spray carb cleaner down the hole?
Rear ABS teeth?
Moderator: martauto
-
sam325is
- E30 Zone Addict

- Posts: 2002
- Joined: Thu Jul 06, 2006 11:00 pm
- Location: Cheltenham
itook my abs sendsor out from the rear wheel today and if i look down thew hole i can see teeth, they are quite dirty. how should i go about cleaning them?
spray carb cleaner down the hole?
spray carb cleaner down the hole?
-
spence_star
- E30 Zone Regular

- Posts: 512
- Joined: Thu Nov 23, 2006 11:00 pm
- Location: London
does it make a noise when you drive like a touching noise?
Returned after many years out.
-
sam325is
- E30 Zone Addict

- Posts: 2002
- Joined: Thu Jul 06, 2006 11:00 pm
- Location: Cheltenham
what do you mean? i cant really recall it making any noise no. what is there for it to touch
-
spence_star
- E30 Zone Regular

- Posts: 512
- Joined: Thu Nov 23, 2006 11:00 pm
- Location: London
ok no reason, my ABS light came on for one day and stayed on the whole day bt now its gone off, and has never come back on since. i have a feeling a sensor is on its way out
Returned after many years out.
-
sam325is
- E30 Zone Addict

- Posts: 2002
- Joined: Thu Jul 06, 2006 11:00 pm
- Location: Cheltenham
ahh right. i have a problem where all my sensors are fine but the teeth they read from are too dirty.
anyone know how to clean them?
anyone know how to clean them?
-
sam325is
- E30 Zone Addict

- Posts: 2002
- Joined: Thu Jul 06, 2006 11:00 pm
- Location: Cheltenham
anyone?
-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
Brake cleaner.
Andrew
Andrew
-
sam325is
- E30 Zone Addict

- Posts: 2002
- Joined: Thu Jul 06, 2006 11:00 pm
- Location: Cheltenham
where does all the brake cleaner go that drips off? as it is in a casing
-
hairydave
- E30 Zone Newbie

- Posts: 106
- Joined: Wed May 10, 2006 11:00 pm
- Location: Fleetwood, Lancs
It will evaporate
-
sam325is
- E30 Zone Addict

- Posts: 2002
- Joined: Thu Jul 06, 2006 11:00 pm
- Location: Cheltenham
where will it evaporate to though? because once the abs sensor is plugged back into the hole its a sealed unit isnt it?
Thanks
Thanks
-
hairydave
- E30 Zone Newbie

- Posts: 106
- Joined: Wed May 10, 2006 11:00 pm
- Location: Fleetwood, Lancs
Wait a while before you plug it back in then. 
-
TINSNIPS
- E30 Zone Newbie

- Posts: 93
- Joined: Sun Feb 20, 2005 11:00 pm
- Location: MILTON KEYNES
it will not mater that the ring is dirty unless they are badly rust ,the ring works by interupting the magnetic feild produced by the speed sensor(abs sensor) when the wheel stops spinning there is no pulse at that wheel and the brake effort at that wheel is reduced ,the wheel then rotates hence the brake pedal pulse, unless there is a problem with the abs leave well alone
-
ian332isport
- E30 Zone Team Member

- Posts: 5380
- Joined: Wed Dec 22, 2004 11:00 pm
- Location: West Sussex
It's not sealed. The ABS ring is actually on the CV joint/driveshaft. All the brake cleaner will simply drip out of the bottom and evaporate.sam325is wrote:where will it evaporate to though? because once the abs sensor is plugged back into the hole its a sealed unit isnt it?
Thanks
Mind you, brake cleaner is only really going to shift greasy/oily dirt. If it's just old and crusty, you really need to get in there with a small screwdriver and make sure the teeth are not too clogged.
Ian.
If it aint broke - Modify it...
-
old_skool
- E30 Zone Team Member

- Posts: 3405
- Joined: Fri Sep 01, 2006 11:00 pm
- Location: Glossersure
Sam,
When you overhaul the rear beam, like you are planning on - *cough* you will need to drop the driveshafts out. Then you will be able to clean the ABS rings with a wire brush all you like
When you overhaul the rear beam, like you are planning on - *cough* you will need to drop the driveshafts out. Then you will be able to clean the ABS rings with a wire brush all you like
-
old_skool
- E30 Zone Team Member

- Posts: 3405
- Joined: Fri Sep 01, 2006 11:00 pm
- Location: Glossersure
Here you go. Look at the top of the pic to see the ring location:



