i'm losing a little fluid from my clutch hydraulics, the actual servo unit is only 2yrs old (covered 6000K miles) it was a brand new unit fitted by last owner.
ive been under the car and can see that the fluid is leaking from behind the unit, the bolt's are tight.. is there a simple O-ring seal needing replaced or am i better replacing the unit itself?
thank's
clutch servo/fluid...
Moderator: martauto
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Only servo on your car is part of the braking system. Are you referring to the clutch slave cylinder?
If it is, you don't normally see a leak directly from it. The fluid drips from a small slot between the gearbox and engine, right at the bottom.
If it is, you don't normally see a leak directly from it. The fluid drips from a small slot between the gearbox and engine, right at the bottom.
-
Billwill
- E30 Zone Regular

- Posts: 363
- Joined: Sun Jun 26, 2011 11:00 pm
- Location: South Africa
Servo unit? You mean the master cylinder?
There is a kit to replace the rubber bits in the clutch slave cylinder which actuates the clutch as well as a kit for the clutch master cylinder which is what the clutch pedal operates.
It is advisable to do both kits at once and off course bleed the system out.
The brakes are what have a servo...LHD drive E30s share the same fluid resevouir for the brakes and the clutch; RHD E30s have seperate resevouirs for brakes and clutch.
Is it your "brake" Servo and resevour that is leaking?
There is a kit to replace the rubber bits in the clutch slave cylinder which actuates the clutch as well as a kit for the clutch master cylinder which is what the clutch pedal operates.
It is advisable to do both kits at once and off course bleed the system out.
The brakes are what have a servo...LHD drive E30s share the same fluid resevouir for the brakes and the clutch; RHD E30s have seperate resevouirs for brakes and clutch.
Is it your "brake" Servo and resevour that is leaking?
-
blue30
- E30 Zone Regular

- Posts: 354
- Joined: Wed Jan 09, 2008 11:00 pm
- Location: Stoke on Trent
If you're talking the back of the clutch slave cylinder, it's got to be the connection or the bleed nipple not sealing.
-
320iAN
- E30 Zone Camper

- Posts: 1395
- Joined: Sat Sep 16, 2006 11:00 pm
- Location: West Scotland
oops yeah i meant the clutch master cylinder
there is a small "snail trail" of fluid running between the actual unit & the gearbox (the face it sit's against)
there is a small "snail trail" of fluid running between the actual unit & the gearbox (the face it sit's against)

-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
The master cylinder is the one inside the car connected to the pedal, the slave cylinder is the one that is bolted to the gearbox.
Could be just the bleed nipple thats loose ( although unlikely if its been OK for 2 Years and untouched )
The slave is a fiddly bitch to change - difficult to get a socket on the top nut as access is very tight. Change the flexi hose while you're at it. You can get braided ones off ebay.
Good luck
Could be just the bleed nipple thats loose ( although unlikely if its been OK for 2 Years and untouched )
The slave is a fiddly bitch to change - difficult to get a socket on the top nut as access is very tight. Change the flexi hose while you're at it. You can get braided ones off ebay.
Good luck

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
320iAN
- E30 Zone Camper

- Posts: 1395
- Joined: Sat Sep 16, 2006 11:00 pm
- Location: West Scotland
thank's.. the flexi was also replaced with the slave cylinder, am i better to change the whole unit or do folk think i just need to renew a seal/O-ring?
thanks again for all & any help
thanks again for all & any help

