Show off your pride and joy here
Moderator: martauto
-
LowLevel
- E30 Zone Newbie

- Posts: 119
- Joined: Fri Jul 21, 2006 11:00 pm
Post
Sat Jul 31, 2010 6:54 pm
Hi,
What do you think of this rust near the licence plate lights?
Is it especially ugly? Or should this not be too bad to fix?
Hopefully this won't have to be cut out and a replacement welded in....

-AJ
-
Kemix
- E30 Zone Camper

- Posts: 1423
- Joined: Tue Jul 04, 2006 11:00 pm
- Location: Braintree
Post
Sat Jul 31, 2010 6:55 pm
source a new boot lid mate, easiest option

.

-
LowLevel
- E30 Zone Newbie

- Posts: 119
- Joined: Fri Jul 21, 2006 11:00 pm
Post
Sat Jul 31, 2010 6:57 pm
Kemix wrote:source a new boot lid mate, easiest option

This is not part of the boot lid.
This is the two plastic lights that shine down onto the licence plate below.
-AJ
-
Kemix
- E30 Zone Camper

- Posts: 1423
- Joined: Tue Jul 04, 2006 11:00 pm
- Location: Braintree
Post
Sat Jul 31, 2010 7:06 pm
sorry mate, wasn't thinking properly

I'm not so sure then, see what the others think

.

-
mattyb
- E30 Zone Regular

- Posts: 754
- Joined: Sat Oct 06, 2007 11:00 pm
- Location: gateshead
Post
Sat Jul 31, 2010 8:11 pm
the rust does like its got a good hold there dude. the best way to repair it would be to cut it out. only way to ensure rust is gone. grinding back doesnt really work.
-
iceox
- E30 Zone Camper

- Posts: 1147
- Joined: Fri May 30, 2008 11:00 pm
- Location: Scottish Borders
Post
Sat Jul 31, 2010 8:48 pm
grind it back and if its totally clear metal then its fine, prime it and paint. if its still browny funny coloured, cut out and weld a patch in, not a hard job were that is, it would take 3-4 hours max
-
Tommek
- E30 Zone Newbie

- Posts: 218
- Joined: Tue Oct 13, 2009 11:00 pm
- Location: Romania
Post
Sat Jul 31, 2010 8:52 pm
if it`s rusted from inside out the only way to repair it is to cut the affected zone and weld a patch. If it`s only surface rust at the outside, sand it till you see clean metal, apply a rust converter to secure any microscopic rust that may advance in time, prime it with an etch primer and the a top coat, and you`ll be good for a loong time.
E30 Touring
-
octanejunkie
- E30 Zone Regular

- Posts: 479
- Joined: Fri Jul 02, 2010 11:00 pm
- Location: Somerset England
Post
Sun Aug 01, 2010 10:57 pm
Tommek wrote:if it`s rusted from inside out the only way to repair it is to cut the affected zone and weld a patch. If it`s only surface rust at the outside, sand it till you see clean metal, apply a rust converter to secure any microscopic rust that may advance in time, prime it with an etch primer and the a top coat, and you`ll be good for a loong time.
+1

-
Blitz
- Married to the E30 Zone

- Posts: 11151
- Joined: Mon Jan 30, 2006 11:00 pm
- Location: East London+Basildon
Post
Sun Aug 01, 2010 10:59 pm
That looks like a hole by the looks of it.
-
Alex
- Married to the E30 Zone

- Posts: 22665
- Joined: Fri Feb 11, 2005 11:00 pm
- Location: Johannesburg, South Africa
Post
Sun Aug 01, 2010 11:04 pm
new metal is the only way to correctly cure the problem
-
Blitz
- Married to the E30 Zone

- Posts: 11151
- Joined: Mon Jan 30, 2006 11:00 pm
- Location: East London+Basildon
Post
Mon Aug 02, 2010 12:39 am
Are you from Nevada USA?
-
oldroydsr4
- E30 Zone Squatter

- Posts: 1579
- Joined: Tue Oct 25, 2005 11:00 pm
- Location: Warwick
Post
Mon Aug 02, 2010 1:39 pm
If you get a small screw driver and apply pressure at the area of corrosion, I would put money on that becoming a hole.
As the other have said cut outthe rust a weld in fresh metal.
While your working at the rear, check the reSt of the rear panel , I.e
Corners where it is welded to the rear quarters.
At the bottom near the towing eye.
If these 2 points are rotten, it mightbe best to put a new panel in.
-
LowLevel
- E30 Zone Newbie

- Posts: 119
- Joined: Fri Jul 21, 2006 11:00 pm
Post
Mon Aug 02, 2010 11:32 pm
Yes - looks like a hole, doesn't it?
How much labor / $$$ are we talking about to cut out and weld in a new replacement panel?
Will a repair like this last for a long time, or is it going to just start rotting out again...?
-AJ
-
gaszman
- E30 Zone Meets/Events Team

- Posts: 3111
- Joined: Wed Jan 03, 2007 11:00 pm
- Location: Outside of Scummerland !
Post
Sun Aug 08, 2010 9:51 am
i had a new pannel welded in they just get bigger untill the lights just hang down
-
iceox
- E30 Zone Camper

- Posts: 1147
- Joined: Fri May 30, 2008 11:00 pm
- Location: Scottish Borders
Post
Sun Aug 08, 2010 9:55 am
is thats the only bit of rust on the rear then just a patch will do, but check buy the towing eye and battery trays in the boot for more rust.
if its just a patch shouldnt cost more then 100 quid to get patched up then you'll have to respray on top of that, but that area isnt really visable, so i diy jobby should be fine
