320i engine noise
Moderator: martauto
-
jimbob29
- E30 Zone Regular

- Posts: 266
- Joined: Tue Apr 26, 2011 11:00 pm
- Location: isle of wight
i have this rumbling metallic sound from the front of the engine around the distributor cap area when warmed up and cant figure out if its a cam problem its not that loud and doesnt get louder when revs increase?car still runs perfectly.how can tell if its the cam?
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
When did you last change the oil?
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
jimbob29
- E30 Zone Regular

- Posts: 266
- Joined: Tue Apr 26, 2011 11:00 pm
- Location: isle of wight
3 months ago 10w 40 allways checked weekly it might be one of pulleys but can be sure?
-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
Water pump bearing failure?
E30 Crazy!
-
jimbob29
- E30 Zone Regular

- Posts: 266
- Joined: Tue Apr 26, 2011 11:00 pm
- Location: isle of wight
it does sound louder on that side but bloody cant pin point the sound
if it was the cam would you hear it all along the rocker cover?its only when engine is up to temp so heat must be playing a part in it?its either water pump bearing or one of the pulleys and its around distributor area
-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
Remove the rocker cover and check the camshaft lobes for wear and pitting. If all is well, then strip the aux belts and feel all the pulleys for play and wear. If all is well there, then id go checking the water pump
My 320i used to make a slight rumbling noise when at running temp and it turned out to be a worn out water pump. New pump and belt fitted. Rumbling gone... But check all the pulleys first
My 320i used to make a slight rumbling noise when at running temp and it turned out to be a worn out water pump. New pump and belt fitted. Rumbling gone... But check all the pulleys first
E30 Crazy!
-
mrb27
- E30 Zone Regular

- Posts: 345
- Joined: Wed Nov 17, 2010 11:00 pm
- Location: Essex
had the same a few weeks back but mine was constant noise, with yours i would run it up to temperature, switch off, slack off the belts, pull em off the pullys and fire it up again briefly, if the noise is still there that will eliminate w.pump, viscous, p.a.s pump, alt,
if it stops you know its one of the above. dont let it run for more than a min though as you dont want it to heat up too much and make sure the belts are well out of the way when you fire it up.
if it stops you know its one of the above. dont let it run for more than a min though as you dont want it to heat up too much and make sure the belts are well out of the way when you fire it up.
-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
Don't turn the engine over with the timing belt slack. I know its plain common knowlegde but hey.
E30 Crazy!
-
mrb27
- E30 Zone Regular

- Posts: 345
- Joined: Wed Nov 17, 2010 11:00 pm
- Location: Essex
lol that would be funny as fook!! clang bang oh shit......Ajsingh wrote:Don't turn the engine over with the timing belt slack. I know its plain common knowlegde but hey.
