Hottuning 6 branch

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Mon Feb 18, 2008 2:34 pm

Sorry about the delay in getting the 2nd dyno run done!

Finally got it done this morning, big thanks to Paul (sheps) for the dyno runs/time.

Manifold was fitted to my 325i touring, before fitting, only mods were a full sebring exhaust system, zone chip and an induction kit.

Obviously a good strong engine to start with, engine came from an auto with just over 100k on the clock.

Red line shows pre hottuning, purple with hottuning.

No adjustments were made to the fuelling, Paul pointed out that the car is running rich at some points since fitting the manifold, and obviously a remap would sort this out.

All in all, it's shown an improvement, good increase in torque, and it looks much nicer in the engine bay than the cast manifold.


Image
Image
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Mon Feb 18, 2008 2:52 pm

Not a bad result on the torque (except in the 3,000rpm region), but a gain of 0.6bhp at the wheels isn't much to shout about :? Doubt I'll be rushing to buy one tbh.
Last edited by Speedtouch on Mon Feb 18, 2008 3:00 pm, edited 1 time in total.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
march109
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6632
Joined: Sun Aug 20, 2006 11:00 pm
Location: Bournemouth

Post Mon Feb 18, 2008 2:59 pm

Be interested to see how it goes after a remap, BUT again it probably would'nt be fair comparison and remap before too.
325i Tech 1 Touring, breaking.

2.5 high comp. M20, 3.64 LSD, Fully undersealed, Spax springs & Bilstein shocks, s/s exhaust, Alpina rep wheels and more.
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Mon Feb 18, 2008 3:02 pm

Who's shouting?

Overall, the manifold has made an improvement, this is plain to see, as said, a good remap will sort the fuelling issues out, and make the most of the 6 branch.
Image
march109
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6632
Joined: Sun Aug 20, 2006 11:00 pm
Location: Bournemouth

Post Mon Feb 18, 2008 3:12 pm

Speedtouch wrote:Not a bad result on the torque (except in the 3,000rpm region), but a gain of 0.6bhp at the wheels isn't much to shout about :? Doubt I'll be rushing to buy one tbh.
Definatly not shouting about it, just replying to the 100's of posts asking if anyone had dynoed it yet. I for one was getting very sick of them. No everyone has a graph and a thread they can refer to before putting their money down on a 6 branch.
325i Tech 1 Touring, breaking.

2.5 high comp. M20, 3.64 LSD, Fully undersealed, Spax springs & Bilstein shocks, s/s exhaust, Alpina rep wheels and more.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Mon Feb 18, 2008 4:01 pm

Well well well,a result at last!!! Many thanks Simon. As has been said many times,each bhp costs....It will be interesting to see what mine will give next time. I still maintain that a capacity boost is the most effective way of improving an M20,my torque 'curve' almost peaks at 2000rpm with a gentle rise to 5000rpm...
Youth is wasted on the young.
oguz327
Captain Armco
Captain Armco
Posts: 4174
Joined: Tue Oct 25, 2005 11:00 pm
Location: Hampshire

Post Mon Feb 18, 2008 7:08 pm

Not a bad result there Simon, for 200 sheets you cant go wrong :cool:
ShepsEvo3
Master of go faster
Posts: 1881
Joined: Tue Mar 29, 2005 11:00 pm
Location: Bristol/Wiltshire

Post Mon Feb 18, 2008 7:10 pm

Speedtouch wrote:Not a bad result on the torque (except in the 3,000rpm region), but a gain of 0.6bhp at the wheels isn't much to shout about :? Doubt I'll be rushing to buy one tbh.
Yes, looks like the car was running much richer where the torque has dropped off to what it was before. Obviously the manifold flows better, but its silly just fitting this manifold expecting spectacular results... any changes like this will only benifit from a remapping session.

The 0.6 bhp increase at the wheels isn't much to shout about, but then thats not the figure you should be looking at when viewing figures from a Dastek dyno. I could run and run the car untill I am blue in the face and gain another 10bhp at the wheels, the flywheel figure will constantly be within 1bhp. And that goes for ambient temps also. So doing this exercise to get power at the wheel figure to stablize is a complete waste of my time and the customers money.

All in all, Simon has noticed a difference in the performance of the car, but to make the most of it the fueling and ignition timing will need attention throughout. I was expecting a loss, but that never happened except around 3000 RPM and from 6100 RPM onwards where in both places were much richer than the before runs.
E30 M3 Unichip Alpha N style conversions, this is the ultimate for extracting the best out of your S14 M power car.
Also, Live mapping of your Standard Motronic ECU for optimising all your modifications.
www.sabre-tuning.co.uk
ShepsEvo3
Master of go faster
Posts: 1881
Joined: Tue Mar 29, 2005 11:00 pm
Location: Bristol/Wiltshire

Post Mon Feb 18, 2008 7:18 pm

march109 wrote:Be interested to see how it goes after a remap, BUT again it probably would'nt be fair comparison and remap before too.
This is what I thought, but how far do you go? You would probably get more power out of this car out of a live remap with this manifold fitted than with one without.

I never used to thing changing something like this can affect the tune of the car atall, but I have seen time and time again that it does affect it dramatically in some cases.
E30 M3 Unichip Alpha N style conversions, this is the ultimate for extracting the best out of your S14 M power car.
Also, Live mapping of your Standard Motronic ECU for optimising all your modifications.
www.sabre-tuning.co.uk
oguz327
Captain Armco
Captain Armco
Posts: 4174
Joined: Tue Oct 25, 2005 11:00 pm
Location: Hampshire

Post Mon Feb 18, 2008 7:19 pm

How does the manifold sound Simon/Paul?
ShepsEvo3
Master of go faster
Posts: 1881
Joined: Tue Mar 29, 2005 11:00 pm
Location: Bristol/Wiltshire

Post Mon Feb 18, 2008 7:29 pm

oguz327 wrote:How does the manifold sound Simon/Paul?
I didn't notice any difference, but the exhaust note does sound nice. I wouldn't mind my car sounding like it.

I would imagine it to sound "tinnier" than before, which I think Simon says the same?
E30 M3 Unichip Alpha N style conversions, this is the ultimate for extracting the best out of your S14 M power car.
Also, Live mapping of your Standard Motronic ECU for optimising all your modifications.
www.sabre-tuning.co.uk
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Mon Feb 18, 2008 7:32 pm

could the over fueling be caused by the zone chip? worth trying a different chip out now you know what to expect?
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
ShepsEvo3
Master of go faster
Posts: 1881
Joined: Tue Mar 29, 2005 11:00 pm
Location: Bristol/Wiltshire

Post Mon Feb 18, 2008 7:38 pm

HairyScreech wrote:could the over fueling be caused by the zone chip? worth trying a different chip out now you know what to expect?
It was running rich and lean in a few areas before, but was running even richer in the rich areas and the same AFR's from approx 4000 to 6000 where after that went really rich again.

Simon has the AFR charts to show Ant and I am sure Ant will supply a modified chip to based on those charts.
E30 M3 Unichip Alpha N style conversions, this is the ultimate for extracting the best out of your S14 M power car.
Also, Live mapping of your Standard Motronic ECU for optimising all your modifications.
www.sabre-tuning.co.uk
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Mon Feb 18, 2008 8:37 pm

Cheers Paul.

With regards to the noise, I haven't noticed to much of a difference, the car sounds deep and burbly anyway with the sebring see the below link for a sound clip.

http://www.youtube.com/watch?v=kQJul7vad5A

There is a slight noise difference, difficult to describe really, kind of high pitched rushing noise. It doesn't help that I don't have no carpet in the car at the moment!
Image
Onz
E30 Zone Regular
E30 Zone Regular
Posts: 836
Joined: Sat Aug 26, 2006 11:00 pm

Post Mon Feb 18, 2008 11:22 pm

Well done mate! Thanks for the dynos :)

Great improvement in the torque curves, Does it pick up the revs faster while driving?
beardymat
E30 Zone Squatter
E30 Zone Squatter
Posts: 1979
Joined: Tue Jun 14, 2005 11:00 pm
Location: sheffield, city of steel, and rust apparently

Post Mon Feb 18, 2008 11:40 pm

did you just fit the manifold straight from the box?

when i had a look round the one that he30 bought i noticed one or two steps on the inside of the pipes where they join the various parts together, i suggested on the other thread that a little work with a dremmel or similar would help this issue and possibly aid gas flow.

for what its worth my btb equipped car with 87k made slightly under standard power when dyno`d although im not convinced the exhaust i bought in order to fit it is all that good and i didnt get it dyno`d before fitting. certainly didnt feel much different at the time of fitting.
No longer self employed but still available for welding duties.
oakey
E30 Zone Addict
E30 Zone Addict
Posts: 4891
Joined: Fri Feb 10, 2006 11:00 pm
Location: Surrey

Post Tue Feb 19, 2008 12:10 am

I'd say that's a good result! 8)
Image
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Tue Feb 19, 2008 8:24 am

There was one area that needed a little work, but that was it.
Image
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Tue Feb 19, 2008 5:54 pm

Good work Si,

At least someone willing to put their money where their mouth is!

Remember guys area under the graph! :cool:
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Tue Feb 19, 2008 8:27 pm

These 6 branches are down to E250 over here, that's about 150 quid!
Image

E30 zone - promoting adult illiteracy since 2004
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Feb 19, 2008 8:34 pm

datourer wrote: E250 over here, that's about 150 quid!
Not any more it isn't! Much closer to £200 than £150.
The days of £1 = E1.5 are over!
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Tue Feb 19, 2008 8:36 pm

but if theres very little power increase and no difference to the noise then what is the point in these? :?
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Tue Feb 19, 2008 8:41 pm

Shiny 6 branch or crusty old log manifold? If you're into detailing your bay it's a no brainer.
Image

E30 zone - promoting adult illiteracy since 2004
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Tue Feb 19, 2008 8:43 pm

The M20 is difficult to get power from.

Easiest way to get more power is a cc increase.

If this is not an option, then exhausts, chips is the way to go.

Standard 325i is 170bhp, this one is showing 183.7bhp, which I'm sure most will agree is good for a standard M20 with no internal modifications.

I'm sure with a decent remap, there would be more to be found too.
Image
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Tue Feb 19, 2008 8:48 pm

183? thats not bad . i suppose every little helps. i remember reading on here a couple of years ago that 200bhp was considered near impossible from an m20. is that still a widely held belief or has tuning progressed much since then?
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Tue Feb 19, 2008 9:32 pm

200bhp from a stock 2.5 M20, with standard AFM and motronic is not achievable, just buy using bolt on mods.

Things have progressed, but that means using different management systems, and junking the standard stuff.

Thing is, I want to test and compare other things now!
Image
ShepsEvo3
Master of go faster
Posts: 1881
Joined: Tue Mar 29, 2005 11:00 pm
Location: Bristol/Wiltshire

Post Tue Feb 19, 2008 10:15 pm

190 probably is though :wink:
E30 M3 Unichip Alpha N style conversions, this is the ultimate for extracting the best out of your S14 M power car.
Also, Live mapping of your Standard Motronic ECU for optimising all your modifications.
www.sabre-tuning.co.uk
User avatar
Paynts
E30 Zone Newbie
E30 Zone Newbie
Posts: 135
Joined: Sun Jan 13, 2008 11:00 pm

Post Tue Feb 19, 2008 10:55 pm

just had mine done by Aldon Automative great guys!! 169 at the wheels @7200rpm approx but I have got throttle bodies and a 6 branch exhaust

I think 230 ish might be possible with the right cam and valves etc

anyone got a top figure for naturally aspirated M20?
ShepsEvo3
Master of go faster
Posts: 1881
Joined: Tue Mar 29, 2005 11:00 pm
Location: Bristol/Wiltshire

Post Tue Feb 19, 2008 10:57 pm

I've seen 227.5bhp out of a 2.7.
E30 M3 Unichip Alpha N style conversions, this is the ultimate for extracting the best out of your S14 M power car.
Also, Live mapping of your Standard Motronic ECU for optimising all your modifications.
www.sabre-tuning.co.uk
march109
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6632
Joined: Sun Aug 20, 2006 11:00 pm
Location: Bournemouth

Post Tue Feb 19, 2008 11:00 pm

Isn't Players around 250bhp for a 2.8?

There are 3.0 and 3.1 L M20's too, with some serious work theres more power to be had, not cheap I expect. basic 2.8/2.9 far more reasonable £ wise.
325i Tech 1 Touring, breaking.

2.5 high comp. M20, 3.64 LSD, Fully undersealed, Spax springs & Bilstein shocks, s/s exhaust, Alpina rep wheels and more.
oakey
E30 Zone Addict
E30 Zone Addict
Posts: 4891
Joined: Fri Feb 10, 2006 11:00 pm
Location: Surrey

Post Tue Feb 19, 2008 11:05 pm

Mine will be done in the next couple of weeks winkeye
Image
march109
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6632
Joined: Sun Aug 20, 2006 11:00 pm
Location: Bournemouth

Post Tue Feb 19, 2008 11:11 pm

Oakey what displacement are you going for?
325i Tech 1 Touring, breaking.

2.5 high comp. M20, 3.64 LSD, Fully undersealed, Spax springs & Bilstein shocks, s/s exhaust, Alpina rep wheels and more.
User avatar
Paynts
E30 Zone Newbie
E30 Zone Newbie
Posts: 135
Joined: Sun Jan 13, 2008 11:00 pm

Post Tue Feb 19, 2008 11:17 pm

Hmm is a 2.7 cheap to build ? will the manifold off my 2.5 fit? or can I use my 2.5 head? any ideas? can you get second hand 2.7 motors easily?
I want to stay with the M20 and I would be happy with 220
oakey
E30 Zone Addict
E30 Zone Addict
Posts: 4891
Joined: Fri Feb 10, 2006 11:00 pm
Location: Surrey

Post Tue Feb 19, 2008 11:19 pm

Mines a 2.7 already, standard cam, 6 branch and megasquirt. But I'm having Ant fit itbs and I'll probably ask him to fit one of his cams :D I had it recently dynoed at 205hp and 225 ftlb and it was mapped on the road so I'm hoping for a fair old increase with those goodies fitted and a dyno remap. :D
Image
march109
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6632
Joined: Sun Aug 20, 2006 11:00 pm
Location: Bournemouth

Post Tue Feb 19, 2008 11:20 pm

Paynts wrote:Hmm is a 2.7 cheap to build ? will the manifold off my 2.5 fit? or can I use my 2.5 head? any ideas? can you get second hand 2.7 motors easily?
I want to stay with the M20 and I would be happy with 220
Read this link: http://www.e30zone.net/modules.php?name ... ic&t=89665

All you need and more to make an informed choice and collect all the parts!
325i Tech 1 Touring, breaking.

2.5 high comp. M20, 3.64 LSD, Fully undersealed, Spax springs & Bilstein shocks, s/s exhaust, Alpina rep wheels and more.