Bulkhead Repairs

Show off your pride and joy here

Moderator: martauto

MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Feb 10, 2009 2:57 pm

Thought I'd stick up a few pictures of the butchery I'm doing to my car. The shell was in generally good contition with the exception of the battery tray area, which turned out to be a bit worse than I originally thought.

Was hoping it'd need just a couple of plates welded in to patch the rusty holes:

Image

After some poking around and removal of the pedals it was clear that it was a bit worse:

Image

Image

Image

Image

So after getting in about it with various cutting tools it now looks like this:

Image

There are a couple more small bits to cut out from the inside, its getting a bit tight for space though. Any more and I'd have had to move the dash, loom and probably the engine - No thanks!

Going to finish the cutting this weekend and hopefully find time to fabricate some bits to get welded in.

I'd welcome some useful comments. I've already been told that I'm insane, wasting my time and should have re-shelled it.
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Tue Feb 10, 2009 3:53 pm

Brave man ! Looks like you got it all though - and lets face it most of the repair area won't be visible as it will be hidden by the battery when its all back together - Id just be sure to put a nice thick coating of hammerite on the repair followed by some waxoyl to stop it coming back. Good job mate - look forward to seeing the finished work ! 8)
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Feb 10, 2009 4:02 pm

Thanks rob,

I'll be approaching a bit of the welding from the inside of the arch. I've removed some patches of the thick PU joint sealing rubber stuff that is smeared on a lot of the welded areas. What is the best thing to use to replace this stuff. Would a good dose of waxoyl and underseal spray do the job?
rust never sleeps
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Tue Feb 10, 2009 4:05 pm

What caused that to go so badly - a leaking battery i guess...

Top marks for going to such efforts at this time of year, oop North too :notworthy:
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
Dan320is
E30 Zone Squatter
E30 Zone Squatter
Posts: 1813
Joined: Wed Jan 12, 2005 11:00 pm
Location: Cambridgeshire

Post Tue Feb 10, 2009 4:33 pm

Have a gander at my touring project thread, you can see how I sealed the new joints/welds etc.

http://www.e30zone.net/modules.php?name ... c&t=116241
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Feb 10, 2009 4:34 pm

No idea, I bought it back in October. The PO said it had been sitting on the driveway for a few months. I guess it just went unnoticed for a while and the rust started munching. I'm sure somebody else on here must've had similar happen to their E30?

There are a few other small areas I'd like to patch up. If this repair is a success the other work will seem like a walk in the park. It is a lot more than I was expecting to do when I bought the car.
rust never sleeps
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Feb 10, 2009 4:38 pm

Need to type faster..

Thanks Dan, I'll have a read.
rust never sleeps
User avatar
gooner1
Out humping Reindeer
Posts: 13280
Joined: Fri Apr 14, 2006 11:00 pm
Location: Northampton.For my sins.

Post Tue Feb 10, 2009 4:40 pm

Fair play MrWhite, a lot of cars have been scrapped for less than that.
While i,m here, iv,e recently noticed a very small amount of surface rust on my battery tray.
Nothing to worry about, will rub it down, etch prime and then spray it, but would it be worth drilling a few drai holes in it before i do?.
Image
Dan320is
E30 Zone Squatter
E30 Zone Squatter
Posts: 1813
Joined: Wed Jan 12, 2005 11:00 pm
Location: Cambridgeshire

Post Tue Feb 10, 2009 4:48 pm

gooner1 wrote:Fair play MrWhite, a lot of cars have been scrapped for less than that.
While i,m here, iv,e recently noticed a very small amount of surface rust on my battery tray.
Nothing to worry about, will rub it down, etch prime and then spray it, but would it be worth drilling a few drai holes in it before i do?.
Give it a stab and a scrape with a screwdriver :eek:
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Feb 10, 2009 5:03 pm

The thing I've found most difficult with this job is having to work around the equipment in the car. I'm running out of space to keep all the bits I take off to get to the rusty bits.

It was oh so close to becoming a seriously big/impossible job... you can see how near I've had to get to the main loom and its still touch and go as to whether I can finish this fix without having to remove the dash.

Also, the last little bit of rust can only really be cut out from inside the car as the back of the engine is in the way, as can be seen in these pictures:

Image

It has been rather crudely covered in black silicone at some point (obviously leaking in the past). Not a good fix methinks.

Image

You can see it in the far right of this picture

Image

There is another little bad bit just where the inner wing (from the strut) meets the bulkhead.
rust never sleeps
ricey46
E30 Zone Regular
E30 Zone Regular
Posts: 982
Joined: Fri Dec 02, 2005 11:00 pm
Location: Edinburgh

Post Tue Feb 10, 2009 5:09 pm

Fair play to you, glad you're fixing it!! :cool:
Paul.
325i sport Tech1
335i Chromie - Sold
2001 E46 M3-Sold
1999 E39 M5

Image
leeparkes
Married to the E30 Zone
Married to the E30 Zone
Posts: 9535
Joined: Thu Jan 03, 2008 11:00 pm
Location: Black country

Post Tue Feb 10, 2009 5:44 pm

Fight the rust :guns:
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place.. :o:
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Feb 10, 2009 7:09 pm

On a side note - one of the rear jacking points (OS I think) is a bit rotten. Is it best to try to cut away rust and patch the holes or to chop a whole jacking point off another shell and fit that>?

Suppose it depends how bad the rust is.
rust never sleeps
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Mar 10, 2009 1:54 pm

An update from last weekend.

All the rust cut out ready for welding:
Image

Image

First plate in place:

Image

And the rest....

Image

Image

Image

Image

A generous application of seam sealer:

Image

Followed by zinc primer:

Image

Image

Now its ready for a top coat of some kind. I doubt that I'm going to spank loads of cash on brilliant red paint, I think it'll end up black instead. Still to fabricate the battery tray, from ally. It will be bolted in so it can be removed if required.

Progress! Next cut-n-weld job will be the jacking points, they are far from good.
rust never sleeps
ricey46
E30 Zone Regular
E30 Zone Regular
Posts: 982
Joined: Fri Dec 02, 2005 11:00 pm
Location: Edinburgh

Post Tue Mar 10, 2009 3:24 pm

Good effort with the welding, looks a cracking job :cool:
Paul.
325i sport Tech1
335i Chromie - Sold
2001 E46 M3-Sold
1999 E39 M5

Image
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Mar 10, 2009 4:13 pm

Thanks, though I can't take all the credit. I persuaded a work colleague to do most of it for me.
rust never sleeps
bss325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 24532
Joined: Sat Jan 20, 2007 11:00 pm
Location: London/Surrey

Post Tue Mar 10, 2009 6:03 pm

Looks like a decent repair but the zinc primer should have gone on before the seam sealer.
http://www.bmrperformance.co.uk

BMW and MINI specialist - Gatwick
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Mar 10, 2009 10:06 pm

I've heard and read opinions from both camps about whether to prime first and seal second or vice versa.

I chose to seal straight onto the bare welds because I read that polyurethane sealer sticks better to bare metal than paint does. It will also stick better to the metal than it will to primer. So long as the metal underneath is sound and properly cleaned...

Time will tell if I made the correct choice.
rust never sleeps
bss325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 24532
Joined: Sat Jan 20, 2007 11:00 pm
Location: London/Surrey

Post Tue Mar 10, 2009 10:32 pm

All shells are primed first then seam sealed/stone chipped when constructed at the factory. This is also the correct procedure in body repair. Bare metal should be etch primed first.
http://www.bmrperformance.co.uk

BMW and MINI specialist - Gatwick
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Tue Mar 10, 2009 10:54 pm

Every day is a school day :)

Thanks for the advice. I'll do it the other way round on the next welding job I tackle.

..So have I been badly misinformed about applying the seam sealer first or has anyone else heard that doing it the 'wrong way round' works better or worse?
rust never sleeps
Scruffymurphy
E30 Zone Regular
E30 Zone Regular
Posts: 775
Joined: Sun Sep 24, 2006 11:00 pm
Location: Ireland

Post Tue Mar 10, 2009 11:40 pm

Good work. The rust was well advanced, how is the rest of the car? It would be unusual for for the rust to be that bad n one area.
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Wed Mar 11, 2009 8:13 am

The rest of the car is pretty horrible to be honest but I've seen worse tackled by folk on here. It's not beyond saving but I've got more work to do, namely the jacking points. The underside of the car could do with a serious pressure wash and a good helping of underseal and waxoyl.

It spent the latter part of its life near the sea and I don't think it was very well looked after. Hopefully I can prolong the life of the shell by at least a couple of years.
rust never sleeps