rolling road today

[ezagood]

should be interesting. place your bets. what bhp will i have.

[charlE30]

Good luck mate, what car's being tested?? and is there going to be a prize for the closest

[MurphyE30]

good luck. what car you running?

do you have an expected output?

[ezagood]

its a bored and stroked m20. no prizes sorry lol. i have a figure. just trying to upload a youtube vid then ill post the outcome. im happy with the result and i know there is more to come from the induction side of things.

[ezagood]

http://youtu.be/mx3LH7QEDA0
click the link to see it.
ended up with 212bhp

[e30-EVN]

This figure from a 2.7 m20??
I'd be happy with that mate, nice effort

[ezagood]

this is with air fuel ratio. runs richer at the top. ill do a maf conversion and see where it ends up

[ezagood]

This figure from a 2.7 m20??
I'd be happy with that mate, nice effort

thanks . its 2.9

[daimlerman]

Nice fiques!

What cam are you running,please?

What bore size and pistons?

[ezagood]

cam is 284/272 bore 85.5mm 84mm stroke

[mattqf77]

Very impressive. My dyno result was 166.1 bhp - standard M20 2.5 engine with no mods

[ezagood]

Very impressive. My dyno result was 166.1 bhp - standard M20 2.5 engine with no mods

not bad considering its age. only lost 4

[tonybtonyb]

Good news mate well done

[oguz327]

Nice figures there

What about torque? Is that 210 I can see?

[Simon13]

a 2.9?! thats making the same power as my 2.7

does it need mapping?

[ezagood]

a 2.9?! thats making the same power as my 2.7

does it need mapping?

yes. just got a £25 2.7 alpina replica chip. i ran out of money but ive got a trackday on tuesday and wanted to check it wasnt running lean. there is more to come

[ezagood]

Nice figures there

What about torque? Is that 210 I can see?

yeah 210

[bss325i]

135mm Rods, custom pistons and eta crank?

[ezagood]

yes yes and 84mm crank

[Duke137]

nice result jay, all that hard work paid off!

[ezagood]

thanks. yeah im happy with the power. feels quite strong and its only done 600 miles so once the maf conversion is done and its mapped propperly i recon it will be sweet. hopeing it holds together long enough to go down the strip at the bmw show. it keeps throwing up little probs for me to sort out like the heater matrix bursting friday night. i had to bypass the matrix so i could still go on the rollers on saturday.

[e30-EVN]

More to be had with a decent map or chip so it seems.... And maybey a maf conversion

[goosiegander]

Plenty of ponies there still to be harnessed dude!

Well done on the result, any progress toward the MAF conversion?

[ezagood]

i think im going to phone ant this week to sort it out.

[bss325i]

What exhaust manifold and system are you using?

Is the head standard other than the cam?

[ezagood]

btb manifold scorpion system ported head. sounds like this

[fowler]

from that vid is that oil smoke or dust ???? when you changed gear looked like a little puff of white smoke to me but we will see...
Regards to the MAF
Email ant if not PM details and i will pass them on......
Cheers
Ben

[DanThe]

Looks like blue smoke to me, good results so far though

[ezagood]

Yeah its burning oil. Stem seals I think. Bad on start up and trackdays but not noticable normally. They are new but patern parts. pisses me off but because it didnt smoke before the rebiuld. I might fix it next yr. I need to save my pennies for an emerald ecu