The tax runs out on the 325 at the end of October, I'll pull it off the road for the winter and get it all done then hopefully.
An M30 swap/general playing with E30 scrap thread
Moderator: martauto
Still a few things to do to the motor before it goes in. I need to tidy the bombsite that is my garage and get cracking!
The tax runs out on the 325 at the end of October, I'll pull it off the road for the winter and get it all done then hopefully.
The tax runs out on the 325 at the end of October, I'll pull it off the road for the winter and get it all done then hopefully.
-
gareth
- E30 Zone Team Member
- Posts: 11009
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
this is the cheapest i've seen a M30 clutch. beware though, depending on the year there are two clutch part numbers. one for the E28 flywheel. one for the E32/34 dual mass flywheel.
http://www.e30zone.net/modules.php?name ... m30+clutch
http://www.e30zone.net/modules.php?name ... m30+clutch
Sole founder of Fe2O3-12V it's a lifestyle
LSD rebuilding / modification services provided, PM for details
LSD rebuilding / modification services provided, PM for details
-
cliffybabe
- Powered by Nelly
- Posts: 10020
- Joined: Sun Dec 18, 2005 11:00 pm
- Location: Croydon
Dude the boot lid of the black one, what condition is it in?>?? Its flat schwarzt isnt it??
Considering Selling the Cabby, looks like its gonna go
Just not the right time... 
-
Rav335uk
- E30 Zone Meets/Events Team
- Posts: 27985
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
- Contact:
NOOOOOOOOOOOOOOOOOO!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Mate you had everything, so near , i read the other post, shame rally but work comes first
Mate you had everything, so near , i read the other post, shame rally but work comes first
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
leeparkes
- Married to the E30 Zone
- Posts: 9538
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
You could sell your arseE30Gheko wrote:Rav, gutted is not the word. I need to raise some funds and I can't sell the children!
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
Rav335uk
- E30 Zone Meets/Events Team
- Posts: 27985
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
- Contact:
leeparkes wrote:You could sell your arseE30Gheko wrote:Rav, gutted is not the word. I need to raise some funds and I can't sell the children!
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
Hold on hold on. I still got an M30 AND after today's little morning meeting I STILL HAVE A RESTAURANT TO RUN with a rather big lifeline been handed to me.... 
I must have done something they liked.
The fat lady has certainly been warming up her tonsils but she hasn't broken into song just yet!!
I must have done something they liked.
The fat lady has certainly been warming up her tonsils but she hasn't broken into song just yet!!
Good stuff man! - Woohoo! -
DanThe
- E30 Zone Team Member
- Posts: 28641
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
- Contact:
You knew I wanted them though! Nevermind, the nasty bits will be replaced and if I ever sell them on I will give you a shoutE30Gheko wrote:It might be a bit uncomfortable though now! Not to worry though... I'll get the thing running first and then worry about what I'm going to sit on!DanThe wrote:
Right I'd better get my finger out then eh?
Almost all parts have been sourced. The one bit that has got me scratching my head is the 320i gear linkage that I apparently need. Anyone got a picture of one of these or better still does anyone have one?
I'm planning on taking this to bits at the next available opportunity...
I might be able to get this done on Saturday cos I can get cover at work easily on a Saturday. I'm just waiting to hear if I can borrow the ramps again.
I'm planning on keeping most of the bits from it including the engine. The leftovers are heading for the crusher..
Almost all parts have been sourced. The one bit that has got me scratching my head is the 320i gear linkage that I apparently need. Anyone got a picture of one of these or better still does anyone have one?
I'm planning on taking this to bits at the next available opportunity...
I might be able to get this done on Saturday cos I can get cover at work easily on a Saturday. I'm just waiting to hear if I can borrow the ramps again.
I'm planning on keeping most of the bits from it including the engine. The leftovers are heading for the crusher..
