centre prop bearing change

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
randomspeedfreak
E30 Zone Regular
E30 Zone Regular
Posts: 992
Joined: Mon Mar 15, 2010 11:00 pm
Location: Bristol

Post Fri Nov 04, 2011 6:04 pm

The rubber on the propshaft I'm putting inis shot, any advice on changing this? I'm in the garage at the moment and its a nightmare!
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Fri Nov 04, 2011 6:08 pm

not a hard job really
User avatar
randomspeedfreak
E30 Zone Regular
E30 Zone Regular
Posts: 992
Joined: Mon Mar 15, 2010 11:00 pm
Location: Bristol

Post Fri Nov 04, 2011 6:29 pm

threelander wrote:not a hard job really
Cheers very informative
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Fri Nov 04, 2011 7:11 pm

Separate the propshaft by undoing the big sleeve nut in the centre. The holder for the centre bearing is just bolted to the floor with the 2 13mm bolts.

You will need some circlip pliers to get the circlip off. The centre bearing should then slide off the prop



Check what condition the bearing is in as it may be worth changing that as well as the carrier
Rav335uk
E30 Zone Meets/Events Team
E30 Zone Meets/Events Team
Posts: 27978
Joined: Wed Jan 19, 2005 11:00 pm
Location: Mad mad mad

Post Fri Nov 04, 2011 7:17 pm

Make sure you mark the prop so it goes back balanced.
Image
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
User avatar
randomspeedfreak
E30 Zone Regular
E30 Zone Regular
Posts: 992
Joined: Mon Mar 15, 2010 11:00 pm
Location: Bristol

Post Fri Nov 04, 2011 8:21 pm

cheers boys,
Ive marked the prop, but im planning on using the back section of another, as it is in better nic. is this a recipe for disaster?

i have 1 good bearing out of the two, i killed the other bearing trying to get it off, its not sliding off that simply. any advice aside from just cleaning it up as much as possible? dont want to murder 2 of them.
also the rubber is looking a bit tired, isit a big deal? should i renew this or is it not a problem?
cheers,
Matt
Rav335uk
E30 Zone Meets/Events Team
E30 Zone Meets/Events Team
Posts: 27978
Joined: Wed Jan 19, 2005 11:00 pm
Location: Mad mad mad

Post Fri Nov 04, 2011 8:28 pm

randomspeedfreak wrote:cheers boys,
Ive marked the prop, but im planning on using the back section of another, as it is in better nic. is this a recipe for disaster?

cheers,
Matt
Yes, but easily fixed, you'll need to have it rebalanced before you fit it to the car though.
Image
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Fri Nov 04, 2011 8:28 pm

most props i have come across have a white dot, so they are easy to line up. But you may not get a perfect balance combining 2 different one.

For the sake of £30 or so, I'd just stick a new bearing & carrier in there.