uprating wiring for 100W bulbs
Moderator: martauto
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
'if' i were to fit 100w bulbs for 'off road use', will the wiring on the E30 handle it? obviously upgrading the relays and fuses will be easy enough, ensuring all connectors are good is obviously required but will the wire gauge be sufficient or is there a likelihood of overheating?
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
I just upped the fuses to 15 amp!

-
gazza
- E30 Zone Camper

- Posts: 1266
- Joined: Tue Feb 08, 2005 11:00 pm
- Location: north london/herts
for extended use i would ...but if you are just swopping your main beam then you may get away with it as you dont drive all the time with them on ....just for the odd dark lane etc ...fit them and try them out leave them on for a few minutes and see if the wiring to them gets hot if it does fit a relay and better wiring also make sure your lights are correctly adjusted so you dont blind anyone cos then you will bring notice to yourself and on closer inspection someone will spot illegal bulbs .....i fitted 80watt main beam and find them more than adequate(off rd use only off course) and if you buy them from halfords then they are cheaper than normal bulbs
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
See "Bosch HID kit" thread, which I've just moved here from ebay.
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
thanks lads! 
i've just read though that thread... took a while! i'm not a fan of the HID's to be honest as they look odd when you go to full beam as the original lights then look brown!
i might have a go at fitting them and leave them on while stationary to see how the wiring does. if it gets warm, i'll fit some relays near the light and power them from a seperate loom.
older VW's have a problem with the lighting circuit that is cured in a very similar way... the massive length of the lighting loom and the dodgy switches drop the voltage a lot by the time you reach the lights. i fitted an uprated bypass loom (ebay) to our corrado as the light were shocking! the voltage drop from the loom / switchgear equated to the n/s bulbs seeing 8.7 volts and the o/s bulbs seeing 8.4 volts!!!!
a few feet of wire and a few relays later and i had just a 0.1 volt drop from the battery to the bulbs which made a massive difference!
i've just read though that thread... took a while! i'm not a fan of the HID's to be honest as they look odd when you go to full beam as the original lights then look brown!
i might have a go at fitting them and leave them on while stationary to see how the wiring does. if it gets warm, i'll fit some relays near the light and power them from a seperate loom.
older VW's have a problem with the lighting circuit that is cured in a very similar way... the massive length of the lighting loom and the dodgy switches drop the voltage a lot by the time you reach the lights. i fitted an uprated bypass loom (ebay) to our corrado as the light were shocking! the voltage drop from the loom / switchgear equated to the n/s bulbs seeing 8.7 volts and the o/s bulbs seeing 8.4 volts!!!!
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
