replacing front wing n doors

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
jimbob29
E30 Zone Regular
E30 Zone Regular
Posts: 266
Joined: Tue Apr 26, 2011 11:00 pm
Location: isle of wight

Post Wed Aug 24, 2011 11:42 am

is the front wing welded on?or just bolts?and how easy is it to removal drivers door n rear passenger door?is it a job i can do or best left for the garage?thought it might work out cheaper to replace rather than respray..
Ranchero
E30 Zone Addict
E30 Zone Addict
Posts: 2563
Joined: Thu Sep 17, 2009 11:00 pm

Post Wed Aug 24, 2011 12:09 pm

The wing is bolted on. About seven 8mm bolts along the top, another at the bottom. Two 10mm on the inside wing by the door and another one ( I think) by the headlight. You'll need to remove the plastic arch liner also.

The doors are fairly simple aswell. Remove electronics plug, push off clips holding door pins in place, knock 3 pins out and lift door off.
Image
Sanchez
Married to the E30 Zone
Married to the E30 Zone
Posts: 7578
Joined: Sun Apr 17, 2005 11:00 pm
Location: Sunny Scotland

Post Wed Aug 24, 2011 12:24 pm

Easy work if you no how to use a ratch and some spanners.
Image
User avatar
m8782538
E30 Zone Squatter
E30 Zone Squatter
Posts: 1550
Joined: Mon Feb 07, 2011 11:00 pm
Location: Swindon

Post Wed Aug 24, 2011 1:09 pm

I have a to replace a wing too, not looking forward to it, especially since i found out i may need to take off the front bumper and headlamps etc to get to the bolt.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Wed Aug 24, 2011 1:13 pm

Front wings are held by a variety of fasteners,you will need to remove the bumper first.

Do not un-bolt the doors at the hinge mounts,seperate the door stop at it's clevis pin,un-plug the electrics,then remove the two 8mm bolts that act hinge pins and it will just lift off.

The gain in doing it this way is that the replacement door fitted in the same way,will line up perfectly.
Youth is wasted on the young.
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Wed Aug 24, 2011 1:44 pm

Also make sure you pick up a tube of seam sealer (NOT bathroom silicone sealant). Before the new wing is offered up and bolted, run a thick line of sealant along the top of the inner wing, all the way to the bulkhead. Then put the new wing on, and wipe up the excess sealant that gloops out.

To remove the bumper, you'll need a Torx T55 socket to undo the two big bolts underneath. That can be the hardest part. Then undo the screws inside the wheel arches holding on the sides of the bumper. Then, as you slide the bumper of its mounts, get ready to unclip the wiring plugs to the indicators; pull too hard on the bumper and you'll rip them out, and after 20 years you'll break the actual wires and have to fabricate your own solution.

Apart from that, it's a piece of cake.
User avatar
m8782538
E30 Zone Squatter
E30 Zone Squatter
Posts: 1550
Joined: Mon Feb 07, 2011 11:00 pm
Location: Swindon

Post Wed Aug 24, 2011 1:50 pm

oh joy, torx T55 socket, stupid question, what does one of those look like?????

Bumper - pain

Then the arch liner and then the actual wing which is easy enough.

Glad this is one of the last jobs i have to do, followed by the welding and trying to get the wheels off (for a refurb) and replace the brakes.

Also now HAVE to have this project finished by Christmas or its going to take at least another 12-18months ontop of the original 12mths for completion :eek: . total nightmare.
Rav335uk
E30 Zone Meets/Events Team
E30 Zone Meets/Events Team
Posts: 27978
Joined: Wed Jan 19, 2005 11:00 pm
Location: Mad mad mad

Post Wed Aug 24, 2011 2:21 pm

Torx socket

Image
Image
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
User avatar
m8782538
E30 Zone Squatter
E30 Zone Squatter
Posts: 1550
Joined: Mon Feb 07, 2011 11:00 pm
Location: Swindon

Post Wed Aug 24, 2011 4:31 pm

Thanks, have to go an invest in one of those then otherwise i'm not going to get very far.
Ranchero
E30 Zone Addict
E30 Zone Addict
Posts: 2563
Joined: Thu Sep 17, 2009 11:00 pm

Post Wed Aug 24, 2011 4:45 pm

You wont need the torx socket if you've got chrome bumpers. winkeye
Image
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Wed Aug 24, 2011 6:48 pm

Grrrmachine wrote:Also make sure you pick up a tube of seam sealer (NOT bathroom silicone sealant). Before the new wing is offered up and bolted, run a thick line of sealant along the top of the inner wing, all the way to the bulkhead. Then put the new wing on, and wipe up the excess sealant that gloops out.
Same stuff as used on the seams only in a tube or differnt stuff? I was going to run a bead of tiger seal on the underside when re-fitting the wings :o:
Ranchero
E30 Zone Addict
E30 Zone Addict
Posts: 2563
Joined: Thu Sep 17, 2009 11:00 pm

Post Wed Aug 24, 2011 7:04 pm

Am I right in thinking the sealant only goes on a very small section of the wing? The top edge nearest the scuttle?
Image
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Wed Aug 24, 2011 8:29 pm

You run a bead of sealant along the edge where the bolts go in, so it runs all the way from the headlamp to the scuttle.

Not an E30, but it'll look like this, then you drop the wing on top of it:

Image
Ranchero
E30 Zone Addict
E30 Zone Addict
Posts: 2563
Joined: Thu Sep 17, 2009 11:00 pm

Post Wed Aug 24, 2011 8:34 pm

They wouldn't have come out of the factory like that though, would they?
Image
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Wed Aug 24, 2011 8:48 pm

Ranchero wrote:They wouldn't have come out of the factory like that though, would they?
maybe not all the way down but certainly at the top.
Image

'88 e30 328i M52 track bint.
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Wed Aug 24, 2011 8:49 pm

Ranchero wrote:You wont need the torx socket if you've got chrome bumpers. winkeye
Or some early facelifts. :wink:
Image

'88 e30 328i M52 track bint.
Ranchero
E30 Zone Addict
E30 Zone Addict
Posts: 2563
Joined: Thu Sep 17, 2009 11:00 pm

Post Wed Aug 24, 2011 8:53 pm

nickso wrote:
Ranchero wrote:They wouldn't have come out of the factory like that though, would they?
maybe not all the way down but certainly at the top.
That's what I mean.
Image
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Wed Aug 24, 2011 8:54 pm

Ranchero wrote:
nickso wrote:
Ranchero wrote:They wouldn't have come out of the factory like that though, would they?
maybe not all the way down but certainly at the top.
That's what I mean.
I can't remember to be honest. MIne leak so I need to do it better or further next time. :)
Image

'88 e30 328i M52 track bint.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Aug 25, 2011 3:13 pm

If it's an early facelift car, the two bumper bolts will be 10mm (IIRC) female hex. bolts. Later facelift use T55 torx.
The only sealant used on an E30 wing is the exposed bead, a couple of inches long, at the rear corner of the bonnet opening. A bit of seam sealer right at the back, at the lowest point, isn't a bad idea as well.