Tips on installing H&R roll bars
Moderator: martauto
-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
As above..
Any tips on installing these? I had a bsash at it earlier today, but ran out of time.. so now driving with no front sway bar.
(And for those wondering how to set up your roll bars.. I can honestly say DO NOT make the ass harder than the front.. You'll be oversteering left right cantre.)
The rear is on the hole furthest from the ends, ther fronts I'm putting on the stiffest, (the last hole or closest to the end)
Are the bushes sposed to be bigger than the bracket? They stick out heaps over the top of the bracket where it mounts.
tips??
Any tips on installing these? I had a bsash at it earlier today, but ran out of time.. so now driving with no front sway bar.
(And for those wondering how to set up your roll bars.. I can honestly say DO NOT make the ass harder than the front.. You'll be oversteering left right cantre.)
The rear is on the hole furthest from the ends, ther fronts I'm putting on the stiffest, (the last hole or closest to the end)
Are the bushes sposed to be bigger than the bracket? They stick out heaps over the top of the bracket where it mounts.
tips??
-
SPADGE
- Married to the E30 Zone

- Posts: 7373
- Joined: Wed Aug 09, 2006 11:00 pm
- Location: Milton Keynes, Bucks
STEP AWAY FROM THE TOOLBOX!oze30 wrote:tips??
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
-
DRIFTBOY
- E30 Zone Addict

- Posts: 3131
- Joined: Mon May 22, 2006 11:00 pm
- Location: Kent
oze30 wrote:
(And for those wondering how to set up your roll bars.. I can honestly say DO NOT make the ass harder than the front.. You'll be oversteering left right cantre.)
Yeah, they do seem at first like they might not fit.
I made it a bit easier for myself by using longer bolts (8mm thread - 13mm head) through the brackets at first, clamping the bracket with mole grips, then removing the long bolt and fitting one nearer the correct length. Once both sides are fitted the roll bar should move in the bushes with very little effort, but not flopping around!
Perfect time to fit new drop links also, replacements of inferior quality are known to wear their bushes out quickly!
Jeremy Clarkson wrote:...but it drives the front wheels. Theee wrooong wheels!
da4x4turbo wrote:I raced a vivaro on the motorway once in a 318is.... and lost!!!
-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
thats confidence!!!SPADGE wrote:STEP AWAY FROM THE TOOLBOX!oze30 wrote:tips??
![]()
-
Jamesb318is
- E30 Zone Regular

- Posts: 620
- Joined: Wed Jan 12, 2005 11:00 pm
- Location: East Sussex
The holes closest to the end of the bars are the softest settings, sounds like you're describing it the other way round above.
You can also use a trolley jack or similar to push the bushes and brackets up into place.
One tip I have is not to dig a stanley knife into your wrist while trimming down the bushes slightly, i did this and ended up in casualty lol!
You can also use a trolley jack or similar to push the bushes and brackets up into place.
One tip I have is not to dig a stanley knife into your wrist while trimming down the bushes slightly, i did this and ended up in casualty lol!


-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
Can anyone clarify this? I didnt get instructions with it.Jamesb318is wrote:The holes closest to the end of the bars are the softest settings, sounds like you're describing it the other way round above.
You can also use a trolley jack or similar to push the bushes and brackets up into place.
One tip I have is not to dig a stanley knife into your wrist while trimming down the bushes slightly, i did this and ended up in casualty lol!
-
HenryM3
- E30 Zone Regular

- Posts: 676
- Joined: Mon Feb 05, 2007 11:00 pm
- Location: Bournemouth
Top tip James about the stanley knife. oze30 I'd have to agree with James about the roll bar settings. Nearest the end = soft. Furtherest from end = hardest/stiffest
Cheers
Henry
Cheers
Henry
-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
so to clarify....HenryM3 wrote:Top tip James about the stanley knife. oze30 I'd have to agree with James about the roll bar settings. Nearest the end = soft. Furtherest from end = hardest/stiffest
Cheers
Henry
If the roll bar is U shaped.. the holes towards the top of the U are the softest.
The holes near the flat of the U are hardest?
-
HenryM3
- E30 Zone Regular

- Posts: 676
- Joined: Mon Feb 05, 2007 11:00 pm
- Location: Bournemouth
Don't like the way your explaining that, theres room for confusion. The holes nearest the very ends of the roll bar are the softest settings.
Cheers
Henry
Cheers
Henry
-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
Cool.. Cheers
Just have to install them now!!
Another Q Henry,
If I want to set the car up for oversteer, is it hard front soft rear?
Just have to install them now!!
Another Q Henry,
If I want to set the car up for oversteer, is it hard front soft rear?
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
best setting for road use is on rear hardest the end hole on the rear and middle on the front, you can on track use the stiffest all round, but mind they don't rip off the mounting points!
no matter how big the mounting bushes are they will go in and don't give up! I use a thin bar with a trolley jack to push the bracket and bush up in place so i can get the nut and bolt back in. The bar is at angle though so it pushes the bracket in and up if you get me! The rear is similar but not as much swearing
No one has ver posted up an official way of doing it!
no matter how big the mounting bushes are they will go in and don't give up! I use a thin bar with a trolley jack to push the bracket and bush up in place so i can get the nut and bolt back in. The bar is at angle though so it pushes the bracket in and up if you get me! The rear is similar but not as much swearing
No one has ver posted up an official way of doing it!
-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
I used mole grips on the rear. That was fun.. had one side up on a gutter and jack on the other
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
Colin just get the spadge meister round! easy!
-
SPADGE
- Married to the E30 Zone

- Posts: 7373
- Joined: Wed Aug 09, 2006 11:00 pm
- Location: Milton Keynes, Bucks
I did offer for him to bring the hearse here so i could lend a hand but Col would rather struggle himself for some reasonSimon13 wrote:Colin just get the spadge meister round! easy!
More time for me to play with my own toys so fine by me
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
Might still do it.. pending when my flatmate wants to get her car
-
HenryM3
- E30 Zone Regular

- Posts: 676
- Joined: Mon Feb 05, 2007 11:00 pm
- Location: Bournemouth
I assume simon has done his anti roll bars, and is giving his recommendations on experience with those anti roll bars. To answer your question to me. Stiff rear, Soft front = oversteer. But be carefull, yes you'll be able to hang the arse out at low and medium speeds, but the arse will have already dissapeared into the hedge at high speed. Some one in a standard car at high speed will go round the corner 10mph quicker because he has a balanced car. If you have spent all that money on H & R roll bars with adjustment holes so that you can get the balance just right it seems a shame to waste it.
Cheers
Henry
Cheers
Henry
-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
cool.. Cheers
