zone Camper

- Posts: 1113
- Joined: Sat Jul 24, 2010 11:00 pm
- Location: South East London
http://www.ebay.co.uk/itm/DX-Three-Hypo ... 2a15d69bb4bss325i wrote:I have used EP80W90 or EP80, both are fine.
one of these?
-
mrb27
- E30 Zone Regular

- Posts: 345
- Joined: Wed Nov 17, 2010 11:00 pm
- Location: Essex
on mine, when at idle i get a rattle from the box, if i put the clutch down it stops, but let it back up and it goes again 
would that be the same thing?
would that be the same thing?
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
yesmrb27 wrote:on mine, when at idle i get a rattle from the box, if i put the clutch down it stops, but let it back up and it goes again
would that be the same thing?
can also be the clutch release bearing
-
mrb27
- E30 Zone Regular

- Posts: 345
- Joined: Wed Nov 17, 2010 11:00 pm
- Location: Essex
bearing and clutch replaced a few weeks back, what can i do to sort the rattle?
new shaft bearings?
new shaft bearings?
-
sam325is
- E30 Zone Addict

- Posts: 2002
- Joined: Thu Jul 06, 2006 11:00 pm
- Location: Cheltenham
http://www.amsoil.com/storefront/atd.aspxbss325i wrote:Oh and as for ATF, i tried it years ago upon recommendation by a well known Kent based BMW specialist as a cure for stiff gear changes when cold.
Yes it worked but when hot it was to noisey so i changed back to EP80 and its been fine since.
Use this. it hardly thins with temperature. No rattle on start up and smooth gear changes. Once fully warmend up the rattle is still there a tiny bit but overall it makes a massive improvement.
I bought it from oilman.
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
Thanks for the recommendation but i'll stick with the correct EP80 as i dont get any chatter now on idle at any temp.sam325is wrote:http://www.amsoil.com/storefront/atd.aspxbss325i wrote:Oh and as for ATF, i tried it years ago upon recommendation by a well known Kent based BMW specialist as a cure for stiff gear changes when cold.
Yes it worked but when hot it was to noisey so i changed back to EP80 and its been fine since.
Use this. it hardly thins with temperature. No rattle on start up and smooth gear changes. Once fully warmend up the rattle is still there a tiny bit but overall it makes a massive improvement.
I bought it from oilman.
-
sam325is
- E30 Zone Addict

- Posts: 2002
- Joined: Thu Jul 06, 2006 11:00 pm
- Location: Cheltenham
Thats good
a happy gear box. But i meant for sweep. Also its worth taking not of the colour of the sticker on the housing of your bear box. Some of the manual gear boxes are supposed to have ATF in them.
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
That's correct, some manual trans are meant to use ATF but the getrag 260 used in the 325i is meant to use convertional EP80.
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Years ago, I had a Cortina with a layshaft rattle that would wake the dead. Draining and refilling it with EP140 made it quieter...........
