How to, drain, cleanse, refill and remove air from m20? help

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
mattrs
E30 Zone Squatter
E30 Zone Squatter
Posts: 1810
Joined: Fri Apr 18, 2008 11:00 pm

Post Tue Jul 27, 2010 4:46 pm

As above really. What chemical to use? Also what sort of ratio antifreeze to water?

I have left my haynes manual round my girlfriends :o:

Any advice/tips would be appreciated.

Cheers :D
User avatar
mattrs
E30 Zone Squatter
E30 Zone Squatter
Posts: 1810
Joined: Fri Apr 18, 2008 11:00 pm

Post Tue Jul 27, 2010 5:03 pm

Anyone?
User avatar
mattrs
E30 Zone Squatter
E30 Zone Squatter
Posts: 1810
Joined: Fri Apr 18, 2008 11:00 pm

Post Tue Jul 27, 2010 5:20 pm

????????????
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Tue Jul 27, 2010 5:22 pm

Bet your g/f is enjoying her bedtime reading!
I have only used water to flush the system out,although others swear by traffic film remover.
I use 1 measure of antifreeze to 2 of water,using a litre measuring jug 'borrowed' from the kitchen.
Pour in slowly,to let the fluid settle and push the air out.Have the bleed nipple on the thermostat housing slackened off.When the system appears to be full,set the heater to maximum heat and run the engine at idle with the pressure cap fitted.When coolant is dribbling from the bleed point with no air bubbles and the heater is producing hot air,you are done,tighten up the bleed screw,let the engine cool and check the level in the expansion tank.
I find that my M20 prefers to be a little under the full mark,so do not worry if it settles a bit low.
Youth is wasted on the young.
User avatar
mattrs
E30 Zone Squatter
E30 Zone Squatter
Posts: 1810
Joined: Fri Apr 18, 2008 11:00 pm

Post Tue Jul 27, 2010 5:25 pm

Top man! Thanks.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jul 27, 2010 9:43 pm

To add to Daimlerman's post: When you start the engine, set the heater control to full hot, the fan to '2', the top two sliders to the left and the bottom slider to the right. Monitor the air coming from the heater into the footwell, and ensure that it has the beginnings of warmth within a couple of minutes of starting the engine. Also keep a close eye on the temperature gauge.
If not warm air is forthcoming, and the gauge is climbing, you have an airlock in the head, and if the M20 is a 2.5, you are in danger of cracking the head.
The airlock can be cleared by removing the top heater hose at the bulkhead, placing your hand flat across the coolant bottle filler neck, and blowing gently into the overflow hose, until coolant flows both from the hose and the heater stub.
User avatar
mattrs
E30 Zone Squatter
E30 Zone Squatter
Posts: 1810
Joined: Fri Apr 18, 2008 11:00 pm

Post Tue Jul 27, 2010 11:10 pm

Cheers guys
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Fri Sep 23, 2011 9:40 pm

is it true you can not useenought anti freeze it does no damage to engine
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Sep 23, 2011 10:17 pm

threelander wrote:is it true you can not useenought anti freeze it does no damage to engine
?? Does that say use enough antifreeze or use nought antifreeze?
If you use no antifreeze you will cause damage to the engine by corrosion in a surprisingly short time. On a M20 this usually takes the form of the crescent shaped waterways around the chambers in the head corroding back under the fire ring in the head gasket.
Excess antifreeze reduces the efficieny of the cooling system.
Recommended concentration is 33% - 50%.