320i waterpump
Moderator: martauto
-
jimbob29
- E30 Zone Regular

- Posts: 266
- Joined: Tue Apr 26, 2011 11:00 pm
- Location: isle of wight
after a rumbling sound from the front of the 320i engine when up to temp turns out that the water pump bearing has failed but no leaks no overheating ect i found out that these are bugger to change.how long will the pump last with a worn bearing and how much would a garage charge to replace?
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
changing the pump means the timing belt comes off. Considering you can't re-use a timing belt, that's the job you have to price up. Garages will milk that, because although it's only a two hour job for someone with experience, most people are too scared to tackle it myself. Quote is normally a couple of hundred, plus parts.
There's plenty of guides online to doing it yourself.
There's plenty of guides online to doing it yourself.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Sanchez
- Married to the E30 Zone

- Posts: 7578
- Joined: Sun Apr 17, 2005 11:00 pm
- Location: Sunny Scotland
Get a metal impellor water pump as well, last longer.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Timing belt doesn't have to come off, and the pump on a 320 isn't at all difficult to change!
Get stuck in!
Leave the timing belt tensioner spring and guide pin off when you fit the pump, and keep them in a safe place until the next belt change (or just buy new ones when needed).
Get stuck in!
Leave the timing belt tensioner spring and guide pin off when you fit the pump, and keep them in a safe place until the next belt change (or just buy new ones when needed).
-
mrb27
- E30 Zone Regular

- Posts: 345
- Joined: Wed Nov 17, 2010 11:00 pm
- Location: Essex
i did mine a few weeks back, didnt remove the timing belt, easy job imo
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Don't think I'd be leaving the spring and pin out - although it won't really make much odds. They can be an absolute bastard to refit. The problem is that the other end of the pin sits against the water pump. The way I do it is this:
With the belt covers off, slacken the long tensioner pillar bolt, and the 13mm lock bolt. Push the tensioner back against the spring about 3mm, tighten the lock bolt. Use a pair of very small locking grips on the end of the pin so that the spring and pin are under compression. Slacken the 13mm lock bolt, push the tensioner wheel back to where it was and retighten. The water pump end of the tensioner pin is now clear of the pump. Replace the water pump, slacken the 13mm lock bolt and release the small grips on the pin - the tensioner will then release, tensioning the belt. Tighten then lock bolt and pillar bolt, job done.
However, if the belt has done upwards of 20'000 miles, it's a good idea to change both the belt and the tensioner early - you're already halfway there.
With the belt covers off, slacken the long tensioner pillar bolt, and the 13mm lock bolt. Push the tensioner back against the spring about 3mm, tighten the lock bolt. Use a pair of very small locking grips on the end of the pin so that the spring and pin are under compression. Slacken the 13mm lock bolt, push the tensioner wheel back to where it was and retighten. The water pump end of the tensioner pin is now clear of the pump. Replace the water pump, slacken the 13mm lock bolt and release the small grips on the pin - the tensioner will then release, tensioning the belt. Tighten then lock bolt and pillar bolt, job done.
However, if the belt has done upwards of 20'000 miles, it's a good idea to change both the belt and the tensioner early - you're already halfway there.
-
groovylee
- E30 Zone Regular

- Posts: 356
- Joined: Sat Aug 13, 2011 11:00 pm
- Location: Shefford, Beds
as andy says above really. i did my first e30 cambelt change on my 1990 cabrio, and the hardest thing was removing the bonnet to make access easier. all in it took me 3 hours for cambelt, waterpump, and tensioner. just follow the guides and you can't go wrong, especially if the belt is staying on, but as said above, if it has already got quite a few miles on it, it would be worth changing it for the sake of a few quid for a belt.
good luck dude
good luck dude
-
mrb27
- E30 Zone Regular

- Posts: 345
- Joined: Wed Nov 17, 2010 11:00 pm
- Location: Essex
when i refitted mine i tilted the pump into place with the pin/spring in place and wiggled it into place, was a bit of a pain but i got there 
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
A very good way of tearing the gasket!mrb27 wrote:when i refitted mine i tilted the pump into place with the pin/spring in place and wiggled it into place, was a bit of a pain but i got there
Spring and pin have absolutely no purpose, other than when actually fitting a cambelt.
-
mrb27
- E30 Zone Regular

- Posts: 345
- Joined: Wed Nov 17, 2010 11:00 pm
- Location: Essex
well i didnt tear mine
skills my friend 
-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
Really?!Brianmoooore wrote:A very good way of tearing the gasket!mrb27 wrote:when i refitted mine i tilted the pump into place with the pin/spring in place and wiggled it into place, was a bit of a pain but i got there
Spring and pin have absolutely no purpose, other than when actually fitting a cambelt.
I will keep that in mind as there a bastard to get back
By the way, why dont u give this job a shot? Or are u no good with tools?
E30 Crazy!
