Valve clearances (again)
Moderator: martauto
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
Sorry for starting another thread on valve clearances - I have done a search which as taught me all I know so far but have a few questions I couldn't definitively find the answer to.
Engine is an M20B25
I assume what you do 1 cylinder at a time - both valves?
What I understand:
clearance on stone cold engine is 0.25mm and should have some drag when sliding feeler in and out.
When the cam lobe is pointing all the way down this means the valves are closed (TDC?)
So if I have cylinder 1 cam lobe pointing down I have to use the rule of 7 which means that I now adjust the clearance on cyl 6?
cheers
Engine is an M20B25
I assume what you do 1 cylinder at a time - both valves?
What I understand:
clearance on stone cold engine is 0.25mm and should have some drag when sliding feeler in and out.
When the cam lobe is pointing all the way down this means the valves are closed (TDC?)
So if I have cylinder 1 cam lobe pointing down I have to use the rule of 7 which means that I now adjust the clearance on cyl 6?
cheers
'88 325i Auto Chromie Cabriolet in Alpine White
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
I have looked at that, but that suggests that you adjust the each valve when it's lobe is pointing directly down - When doing a search on here I read conflicting views?
'88 325i Auto Chromie Cabriolet in Alpine White
-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
I do each valve individually starting at cyl 1, maybe cyl 5 exhaust will be shut but work on one cyl at a time and you wont go wrong.
Yes, the rocker is adjusted with the cam lob down, ie valve shut.
Yes, the rocker is adjusted with the cam lob down, ie valve shut.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
Right so cyl 1 inlet valve lobe down. adjust. Rotate crank. cyl 1 exhaust lobe down. adjust. Rotate crank. Cyl 2... etc etc.
Sorry I'm being thick but this is the first motor I've played with that doesn't have hydraulic ones!
Cheers
Sorry I'm being thick but this is the first motor I've played with that doesn't have hydraulic ones!
Cheers
'88 325i Auto Chromie Cabriolet in Alpine White
-
215m3
- E30 Zone Regular

- Posts: 328
- Joined: Sun Oct 23, 2005 11:00 pm
Hi James
Create a spreadsheet with the cylinders 1 to 6 and exhaust and inlet. When the pointed end of the lobe is pointing towards the sky, the valve will be shut. Start at the front of the engine, measure the gap with a feeler and record on the spreadsheet.
Look down the cam to find the next lobe pointing towards the sky, then rotate and repeat until they are all done. On the spreadsheet add the gap allowance and then see which are to wide, too narrow or in allowance. Swap or replace those out with the allowed tollerance.
HTH's
Create a spreadsheet with the cylinders 1 to 6 and exhaust and inlet. When the pointed end of the lobe is pointing towards the sky, the valve will be shut. Start at the front of the engine, measure the gap with a feeler and record on the spreadsheet.
Look down the cam to find the next lobe pointing towards the sky, then rotate and repeat until they are all done. On the spreadsheet add the gap allowance and then see which are to wide, too narrow or in allowance. Swap or replace those out with the allowed tollerance.
HTH's
Toby
1987 E30 M3 S14 Turbo
1971 V12 E type Roadster
1987 E30 M3 S14 Turbo
1971 V12 E type Roadster
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
sorry toby but thats not right the lobe has to be facing down for the valve to be shut if the lobe is pointing up that means its on cam and the valve will be fully open
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
umm, no:
the lobe (centre line) facing up as identified in the pic below in comparison to the mid point of the base circle - should be pointing upwards, inline with the valve stem

the lobe (centre line) facing up as identified in the pic below in comparison to the mid point of the base circle - should be pointing upwards, inline with the valve stem

-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
yes which means the valve is then open the valve needs to be shut to do valve clearances which needs to be pointing down
-
chh137
- E30 Zone Squatter

- Posts: 1502
- Joined: Mon Apr 18, 2011 11:00 pm
- Location: deepest darkest derbyshire
desmodronic (spelling) valve gear on a M20B25 ?
-
Jim320i
- E30 Zone News / COTM Team

- Posts: 10627
- Joined: Sun Oct 25, 2009 11:00 pm
- Location: Leicestershire
You sure Barx? If so, my Engine is foook
http://www.e30zone.net/e30zonewiki/inde ... M20_engine
Step 6 says different...
Thats how I have set mine up, same as a few other zoners cars which I have done...
http://www.e30zone.net/e30zonewiki/inde ... M20_engine
Step 6 says different...
Thats how I have set mine up, same as a few other zoners cars which I have done...
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
if i adjusted mine like that they would be clattering like a bitch if not brake some thing
-
leeparkes
- Married to the E30 Zone

- Posts: 9535
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
Rocker needs to be touching the middle of the base circle.



Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
+ 1 on thatleeparkes wrote:Rocker needs to be touching the middle of the base circle.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
M20 engine has rockers, so the cam opens the valve when the lobes are pointing up! As a consequence of this you adjust the clearance on a particular lobe when it's pointing down.
When 6 is pointing up; i.e the valves on 6 are open, adjust 1.
Turn the crankshaft forwards 60 degrees, with a 22mm spanner on the crank bolt, and the valves on 2 will be open, so adjust 5. Keep going, 60 degrees at a time, until you have turned the crank two full turns and the job will be done.
If you're not confident of knowing what a "sliding fit" is for the feeler gauge, check with another one 1 thou' thinner, which should go in easily, and another one 1 thou' thicker, which should need forcing in.
When 6 is pointing up; i.e the valves on 6 are open, adjust 1.
Turn the crankshaft forwards 60 degrees, with a 22mm spanner on the crank bolt, and the valves on 2 will be open, so adjust 5. Keep going, 60 degrees at a time, until you have turned the crank two full turns and the job will be done.
If you're not confident of knowing what a "sliding fit" is for the feeler gauge, check with another one 1 thou' thinner, which should go in easily, and another one 1 thou' thicker, which should need forcing in.
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
Right, I think I know what I'm doing now chaps thanks for the input!
Will have a go tomorrow.
Will have a go tomorrow.
'88 325i Auto Chromie Cabriolet in Alpine White

