centre prop bearing change
Moderator: martauto
-
randomspeedfreak
- E30 Zone Regular

- Posts: 992
- Joined: Mon Mar 15, 2010 11:00 pm
- Location: Bristol
The rubber on the propshaft I'm putting inis shot, any advice on changing this? I'm in the garage at the moment and its a nightmare!
-
randomspeedfreak
- E30 Zone Regular

- Posts: 992
- Joined: Mon Mar 15, 2010 11:00 pm
- Location: Bristol
Cheers very informativethreelander wrote:not a hard job really
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
Separate the propshaft by undoing the big sleeve nut in the centre. The holder for the centre bearing is just bolted to the floor with the 2 13mm bolts.
You will need some circlip pliers to get the circlip off. The centre bearing should then slide off the prop
Check what condition the bearing is in as it may be worth changing that as well as the carrier
You will need some circlip pliers to get the circlip off. The centre bearing should then slide off the prop
Check what condition the bearing is in as it may be worth changing that as well as the carrier
-
Rav335uk
- E30 Zone Meets/Events Team

- Posts: 27978
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
Make sure you mark the prop so it goes back balanced.

If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
randomspeedfreak
- E30 Zone Regular

- Posts: 992
- Joined: Mon Mar 15, 2010 11:00 pm
- Location: Bristol
cheers boys,
Ive marked the prop, but im planning on using the back section of another, as it is in better nic. is this a recipe for disaster?
i have 1 good bearing out of the two, i killed the other bearing trying to get it off, its not sliding off that simply. any advice aside from just cleaning it up as much as possible? dont want to murder 2 of them.
also the rubber is looking a bit tired, isit a big deal? should i renew this or is it not a problem?
cheers,
Matt
Ive marked the prop, but im planning on using the back section of another, as it is in better nic. is this a recipe for disaster?
i have 1 good bearing out of the two, i killed the other bearing trying to get it off, its not sliding off that simply. any advice aside from just cleaning it up as much as possible? dont want to murder 2 of them.
also the rubber is looking a bit tired, isit a big deal? should i renew this or is it not a problem?
cheers,
Matt
-
Rav335uk
- E30 Zone Meets/Events Team

- Posts: 27978
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
Yes, but easily fixed, you'll need to have it rebalanced before you fit it to the car though.randomspeedfreak wrote:cheers boys,
Ive marked the prop, but im planning on using the back section of another, as it is in better nic. is this a recipe for disaster?
cheers,
Matt

If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
most props i have come across have a white dot, so they are easy to line up. But you may not get a perfect balance combining 2 different one.
For the sake of £30 or so, I'd just stick a new bearing & carrier in there.
For the sake of £30 or so, I'd just stick a new bearing & carrier in there.

