Gheko's 318i rust repairs. updated

Show off your pride and joy here

Moderator: martauto

E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Mon May 18, 2009 10:10 pm

With the 325 nearing a state of semi-completion and requiring just a tax disc to be fully road legal, I decided today to strip the 318i and go on a rust hunt. My search was not to be in vain....

First out were the boot carpets. Revealing a few bits here and there but it's not in too bad shape. There's a patch been welded before which has a lot of surface rust but it's still solid enough...
Image
Slightly more concerning was this bit around where the fuel filler pipe exits the rear of the boot area...
Image

And another bit on the outer inner wing...
Image

Then out came the rear door cards to see what was behind this bit of rust on the outer arch..
Image

Lo and behold...
Image
This is not half as bad as the arches on the 325 which I managed to get repaired so I was still feeling quite chuffed with just one or two bits of easily repairable stuff.

Next out was the carpets. They were a bit damp and stained so I fully expected to find some floor panel issues.....

Image

I removed the dreaded mudflaps a little while ago only to rip a sizeable hole in the nearside lower wing... After removing the front wings the holes just kept getting bigger, and bigger.. :(

Nearside...
Image

Image

Offside, not quite as extensive, but pretty bad all the same...
Image

Image

Now normally when I have read threads like this before, at this point there usually follows the question, 'should I frag it or should I restore it???'

Well, despite the fact that this is a lowly bog standard M40 I am still going to attempt to save it, because,

1. All of the mechanicals/brakes/electrics etc are A1
2. It's a dolphin grey 2 door with no sunroof
3. My nephew can get the use of it in it's current set up for a bit after passing his test
4. Once the shell's integrity has been restored, and the boy has got his own motor, I'd like to tackle an M50 conversion. This would be an ideal lightweight shell for such a project.

So having decided to save this one, the question is how? The two big holes around the jacking points are obviously going to be the most difficult to sort.

I've never done any welding before but I'm about to learn I think. It's been something I've wanted to try for a long time and I think I have myself a guinea pig!! winkeye
Last edited by E30Gheko on Mon Jun 29, 2009 6:46 pm, edited 1 time in total.
madaboutthe30
E30 Zone Camper
E30 Zone Camper
Posts: 1391
Joined: Sun Oct 21, 2007 11:00 pm
Location: Stanmore, Harrow

Post Mon May 18, 2009 10:15 pm

I admire you braveness.

When it comes to welding the only advise I could give you is to find a metal sheet somewhere and practise and practise.

It took us loads of practises before we got it right and actually started on the car.
Dreaming of the day I purchase an E30 M3

--- e30 motorsport cab-- in the process of becoming a trailer queen
--- Z4M Coupe - daily driver
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Mon May 18, 2009 10:20 pm

madaboutthe30 wrote:I admire you braveness.

When it comes to welding the only advise I could give you is to find a metal sheet somewhere and practise and practise.

It took us loads of practises before we got it right and actually started on the car.
Why thankyou. I anticipate welding is a skill that is not going to come easy!
skipunda
E30 Zone Team Member
E30 Zone Team Member
Posts: 5672
Joined: Thu Sep 04, 2008 11:00 pm
Location: Cornwall/Plymouth

Post Mon May 18, 2009 10:51 pm

proper job, gheko!
nice thread title by the way
Chris
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Tue May 19, 2009 12:24 am

Good luck with the welding dude, im sure ur crack it
Image
Considering Selling the Cabby, looks like its gonna go
e30topless
E30 Zone Team Member
E30 Zone Team Member
Posts: 13595
Joined: Wed Aug 23, 2006 11:00 pm
Location: surrounded by scrap

Post Tue May 19, 2009 12:27 am

:eek: that is far far worse than the rust I found on my red 2 door it makes me feel picky

good luck with the welding rob plenty of practise there :)
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 12:32 am

Cheers guys!

I know it looks quite bad doesn't it? I'm always inclined to look on the positive side of things though and the bits that aren't photographed are all very tidy! :chuckle:

Seriously though, welding is something I want to know how to do so if I can manage to sort this mess out then I should be well on my way to aquiring a new skill. :thumb:
Daf318is
E30 Zone Camper
E30 Zone Camper
Posts: 1260
Joined: Mon Jul 30, 2007 11:00 pm
Location: North Wales (Denbighshire)

Post Tue May 19, 2009 2:07 pm

1 tip with welding - don't leave your phone on the same workbench. They tend to end up full of holes otherwise! :o:
Image
Now driving an E46 320D touring :(, but it get's worse..... the new project is going to be Ford powered!
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 2:17 pm

Daf318is wrote:1 tip with welding - don't leave your phone on the same workbench. They tend to end up full of holes otherwise! :o:
:lol:

You sound like a man speaking from experience!

The guy that welded up the 325 actually set a customers car on fire whilst welding when he was a lot younger. He had to get it off ramps when it was completely engulfed to prevent the cars either side from going on fire too!

I'll have to get the boy to fire watch and arm him with several fire extinguishers!
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Tue May 19, 2009 2:34 pm

E30Gheko wrote:
Daf318is wrote:The guy that welded up the 325 actually set a customers car on fire whilst welding when he was a lot younger. He had to get it off ramps when it was completely engulfed to prevent the cars either side from going on fire too!
the garage i used to work in when i left school set fire to 635i and an mgb in seperate welding incidents. :D i got a bollocking for not noticing the 635 going up as i was sitting in it lol.

some nasty rust there, have you checked the bulkhead above the glovebox? that could be very nasty judging by the rest of it. the petrol breather pipe looks like a mare to fix properly.
Image

'88 e30 328i M52 track bint.
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 2:42 pm

Bulkhead is fine. Agree the petrol breather pipe looks a nightmare. Possibly trickier than the rather large holes. I may even re-route it! Would it be easier to put in a new filler cap behind the numberplate?
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Tue May 19, 2009 6:35 pm

remember that isnt the fuel filler pipe. its the pipe that transfers the three breather pipes from the tank to the breather bottle in the wheel arch.

i looked at how to repair this when i was doing various welds on mine. the only way i could see was to chop the pipe in the cabin, cut the rot out of the arch and then fab up an entire new plate and pipe in one piece, then weld it all up at the same time in situ. this is all assuming there is no way of getting the original piece from BMW and cutting it to suit.
Image

'88 e30 328i M52 track bint.
Alex
Married to the E30 Zone
Married to the E30 Zone
Posts: 22665
Joined: Fri Feb 11, 2005 11:00 pm
Location: Johannesburg, South Africa

Post Tue May 19, 2009 6:40 pm

good luck with it gheko, i think ive scrapped better :o: winkeye

will be worth it after as it will be A1 :)
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 6:50 pm

Alex wrote:good luck with it gheko, i think ive scrapped better :o: winkeye

will be worth it after as it will be A1 :)
TBH it probably should get scrapped, but I'm on a mission! God alone knows why I'd want to save this turd but I'm still going ot give it a go!

This fuel filler pipe is starting to cause me grave concern though.

Nickso, did u actually manage to fix yours that way or is that just how you figured you would do it if you were going to fix it?
A1BMW325iSport
E30 Zone Addict
E30 Zone Addict
Posts: 4239
Joined: Mon Jan 10, 2005 11:00 pm
Location: Mid Wales

Post Tue May 19, 2009 6:51 pm

good luck with it, keep us posted with the work
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Tue May 19, 2009 6:57 pm

E30Gheko wrote: TBH it probably should get scrapped, but I'm on a mission! God alone knows why I'd want to save this turd but I'm still going ot give it a go!

This fuel filler pipe is starting to cause me grave concern though.

Nickso, did u actually manage to fix yours that way or is that just how you figured you would do it if you were going to fix it?
no mine was just good enough to clean up and paint over and hopefully it wont get any worse. i reckon if i had found that on mine i would have just looked for another shell, if it goes on mine now ill probably just cut my losses.

my bulkhead was bad though and like you i was on a mission to save it no matter what, TBH if i was buying another e30 and found the kind of rot my current one had i would walk away. its taken me almoat a year to completely de-rust the car.....time i could have spent driving the bloody thing.
Image

'88 e30 328i M52 track bint.
Alex
Married to the E30 Zone
Married to the E30 Zone
Posts: 22665
Joined: Fri Feb 11, 2005 11:00 pm
Location: Johannesburg, South Africa

Post Tue May 19, 2009 7:00 pm

E30Gheko wrote:
Alex wrote:good luck with it gheko, i think ive scrapped better :o: winkeye

will be worth it after as it will be A1 :)
TBH it probably should get scrapped, but I'm on a mission! God alone knows why I'd want to save this turd but I'm still going ot give it a go!

This fuel filler pipe is starting to cause me grave concern though.

Nickso, did u actually manage to fix yours that way or is that just how you figured you would do it if you were going to fix it?
any e30 saved is good in my books winkeye
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue May 19, 2009 7:12 pm

Your rust troubles are almost as bad as mine. I'm gradually fighting my way through the repairs, but as I finish one bit I find more rot elsewhere. I ain't giving up now though, and I might just get the car finished before the summer is over.

Keep at it, and remember it often looks worse than it is.

I'm sure somebody has said on here before that if folk keep fragging their E30s at the first sign of rust, before long there won't be any shells left.
rust never sleeps
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 7:15 pm

nickso wrote:
E30Gheko wrote: TBH it probably should get scrapped, but I'm on a mission! God alone knows why I'd want to save this turd but I'm still going ot give it a go!

This fuel filler pipe is starting to cause me grave concern though.

Nickso, did u actually manage to fix yours that way or is that just how you figured you would do it if you were going to fix it?
no mine was just good enough to clean up and paint over and hopefully it wont get any worse. i reckon if i had found that on mine i would have just looked for another shell, if it goes on mine now ill probably just cut my losses.

my bulkhead was bad though and like you i was on a mission to save it no matter what, TBH if i was buying another e30 and found the kind of rot my current one had i would walk away. its taken me almoat a year to completely de-rust the car.....time i could have spent driving the bloody thing.
I know what you mean! I have another E30 which I'm driving at the moment, although that's not without it's share of problems either!

I'm swithering now whether to cut my losses with this one but I've been saying for a while that I want to learn how to weld so I can't imagine a better car to 'have a go' on. If I get half way through and decide it's not worth it I can always sell the good bits and I shouldn't be out of pocket.

I think the first thing to tackle should be this pipe. Atleast then if it turns out to be impossible I haven't wasted any time doing the big holes which will probably be easier to sort. At least I can get to them easy enough.
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Tue May 19, 2009 7:29 pm

E30Gheko wrote: I know what you mean! I have another E30 which I'm driving at the moment, although that's not without it's share of problems either!

I'm swithering now whether to cut my losses with this one but I've been saying for a while that I want to learn how to weld so I can't imagine a better car to 'have a go' on. If I get half way through and decide it's not worth it I can always sell the good bits and I shouldn't be out of pocket.

I think the first thing to tackle should be this pipe. Atleast then if it turns out to be impossible I haven't wasted any time doing the big holes which will probably be easier to sort. At least I can get to them easy enough.
that was exactly what happened with mine, found out it was a rotter and thought i'd have a go at fixing it. it's only a track car so it doesnt have to be very pretty as long as it doesn't5 fall apart at 100mph on the track :o

my welding has gone from fucking awful to not bad at all.

you might as well have a go on the pipe, it will only be a scrapper anyway if you fail.

mine is almost completely rust free and if it stays that way for a few years before it gets bad again ill be happy enough.
Image

'88 e30 328i M52 track bint.
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 7:35 pm

I'll have to give it a go Nickso! Would this pipe HAVE to be metal? I mean could I cut the pipe where it's good and then replace it with a rubber one?
Blitz
Married to the E30 Zone
Married to the E30 Zone
Posts: 11151
Joined: Mon Jan 30, 2006 11:00 pm
Location: East London+Basildon

Post Tue May 19, 2009 7:36 pm

After you have got rid of the rust at least you know that its truly rust free E30.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue May 19, 2009 7:50 pm

Have you checked out the scuttle drains? Rot here and you wont want to be saving it. Look through the box section on the N/S inner wing
The footwells are easy, rear inner arches will be the worst job on yours
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Tue May 19, 2009 7:50 pm

E30Gheko wrote:I'll have to give it a go Nickso! Would this pipe HAVE to be metal? I mean could I cut the pipe where it's good and then replace it with a rubber one?
i dont know TBH, i guess the only reason its metal is because it needs to be rigid to avoid damage to the breather pipes when the back seat is in place.
Image

'88 e30 328i M52 track bint.
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 7:58 pm

Ok fair enough. What about if it was replaced with a rubber one with some sort of metal 'support' welded over the top? I could see something like that making the job a bit easier. I mean, how could you weld around a hole pipe if you can only get to one side of it?

Do you know of any pictures anywhere of the pipe fully exposed?
Ollie_bwoii
Married to the E30 Zone
Married to the E30 Zone
Posts: 8695
Joined: Sat May 17, 2008 11:00 pm
Location: Northampton

Post Tue May 19, 2009 7:59 pm

Your E30 looked clean at first! Such a shame! :(

Not sure I want to look at my chromie now!
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Tue May 19, 2009 8:03 pm

E30Gheko wrote:Ok fair enough. What about if it was replaced with a rubber one with some sort of metal 'support' welded over the top? I could see something like that making the job a bit easier. I mean, how could you weld around a hole pipe if you can only get to one side of it?

Do you know of any pictures anywhere of the pipe fully exposed?
good point about not being able to weld it all the way round, guess you would have to clampa sleeve round it instead.

what do you mean by fully exposed? inside the cabin or in the wheel arch?
Image

'88 e30 328i M52 track bint.
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 8:06 pm

Well I can see where the pipe goes through the cabin and then emerges in the boot which is where it's rusted, but where does it go after it disappears behind the arch again?

DanThe, I'm going to look at the scuttle drains right now!
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue May 19, 2009 8:20 pm

It comes down under the rear seat and then through the floor next to the fuel pump hatch, wouldnt be difficult at all IMO, no need for rubber pipe, id just go to the scrap yard with a hammer and bolster chisel :)
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 8:35 pm

well the good news is that the scuttle drains are clean as a whistle. That's the strange thing about this car really. The bits which aren't rusty are very clean! Some bits still look absolutely brand new.

OK re the pipe: the bit under the seat is fine, so I assume (although I haven't looked yet) that the bit under the hatch will be OK too. The only rusty bit is the little bit of the same pipe you can see just behind the seat in the boot.
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Tue May 19, 2009 9:11 pm

A really friendly welder has just come into our restaurant and has offered to do all the work! I took him over to view the turd. As keen as I am to learn I suppose it will come down to what's more cost effective, buying a welder or paying this guy to do it for me?

I would guess the former. However he has asked me to leave it with him and he will give me an idea on price after he's had time to think about it.


I'm just gonna buy him a beer. winkeye
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Wed May 20, 2009 10:18 am

He turned out to be a really nice bloke this welder dude. He is in his 40's and has been welding all day every day since he was 15. He was asked to teach welding at the local college. I think I may have found the man for the job!
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Mon Jun 29, 2009 12:32 pm

Just back from visiting my welder. He said he is probably going to have it finished this afternoon. If I said I was impressed with what he has done so far, that would be understatement of the year! The guy is a welding God! I'm popping back to his place this afternoon, so I shall take some pics of what he's done and post them up later.

If anyone has similar repairs required I can really recommend this fella! :D
ImysE30
Married to the E30 Zone
Married to the E30 Zone
Posts: 22478
Joined: Mon Jul 07, 2008 11:00 pm
Location: Derby Massive!!

Post Mon Jun 29, 2009 4:27 pm

Good news Rob, look forward to the update pic's :cool:
Current Fleet:

E30 335i Turbo M3 Convertible Replica
E30Gheko
E30 Zone Addict
E30 Zone Addict
Posts: 3789
Joined: Sun Sep 28, 2008 11:00 pm
Location: Wirral

Post Mon Jun 29, 2009 6:37 pm

Right got some pics,

From this,
Image
to this
Image
and this,
Image
to this
Image
Image
before
Image

after
Image

Still a bit to go, not quite finished yet.

He said he'll find somewhere to leave it too until I get time to get down there for a good undersealing session with the use of his ramps. :D