Cylinder Head Bolts
Moderator: martauto
-
TPS
- E30 Zone Team Member

- Posts: 13119
- Joined: Fri Mar 06, 2009 11:00 pm
- Location: Hampshire
I've got to take off an head off a facelift 320 engine, does anyone know if the bolts are the torx or hex type?

1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
If they are hex bolts,do not put them back!
It's the hex-headed bolt heads that snap off,get under a rocker and cause mayhem.
Buy a set of torx streech bolt to re-build with.
It's the hex-headed bolt heads that snap off,get under a rocker and cause mayhem.
Buy a set of torx streech bolt to re-build with.
Youth is wasted on the young.
-
TPS
- E30 Zone Team Member

- Posts: 13119
- Joined: Fri Mar 06, 2009 11:00 pm
- Location: Hampshire
If they're torx, what size socket do I need?

1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
E14!
No idea about the hex-headed one's,but an educated guess would be 13mm.
No idea about the hex-headed one's,but an educated guess would be 13mm.
Youth is wasted on the young.
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
Hex heads are 17mm, the torx size is 14, it's facelift so it will be torx 
-
TPS
- E30 Zone Team Member

- Posts: 13119
- Joined: Fri Mar 06, 2009 11:00 pm
- Location: Hampshire
Thanks Malcolm/Steve, luckily the Engine is on the garage floor, so should be alot easier to work on!

1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Not always. Torx head bolts were introduded early 1989.e30topless wrote:Hex heads are 17mm, the torx size is 14, it's facelift so it will be torx
-
TPS
- E30 Zone Team Member

- Posts: 13119
- Joined: Fri Mar 06, 2009 11:00 pm
- Location: Hampshire
The engine is from 1988

1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
It will have left the factory with 17mm hex, unless they've already been changed. Keep the fat washers and use them on the new torx bolts.
-
TPS
- E30 Zone Team Member

- Posts: 13119
- Joined: Fri Mar 06, 2009 11:00 pm
- Location: Hampshire
Thanks Andy, I'll let you know how it goes.

1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
-
TPS
- E30 Zone Team Member

- Posts: 13119
- Joined: Fri Mar 06, 2009 11:00 pm
- Location: Hampshire
They were 17mm Hex, undid them a quarter of a turn at a time, in sequence, according to the Bentley book. Got splattered with petrol, where the FPR was still attached, apart from that, Surprisingly easy in the end, thanks for everyones help.

1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
-
retroboyo
- E30 Zone Regular

- Posts: 459
- Joined: Mon Oct 30, 2006 11:00 pm
Do you have to use new head bolts if you take the head off, I'm about to do mine
-
TPS
- E30 Zone Team Member

- Posts: 13119
- Joined: Fri Mar 06, 2009 11:00 pm
- Location: Hampshire
Yes, don't re-use the old ones, also make sure when your tightening/loosening the bolts, they're done in the right order.

1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
