Replacing hard brake lines /fuel lines / clutch lines

Need technical Q/A then you're in the right place

Moderator: martauto

Gwynleym10
E30 Zone Addict
E30 Zone Addict
Posts: 3650
Joined: Sun Jan 09, 2005 11:00 pm
Location: London/Cymru

Post Tue Feb 13, 2007 9:47 pm

I probably going to replace my hard lines (oh er!) in the next few months. Can someone tell me the following:

The size of the fittings for the brake lines.
Size of the pipe, and what material is best.

The size of the hard clutch line fixings (is it the same as the brake?)


Fuel lines, is this dealer only parts? any other options?

Thanks!

PS I can seem to work the search function only does one page, then computers says no!?
Image
Dual wheel carriers -------195litre Fuel Tank
London 2 Cape Town
www.Overlandinthesun.com
sam325is
E30 Zone Addict
E30 Zone Addict
Posts: 2002
Joined: Thu Jul 06, 2006 11:00 pm
Location: Cheltenham

Post Tue Feb 13, 2007 9:51 pm

i have had some fuel lines from a dealer and they come pre-bent and fit very easy. however when you try to unscrew they metal clips that hold the fuel lines up they tend to snap so this makes the job annoying. you will have to drill out the screw and re-tap the holes
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Feb 13, 2007 10:09 pm

Best material for brake and clutch lines is "cunnifer" copper nickel alloy pipe. It's sold as 3/16" which is the correct size. Make sure you get metric ends to use with it. Imperial ones are very similar untill you try to screw them in. (Don't ask how I know!).
You can also use 1/4" cunnifer for fuel lines. Use a flaring tool to put a small bell on the ends.
No more than about £10's worth of materials on an E30, although a coil of each size will cost about £20 the pair.
Gwynleym10
E30 Zone Addict
E30 Zone Addict
Posts: 3650
Joined: Sun Jan 09, 2005 11:00 pm
Location: London/Cymru

Post Tue Feb 13, 2007 10:20 pm

Thanks Brian

So the ends are 3/16 metric for the brake line?

This flaring tool will do the job wont it?

http://cgi.ebay.co.uk/PIPE-FLARING-SET- ... 0082551121
Image
Dual wheel carriers -------195litre Fuel Tank
London 2 Cape Town
www.Overlandinthesun.com
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Feb 13, 2007 10:29 pm

Tool is different than mine, but it looks like it should do the job.
You can get the pipe and ends from any motor factors. Just stress you need metric male ends, not imperial.
Ends are about 10p each.
I would advise getting all new flexible lines as well (GSF, Eurocarparts) and new spring clips for the ends of the flexibles from your dealer.
Gwynleym10
E30 Zone Addict
E30 Zone Addict
Posts: 3650
Joined: Sun Jan 09, 2005 11:00 pm
Location: London/Cymru

Post Wed Feb 14, 2007 7:01 am

Thanks Brian, I have new flexible hoses coming. Forgot about the spring clips Thanks!
Image
Dual wheel carriers -------195litre Fuel Tank
London 2 Cape Town
www.Overlandinthesun.com
Gwynleym10
E30 Zone Addict
E30 Zone Addict
Posts: 3650
Joined: Sun Jan 09, 2005 11:00 pm
Location: London/Cymru

Post Wed Feb 14, 2007 6:17 pm

1 more question, do I need a pipe bending tool, or is it ok to bend them by hand?

Thanks
Image
Dual wheel carriers -------195litre Fuel Tank
London 2 Cape Town
www.Overlandinthesun.com
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Feb 14, 2007 7:13 pm

Cunnifer pipe is bendable by hand as long as you don't try to make too tight a bend.
The ones at the tee piece at the rear are the tightest, so start with these before you cut the pipe to length.
Gwynleym10
E30 Zone Addict
E30 Zone Addict
Posts: 3650
Joined: Sun Jan 09, 2005 11:00 pm
Location: London/Cymru

Post Wed Feb 14, 2007 7:18 pm

Excellent Brain

Thanks for your help
Image
Dual wheel carriers -------195litre Fuel Tank
London 2 Cape Town
www.Overlandinthesun.com