Cylinder Head Bolts

Need technical Q/A then you're in the right place

Moderator: martauto

TPS
E30 Zone Team Member
E30 Zone Team Member
Posts: 13119
Joined: Fri Mar 06, 2009 11:00 pm
Location: Hampshire

Post Sat Sep 17, 2011 6:36 pm

I've got to take off an head off a facelift 320 engine, does anyone know if the bolts are the torx or hex type?
Image
1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Sep 17, 2011 6:49 pm

If they are hex bolts,do not put them back!

It's the hex-headed bolt heads that snap off,get under a rocker and cause mayhem.

Buy a set of torx streech bolt to re-build with.
Youth is wasted on the young.
TPS
E30 Zone Team Member
E30 Zone Team Member
Posts: 13119
Joined: Fri Mar 06, 2009 11:00 pm
Location: Hampshire

Post Sat Sep 17, 2011 6:55 pm

If they're torx, what size socket do I need?
Image
1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Sep 17, 2011 7:04 pm

E14! :D

No idea about the hex-headed one's,but an educated guess would be 13mm.
Youth is wasted on the young.
e30topless
E30 Zone Team Member
E30 Zone Team Member
Posts: 13595
Joined: Wed Aug 23, 2006 11:00 pm
Location: surrounded by scrap

Post Sat Sep 17, 2011 7:09 pm

Hex heads are 17mm, the torx size is 14, it's facelift so it will be torx :)
TPS
E30 Zone Team Member
E30 Zone Team Member
Posts: 13119
Joined: Fri Mar 06, 2009 11:00 pm
Location: Hampshire

Post Sat Sep 17, 2011 7:52 pm

Thanks Malcolm/Steve, luckily the Engine is on the garage floor, so should be alot easier to work on!
Image
1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Sat Sep 17, 2011 8:30 pm

e30topless wrote:Hex heads are 17mm, the torx size is 14, it's facelift so it will be torx :)
Not always. Torx head bolts were introduded early 1989.
TPS
E30 Zone Team Member
E30 Zone Team Member
Posts: 13119
Joined: Fri Mar 06, 2009 11:00 pm
Location: Hampshire

Post Sat Sep 17, 2011 8:32 pm

The engine is from 1988
Image
1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Sat Sep 17, 2011 10:29 pm

It will have left the factory with 17mm hex, unless they've already been changed. Keep the fat washers and use them on the new torx bolts.
TPS
E30 Zone Team Member
E30 Zone Team Member
Posts: 13119
Joined: Fri Mar 06, 2009 11:00 pm
Location: Hampshire

Post Sun Sep 18, 2011 7:57 am

Thanks Andy, I'll let you know how it goes.
Image
1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
TPS
E30 Zone Team Member
E30 Zone Team Member
Posts: 13119
Joined: Fri Mar 06, 2009 11:00 pm
Location: Hampshire

Post Sun Sep 18, 2011 11:32 am

They were 17mm Hex, undid them a quarter of a turn at a time, in sequence, according to the Bentley book. Got splattered with petrol, where the FPR was still attached, apart from that, Surprisingly easy in the end, thanks for everyones help.
Image
1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
retroboyo
E30 Zone Regular
E30 Zone Regular
Posts: 459
Joined: Mon Oct 30, 2006 11:00 pm

Post Mon Sep 19, 2011 10:47 am

Do you have to use new head bolts if you take the head off, I'm about to do mine
TPS
E30 Zone Team Member
E30 Zone Team Member
Posts: 13119
Joined: Fri Mar 06, 2009 11:00 pm
Location: Hampshire

Post Mon Sep 19, 2011 10:51 am

Yes, don't re-use the old ones, also make sure when your tightening/loosening the bolts, they're done in the right order.
Image
1991 325i Touring Alpine White II
1994 318i Touring Sterling Silver
retroboyo
E30 Zone Regular
E30 Zone Regular
Posts: 459
Joined: Mon Oct 30, 2006 11:00 pm

Post Mon Sep 19, 2011 11:13 am

Thank you