fu#*ing check control panel

Need technical Q/A then you're in the right place

Moderator: martauto

Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Mon Feb 19, 2007 3:06 pm

I was tidying my engine bay a few weeks ago and rotated the sensor in the screen washer bottle to tidy the wires up. When I finished I put the sensor back to it's original position, and of course since then the light on my check panel stays on. All wires/connections are good and of course there is plenty of water in the bottle. Any tips anyone??
Image

E30 zone - promoting adult illiteracy since 2004
maxfield
Old Skooler
Old Skooler
Posts: 15185
Joined: Sat Nov 26, 2005 11:00 pm
Location: Mansfield

Post Mon Feb 19, 2007 3:09 pm

My dads car always has this light on.

Just keep fettling around with till it's gone normally works.
Image
User avatar
toby
E30 Zone Addict
E30 Zone Addict
Posts: 3609
Joined: Thu Aug 11, 2005 11:00 pm
Location: Kent

Post Mon Feb 19, 2007 3:11 pm

The float in the bottle sometimes, somehow, turns upside down. So when the washer bottle is full it lifts the float off the contact and apears empty. It may have turned itself round again.

Check the float is not upside down.
Image
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Mon Feb 19, 2007 3:12 pm

The float should be pointing towards the top of the bottle, right?
Image

E30 zone - promoting adult illiteracy since 2004
User avatar
toby
E30 Zone Addict
E30 Zone Addict
Posts: 3609
Joined: Thu Aug 11, 2005 11:00 pm
Location: Kent

Post Mon Feb 19, 2007 6:19 pm

No I don't think so.

See diagram no.4

Float should be facing the base of the bottle.

When the water level rises the float then closes the contact - no check control light.

If upside down the float is lifted off the contact.

Basically the float should drop down when the bottle is empty.

Image
Image
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Tue Feb 20, 2007 7:10 pm

I've turned the damn thing all around and the light still stays on, any more tips?
Image

E30 zone - promoting adult illiteracy since 2004
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue Feb 20, 2007 7:56 pm

Remove check control panel, pull multi plug out, replace :cool:
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Feb 20, 2007 8:02 pm

Can't remember which way around the washer level switch works, but try pulling the plug off the sensor and see if the light stays off when you switch the ignition on. Next fit a shorting link between the pins of the sensor's socket and try again. One way around, the light should stay off.
Thinking about it, it should stay off with the link in place, as I'm sure the light comes on when I move half dismantled cars around.
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Tue Feb 20, 2007 8:05 pm

Cheers, I may try both suggestions tomorrow...
Image

E30 zone - promoting adult illiteracy since 2004