Steering issue 318is.

Need technical Q/A then you're in the right place

Moderator: martauto

GBE30
E30 Zone Regular
E30 Zone Regular
Posts: 341
Joined: Mon Aug 01, 2005 11:00 pm
Location: Brighton

Post Mon Feb 12, 2007 8:03 am

Hi All,

After some knowledge/advice.

I have an intermittent wheel wobble problem.........

It was first noticable at 80+ But now that I know its there I can see/feel it at 40 onwards. It comes and goes daily.

At speed it feels like i am having to correct the steering.

I have so far,

1.) Had all bushes, ball joints etc checked by my mechanic and my good self.
2.) Change wheels from back to front (Still there).
3.) Balanced all wheels.
4.) Had tracking adjusted.
5.) Rear end all ok.
6.) Visually checked top mounts all seem ok.

Now, My mechanic says that there is slight play in the rack but nothing that would do this. His one was worse and he was having zero issues!

So what is it likely to be, i have narrowed things done to what I think may be the culprit.

a.) Rack
b.) Front suspension
c.) Steering bush at UJ (Does a 1990 318is have this part?)
d.) Worn wrist on the driver in drivers seat :)

As I said this problem comes and goes.

Any pointers tips or relevant advise is very welcome as although it comes and goes, it may potentially be unsafe.

Many thanks

Gareth
monkey
E30 Zone Camper
E30 Zone Camper
Posts: 1222
Joined: Sat Jan 15, 2005 11:00 pm
Location: devon

Post Mon Feb 12, 2007 12:32 pm

you may have a front brake sticking on , just taking out the brake pads cleaning them and copper sliping may solve your problem or it could be a brake caliper .
Cava
E30 Zone Regular
E30 Zone Regular
Posts: 349
Joined: Sat Nov 19, 2005 11:00 pm
Location: South Wales

Post Mon Feb 12, 2007 1:31 pm

From previous experience, could be the caliper as suggested previously but also worth checking the alloys to see if any has a slight buckle and the front wheel bearings for wear.
GBE30
E30 Zone Regular
E30 Zone Regular
Posts: 341
Joined: Mon Aug 01, 2005 11:00 pm
Location: Brighton

Post Mon Feb 12, 2007 6:17 pm

My wheels are fine as they have been recently (Tues) balanced.

I cannot feel the vibration or shaking through nrake peddles and the car stops fine.

How can I prove a sticking caliper?
BadDave
E30 Zone Team Member
E30 Zone Team Member
Posts: 6012
Joined: Sun Jan 09, 2005 11:00 pm
Location: Nr Aberdeen.Scotland(Gods country)

Post Mon Feb 12, 2007 10:31 pm

Sticking caliper has a tendency to pull to the side
Alpina B10 3.2L #187 (1 of 64 brought into the UK)
2.8L turbo build thread(work in progress)
http://www.e30zone.net/modules.php?name ... 27#1268227
GBE30
E30 Zone Regular
E30 Zone Regular
Posts: 341
Joined: Mon Aug 01, 2005 11:00 pm
Location: Brighton

Post Tue Feb 13, 2007 6:50 am

My brakes feel absolutely fine. No pulling to either side even with heavy braking.

This is so frustrating.

I think I am going to look at the column bushe first as this is cheap.

Seems a very strange problem. That comes and goes, but always regular (within the same drive home from work etc).

Beginning to get a touch fed up with it.
monkey
E30 Zone Camper
E30 Zone Camper
Posts: 1222
Joined: Sat Jan 15, 2005 11:00 pm
Location: devon

Post Wed Feb 14, 2007 10:31 am

you could prove if there is anything wrong with brakes by taking the car to an m/o/t test staition and getting them to do a brake test if the brake is sticking it will show on the readings , take the car for a run first so the brakes are hot . you may not feel the brakes pulling to one side but it can cause wheel shake . the steering bush or worn uj will give you play in the steering and should be easy to see but should not give you wheel shake
Martinaston
E30 Zone Addict
E30 Zone Addict
Posts: 3749
Joined: Mon Mar 14, 2005 11:00 pm
Location: London

Post Wed Feb 14, 2007 10:49 am

When it gets a shake on try letting the car roll to a stop in neutral from about 15mph on level ground and see if you can feel the car stop quicker than it should, you may be able to feel the suspension recoil just as it comes to a stop.
It will only pull to the side if its realy badly binding, but if its that bad you can normaly feel that one wheel is hotter than the other.
If its binding its probably the outer seal in the caliper is perforated, it lets in water that then rusts the plating off the piston.
There is NO nucleus.