Is this going to be difficult / expensive to fix?

Show off your pride and joy here

Moderator: martauto

User avatar
LowLevel
E30 Zone Newbie
E30 Zone Newbie
Posts: 119
Joined: Fri Jul 21, 2006 11:00 pm

Post Sat Jul 31, 2010 6:54 pm

Hi,

What do you think of this rust near the licence plate lights?

Is it especially ugly? Or should this not be too bad to fix?

Hopefully this won't have to be cut out and a replacement welded in....



Image

Image
-AJ
Kemix
E30 Zone Camper
E30 Zone Camper
Posts: 1423
Joined: Tue Jul 04, 2006 11:00 pm
Location: Braintree

Post Sat Jul 31, 2010 6:55 pm

source a new boot lid mate, easiest option 8)
.

Image
User avatar
LowLevel
E30 Zone Newbie
E30 Zone Newbie
Posts: 119
Joined: Fri Jul 21, 2006 11:00 pm

Post Sat Jul 31, 2010 6:57 pm

Kemix wrote:source a new boot lid mate, easiest option 8)
This is not part of the boot lid.

This is the two plastic lights that shine down onto the licence plate below.
-AJ
Kemix
E30 Zone Camper
E30 Zone Camper
Posts: 1423
Joined: Tue Jul 04, 2006 11:00 pm
Location: Braintree

Post Sat Jul 31, 2010 7:06 pm

sorry mate, wasn't thinking properly :o: I'm not so sure then, see what the others think 8)
.

Image
mattyb
E30 Zone Regular
E30 Zone Regular
Posts: 754
Joined: Sat Oct 06, 2007 11:00 pm
Location: gateshead

Post Sat Jul 31, 2010 8:11 pm

the rust does like its got a good hold there dude. the best way to repair it would be to cut it out. only way to ensure rust is gone. grinding back doesnt really work.
Image
iceox
E30 Zone Camper
E30 Zone Camper
Posts: 1147
Joined: Fri May 30, 2008 11:00 pm
Location: Scottish Borders

Post Sat Jul 31, 2010 8:48 pm

grind it back and if its totally clear metal then its fine, prime it and paint. if its still browny funny coloured, cut out and weld a patch in, not a hard job were that is, it would take 3-4 hours max
Image
Tommek
E30 Zone Newbie
E30 Zone Newbie
Posts: 218
Joined: Tue Oct 13, 2009 11:00 pm
Location: Romania

Post Sat Jul 31, 2010 8:52 pm

if it`s rusted from inside out the only way to repair it is to cut the affected zone and weld a patch. If it`s only surface rust at the outside, sand it till you see clean metal, apply a rust converter to secure any microscopic rust that may advance in time, prime it with an etch primer and the a top coat, and you`ll be good for a loong time.
E30 Touring
octanejunkie
E30 Zone Regular
E30 Zone Regular
Posts: 479
Joined: Fri Jul 02, 2010 11:00 pm
Location: Somerset England

Post Sun Aug 01, 2010 10:57 pm

Tommek wrote:if it`s rusted from inside out the only way to repair it is to cut the affected zone and weld a patch. If it`s only surface rust at the outside, sand it till you see clean metal, apply a rust converter to secure any microscopic rust that may advance in time, prime it with an etch primer and the a top coat, and you`ll be good for a loong time.

+1 :wink:
Blitz
Married to the E30 Zone
Married to the E30 Zone
Posts: 11151
Joined: Mon Jan 30, 2006 11:00 pm
Location: East London+Basildon

Post Sun Aug 01, 2010 10:59 pm

That looks like a hole by the looks of it.
Alex
Married to the E30 Zone
Married to the E30 Zone
Posts: 22665
Joined: Fri Feb 11, 2005 11:00 pm
Location: Johannesburg, South Africa

Post Sun Aug 01, 2010 11:04 pm

new metal is the only way to correctly cure the problem
Blitz
Married to the E30 Zone
Married to the E30 Zone
Posts: 11151
Joined: Mon Jan 30, 2006 11:00 pm
Location: East London+Basildon

Post Mon Aug 02, 2010 12:39 am

Are you from Nevada USA?
oldroydsr4
E30 Zone Squatter
E30 Zone Squatter
Posts: 1579
Joined: Tue Oct 25, 2005 11:00 pm
Location: Warwick

Post Mon Aug 02, 2010 1:39 pm

If you get a small screw driver and apply pressure at the area of corrosion, I would put money on that becoming a hole.
As the other have said cut outthe rust a weld in fresh metal.

While your working at the rear, check the reSt of the rear panel , I.e

Corners where it is welded to the rear quarters.
At the bottom near the towing eye.

If these 2 points are rotten, it mightbe best to put a new panel in.
User avatar
LowLevel
E30 Zone Newbie
E30 Zone Newbie
Posts: 119
Joined: Fri Jul 21, 2006 11:00 pm

Post Mon Aug 02, 2010 11:32 pm

Yes - looks like a hole, doesn't it?

How much labor / $$$ are we talking about to cut out and weld in a new replacement panel?

Will a repair like this last for a long time, or is it going to just start rotting out again...?
-AJ
gaszman
E30 Zone Meets/Events Team
E30 Zone Meets/Events Team
Posts: 3111
Joined: Wed Jan 03, 2007 11:00 pm
Location: Outside of Scummerland !

Post Sun Aug 08, 2010 9:51 am

i had a new pannel welded in they just get bigger untill the lights just hang down
Image
iceox
E30 Zone Camper
E30 Zone Camper
Posts: 1147
Joined: Fri May 30, 2008 11:00 pm
Location: Scottish Borders

Post Sun Aug 08, 2010 9:55 am

is thats the only bit of rust on the rear then just a patch will do, but check buy the towing eye and battery trays in the boot for more rust.

if its just a patch shouldnt cost more then 100 quid to get patched up then you'll have to respray on top of that, but that area isnt really visable, so i diy jobby should be fine :wink:
Image