what fan's are you lot using for 24v conversions.

Post Tue Jan 18, 2011 2:54 pm

i know i need a front mounted pusher fan.

will a 13" be too small?

what cars are your fans from?

cheers all...

Post Tue Jan 18, 2011 3:36 pm

E32 air-con fan....

Danthe can supply a suitable loom if you ask him properly,you will need either a radiator with a boss for the temp probe or do what I did and make up something like this;

Should be as close as possible to the radiator.

Post Tue Jan 18, 2011 4:49 pm

E34 aircon fan here to mate, fits perfectly in the space available

Post Tue Jan 18, 2011 4:58 pm

i have a danthe fan loom on the way and my rad has a 3 pin temp switch.

just got a resistor for twin speed

,just need to locate a fan hmm.

Post Tue Jan 18, 2011 5:01 pm

not any on ebay and none with a/c in my breakers

something else from a more easily sourced turd must be out there...???

Post Tue Jan 18, 2011 5:12 pm

there is a e34 on in my scrappy if you want it give me a shout

Post Tue Jan 18, 2011 5:17 pm

SHOUT!!! ^^

Post Tue Jan 18, 2011 5:24 pm

LOL

Post Tue Jan 18, 2011 5:27 pm

E36 16" twin speed electric fan,

Post Tue Jan 18, 2011 5:30 pm

do you have to remove the black plastic shroud for the e34 unit?

Paul that fan is bloody Huge

was it hard to mount?

Post Tue Jan 18, 2011 5:32 pm

The middle part of the fan where the motor is, is about a fag papers thickness from the front valance! It is awesome though. IIRC, one side was ok but the other side needed a small bracket to attach it.

Post Tue Jan 18, 2011 5:36 pm

was it a front mounted a/c fan from a 36 ?

Post Tue Jan 18, 2011 5:37 pm

I think it was yeah.

Post Tue Jan 18, 2011 5:49 pm

might be getting an e34 one and run it twin speed

been in touch with HKF about the one he knows of

Post Tue Jan 18, 2011 6:26 pm

The front mounted aircon fans were only on later E36's i think? Might be wrong though

Post Tue Jan 18, 2011 6:29 pm

6 pot E36's to be precise, most 4 pots tend to have a pull fan in the engine bay

Post Tue Jan 18, 2011 6:30 pm

DanThe wrote:6 pot E36's to be precise, most 4 pots tend to have a pull fan in the engine bay

That might be what I'm thinking of actually

Post Tue Jan 18, 2011 6:33 pm

just got this from Danthe.

a 13" pusher fan core mounted ,

i found a 13" fan i can do this with and it will only cost me a tenna.

update tomorrow when i get it,hopefully it will mount ok and nothing will be proud of the blades when i remove it

Post Tue Jan 18, 2011 8:03 pm

magpie wrote:just got this from Danthe.

a 13" pusher fan core mounted ,

i found a 13" fan i can do this with and it will only cost me a tenna.

update tomorrow when i get it,hopefully it will mount ok and nothing will be proud of the blades when i remove it

That's the one I was on about on the phone earlier Mick

Post Tue Jan 18, 2011 8:21 pm

E30BeemerLad wrote:
magpie wrote:just got this from Danthe.

a 13" pusher fan core mounted ,

i found a 13" fan i can do this with and it will only cost me a tenna.

update tomorrow when i get it,hopefully it will mount ok and nothing will be proud of the blades when i remove it
That's the one I was on about on the phone earlier Mick

looks a tidy job,that's monted with 10 mm bolts nylocks and rubber washers

i hope the one i've found is a goer .

Post Wed Jan 19, 2011 12:56 pm

paid a tenna total for both these parts

one flush fitting 13" pusher a/c fan and a large resistor for twin speed set up.

acquired fan from a hyundai people carrier and the hedgehog from a galant.

flush fit

hedghog has x2 wires to go to the fan and x3 wires at the other end to connect to a Danthe fan loom.

nice little mount bracket