m50 time
Moderator: martauto
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
yes i agree you got any pictures of yours on here? I cant wait to do mine now! 
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
Search my name in the m50 section, my build thread is in there on page 2 or 3.
Haven't got any pics up of my car latley, been meaning to put em up lol
Haven't got any pics up of my car latley, been meaning to put em up lol
A 2 door e30 with 8 cylinders, what could be better

-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
right found a nice 525 touring picking it up on saturday so hopefully got my engine
full history and 130,000 on the clock also got all the other bits i think to do the swap apart from the clutch an 320 gear linkage so hopefully not long now!
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
Will need to swap out the PAS pump off the touring M50 if it has the self levelling rear suspension as the PAS pump will have an extra outlet on it.
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
yea i did remember this being said before just a e36 m50 one will do yea?
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
yep that's the kiddy.
With the problems that happen with the self-levelling rear suspension, many have been removed and replaced with srings & regular dampers, so the pump may have already been changed out.
Good thing with starting with an E34 donk is no time wasting hunting down sumps etc, just the engine mount arms from E36 to source
With the problems that happen with the self-levelling rear suspension, many have been removed and replaced with srings & regular dampers, so the pump may have already been changed out.
Good thing with starting with an E34 donk is no time wasting hunting down sumps etc, just the engine mount arms from E36 to source
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
yea that was the idea nice an easy
ive got my arms and m5 mounts so should be all sorted! may get danthe to do me a wiring loom tho as it looks a bit much for my wiring skills 
-
magpie
- Old Skooler

- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
have you gat the m20 gear linkage yet ?

m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
na still on the hunt for that do you no anyone with one? got to be 320 yea? im using a m42 box!
-
magpie
- Old Skooler

- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
pm en route m8


m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
without question, get your loom from Dan, engine loom and leccy fan loom.
If you haven't got exhaust manifold sorted yet then I would also look at getting those from him as the wiring and the exhaust is the single biggest pain with these swaps and Dan's products allow plug & play and they are bloody good quality too, not some chinese lash ups.
If you haven't got exhaust manifold sorted yet then I would also look at getting those from him as the wiring and the exhaust is the single biggest pain with these swaps and Dan's products allow plug & play and they are bloody good quality too, not some chinese lash ups.
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
yea i will send him a pm i think like you say thats the way to go!
i got some pas pipes off him for this swap and they are great quality!
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
With regards to the linkage- you can use either m20 items (2.0 or 2.5), on my setup I used my old m20 2.0 linkage set with m42 box.
Thing I found with it is the linkage yoke sits a bit forward of the hole in the tunnel, but by using a z3 1.9 short shifter rotated 180 degrees this problem is overcome!
If you haven't got a z3 shifter I suggest you get 1 mate, they are brill and noticably better! No more than £50 from bmw
I went up to see dan yesterday to pick up some parts and had a look at his chromie, the manifolds on his car look excellent and had I known before I would have seen him for sure! I will be getting him to do me a loom for my m52 as I had an electric fan loom off him for my current m50 and it works well and is made brilliantly
I would recommend him to any1
Thing I found with it is the linkage yoke sits a bit forward of the hole in the tunnel, but by using a z3 1.9 short shifter rotated 180 degrees this problem is overcome!
If you haven't got a z3 shifter I suggest you get 1 mate, they are brill and noticably better! No more than £50 from bmw
I went up to see dan yesterday to pick up some parts and had a look at his chromie, the manifolds on his car look excellent and had I known before I would have seen him for sure! I will be getting him to do me a loom for my m52 as I had an electric fan loom off him for my current m50 and it works well and is made brilliantly
I would recommend him to any1
A 2 door e30 with 8 cylinders, what could be better

-
Dezzy
- CR24v it's a lifestyle
- Posts: 11974
- Joined: Thu May 15, 2008 11:00 pm
- Location: Middlesbrough
Just get as much as you can off Danthe. It will be bang on then. I should know 

Co Founder of CR24vTM By Invitation Only. Absolutely no riff raff!!!
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
do i need to mod the heater pipes going into the matrix? 
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
nopeB15NAC wrote:do i need to mod the heater pipes going into the matrix?
the heater pipe that comes from the back of the head goes to the bottom pipe/stub, front heater pipe to the top stub on the bulkhead.
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
are good so thats easy then
just trying to think of stuff that i may not no about then get cought out on!
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
just trying to fit my servo and the 4 studs that hold it to the car wont reach through in to the car for me to get the nuts on? 
-
magpie
- Old Skooler

- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
have you put the pin in the linkage? take the pin out and get someone to push the servo on to the bulkhead while you do the nuts up


m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
thanks mick got it on but the servo doesnt work right!! its broken inside somewhere so need a new one!! 
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
If its clicking its because there is no resistance from the master cylinder, once you have the lines on and fluid in it will be fine
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
yea it like doesnt push straight an clicks when it goes so you think thats ok?
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Soon as you have the lines on and full of fluid it will change drastically
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
Yeah mine did the same and as dan said once it was all hooked up worked fine. Don't forget you need the resistance and vacuum for it to do its job 
A 2 door e30 with 8 cylinders, what could be better

-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
yea i will put it on tomorrow an i should be ok then! when it was clicking and not coming out straight i thought it was buggered!! 
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
got the servo on and working pedal bite seems low but they do work could i need a bigger spacer?
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
all sorted now and working well
first job done
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
the e34 i have bought is a auto! does thet make the wiring harder or does it make no odds? 
-
monkey
- E30 Zone Camper

- Posts: 1222
- Joined: Sat Jan 15, 2005 11:00 pm
- Location: devon
mine was an auto too , you can just cut all the auto bits out of the loomB15NAC wrote:the e34 i have bought is a auto! does thet make the wiring harder or does it make no odds?
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
are right cool thanks matt! just been looking at the wiring an it looks worryingly easy!
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
The wiring side of this conversion is harder thinking about than actually doing, if you get me?.... Lol
As I've told others, cut 1, join it, shrink and insulate, then move onto the next 1. Take your time with it and be thorough, its not overly difficult and quite satisfying once complete to be honest mate
As I've told others, cut 1, join it, shrink and insulate, then move onto the next 1. Take your time with it and be thorough, its not overly difficult and quite satisfying once complete to be honest mate
A 2 door e30 with 8 cylinders, what could be better

-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
so when you say cut the auto loom out is that going through all the loom and cutting away the auto side or can it stay just cut the plug off? 
-
monkey
- E30 Zone Camper

- Posts: 1222
- Joined: Sat Jan 15, 2005 11:00 pm
- Location: devon
just follow each wire from auto ecu plug and cut it out of the engine loom . it will make sense when you start .B15NAC wrote:so when you say cut the auto loom out is that going through all the loom and cutting away the auto side or can it stay just cut the plug off?
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
yea ok mat thanks for that also there was a little plug that fitted down by the ecu and it went inside the car down under the dash any idea what it is? it went into the loom maybe its part of the auto bit?!
-
B15NAC
- E30 Zone Regular

- Posts: 838
- Joined: Tue Oct 16, 2007 11:00 pm
- Location: devon/bovey tracey
well all bits got and engine ready
so the m42 is coming out on friday 
