clutch servo/fluid...

Need technical Q/A then you're in the right place

Moderator: martauto

320iAN
E30 Zone Camper
E30 Zone Camper
Posts: 1395
Joined: Sat Sep 16, 2006 11:00 pm
Location: West Scotland

Post Fri Oct 07, 2011 10:32 am

i'm losing a little fluid from my clutch hydraulics, the actual servo unit is only 2yrs old (covered 6000K miles) it was a brand new unit fitted by last owner.
ive been under the car and can see that the fluid is leaking from behind the unit, the bolt's are tight.. is there a simple O-ring seal needing replaced or am i better replacing the unit itself?

thank's
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Oct 07, 2011 1:17 pm

Only servo on your car is part of the braking system. Are you referring to the clutch slave cylinder?
If it is, you don't normally see a leak directly from it. The fluid drips from a small slot between the gearbox and engine, right at the bottom.
User avatar
Billwill
E30 Zone Regular
E30 Zone Regular
Posts: 363
Joined: Sun Jun 26, 2011 11:00 pm
Location: South Africa

Post Fri Oct 07, 2011 1:21 pm

Servo unit? You mean the master cylinder?

There is a kit to replace the rubber bits in the clutch slave cylinder which actuates the clutch as well as a kit for the clutch master cylinder which is what the clutch pedal operates.
It is advisable to do both kits at once and off course bleed the system out.
The brakes are what have a servo...LHD drive E30s share the same fluid resevouir for the brakes and the clutch; RHD E30s have seperate resevouirs for brakes and clutch.
Is it your "brake" Servo and resevour that is leaking?
User avatar
blue30
E30 Zone Regular
E30 Zone Regular
Posts: 354
Joined: Wed Jan 09, 2008 11:00 pm
Location: Stoke on Trent

Post Fri Oct 07, 2011 2:10 pm

If you're talking the back of the clutch slave cylinder, it's got to be the connection or the bleed nipple not sealing.
320iAN
E30 Zone Camper
E30 Zone Camper
Posts: 1395
Joined: Sat Sep 16, 2006 11:00 pm
Location: West Scotland

Post Fri Oct 07, 2011 2:28 pm

oops yeah i meant the clutch master cylinder :o:
there is a small "snail trail" of fluid running between the actual unit & the gearbox (the face it sit's against)
Image
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Fri Oct 07, 2011 3:07 pm

The master cylinder is the one inside the car connected to the pedal, the slave cylinder is the one that is bolted to the gearbox.

Could be just the bleed nipple thats loose ( although unlikely if its been OK for 2 Years and untouched )

The slave is a fiddly bitch to change - difficult to get a socket on the top nut as access is very tight. Change the flexi hose while you're at it. You can get braided ones off ebay.

Good luck
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
320iAN
E30 Zone Camper
E30 Zone Camper
Posts: 1395
Joined: Sat Sep 16, 2006 11:00 pm
Location: West Scotland

Post Fri Oct 07, 2011 4:09 pm

thank's.. the flexi was also replaced with the slave cylinder, am i better to change the whole unit or do folk think i just need to renew a seal/O-ring?

thanks again for all & any help :)
Image