stupid question? headlight wipers

Need technical Q/A then you're in the right place

Moderator: martauto

ag-1982
E30 Zone Newbie
E30 Zone Newbie
Posts: 114
Joined: Thu Jan 04, 2007 11:00 pm
Location: SE Kent

Post Mon Feb 12, 2007 3:22 pm

how do i get my headlight wipers to work? :?
Morat
E30 Zone Team Member
E30 Zone Team Member
Posts: 8943
Joined: Thu Feb 09, 2006 11:00 pm
Location: The Peoples Republic of Yorkshire

Post Mon Feb 12, 2007 3:52 pm

There was a full tutorial somewhere on the net with pictures and instructions.
I'm buggered if I can find it now. I'm sure someone will have it bookmarked...
E30 Touring 0.35 cD - more slippery than prison soap :)

Image
Praise the Lard... and pass the dripping!
snoops
Major Helmet
Posts: 2828
Joined: Fri Nov 03, 2006 11:00 pm
Location: Time running out for me on the Zone

Post Mon Feb 12, 2007 4:38 pm

lol i need to know this as well
bazza93
E30 Zone Camper
E30 Zone Camper
Posts: 1305
Joined: Sat Sep 09, 2006 11:00 pm
Location: in corringham essex

Post Mon Feb 12, 2007 5:00 pm

mine work by turning headlights on then activating washwipe. then again my ones work :D many don't, they tend to sieze up :cry:
will be back in an E30 oneday soon !


THE BMW 3-SERIES. IT'S WHY SOME ENTHUSIASTS ARE MORE ENTHUSIASTIC,
sam325is
E30 Zone Addict
E30 Zone Addict
Posts: 2002
Joined: Thu Jul 06, 2006 11:00 pm
Location: Cheltenham

Post Mon Feb 12, 2007 5:50 pm

basically the back of the casing comes of by getting a small screw driver and opening all the clips that are around it,you have to put the screw driver down a gap and prize them open,its not to easy, dont worry if you break them as i suggest you use some strong silicone to seal the back casing up after wards. once this is removed you need to spray the spindle that the wipers join on to with WD40 so that all the wd runs down the spindle and in to the tube that the spindle goes through. let it soak for a while and repeat a few times.

Now you need to get a block of wood and place it on top of the spindle ( the end with the thread on). secure the whole unit so when you hit it the spidle will be able to come out of the back. now get a big hammer and keep hitting the block of wood untill it comes loose, if this doesnt work you might want to get a blow torch and heat the shaft then try again.

once you have the spindle out of the shaft you will see it has a cogon the end which turns a arm that has teeth on it, remove this arm and anything else which is on top. by this point you should be looking at a metal plate.

you now need to CAREFULLY prize this of using a screw driver.prize up one side gardually then another doing it bit by bit.

once this is off you will be able to see all the running gear (white plastic cogs) these can all be removed by hand. rember where they all go(maybe draw a diagram) and then clean up all the parts.

then get a drill bit that is quite long and fits snugg down the shaft that the spindle goes through and drill it out so that all the rust comes out.

then you need to clean the inside of the casing up regrease all the cogs be generous with the grease and refit everything.

then get the casing back on and seal up every single gap that water could possibly get through on the motor with silicone.

its quite a messy job but its worth it.

when you get to the inside of the casing(under the metal plate) have a little look around and you will notice a piece of metal sometimes its the shape of a 1 pence piece sometimes its just a rectangular piece of metal, this has two brass/copper connectors either side(they are not attached) of it make sure this in there when you replace everything as it is prone to falling out.

there is a giude with pictures somewhere on the internet. but as i learned THE ADVICE IS CRAP THERE IS NPO WAY that they refitted and used this system afterwards as there threads where the wipers are held on would have been fookered for a start. it is more of a wiper unit autopsy

Note: if the spindle doesnt come out even after heating with a blow torch its likely to be completly seized.

i have worked on a good few motors before and one i heated up untill it was almost redhot used half a can of WD and held it in a vice and repetativly hit the spindle with a sledge hammer and it still didnt come out. some are just fucked.

once you come to refit them if you dont have the rubber seal that covers the bit where the spindle goes down the shaft you can use some shrink wrap. doing this works just as well.

hope this helps

just ask if you have any questions :thumb:
jcjdavis1
E30 Zone Camper
E30 Zone Camper
Posts: 1128
Joined: Thu Apr 13, 2006 11:00 pm
Location: Paisley Scotland

Post Mon Feb 12, 2007 6:40 pm

Hi I tried the above but found the easy way was to look in the for sale section.
Image
ag-1982
E30 Zone Newbie
E30 Zone Newbie
Posts: 114
Joined: Thu Jan 04, 2007 11:00 pm
Location: SE Kent

Post Mon Feb 12, 2007 7:31 pm

nice one peeps ill let you know how i get on.

cheers :D
sam325is
E30 Zone Addict
E30 Zone Addict
Posts: 2002
Joined: Thu Jul 06, 2006 11:00 pm
Location: Cheltenham

Post Mon Feb 12, 2007 11:23 pm

jcjdavis1 wrote:Hi I tried the above but found the easy way was to look in the for sale section.


yea that is an easier option mate lol. but i expect that any original motors that are still working now wont have many more years in them.
ag-1982
E30 Zone Newbie
E30 Zone Newbie
Posts: 114
Joined: Thu Jan 04, 2007 11:00 pm
Location: SE Kent

Post Tue Feb 13, 2007 8:51 am

ive seen them go for loads on ebay so im not about to try buying a new set, reckon the scrappy will notice them in my pockets winkeye
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Feb 13, 2007 8:58 am

90% come apart reasonably easily. The only one I've ever had to bin had a massive hole rusted through the motor casing.
ag-1982
E30 Zone Newbie
E30 Zone Newbie
Posts: 114
Joined: Thu Jan 04, 2007 11:00 pm
Location: SE Kent

Post Wed Feb 14, 2007 7:57 pm

I took one of the motors apart and cleaned everything up, the motor inside works ok but as soon as you put a cog onto it it wont work could it be a naff motor?
sam325is
E30 Zone Addict
E30 Zone Addict
Posts: 2002
Joined: Thu Jul 06, 2006 11:00 pm
Location: Cheltenham

Post Wed Feb 14, 2007 8:08 pm

which cog? and how are you trying to operate it? you need to connect it to the car and turn the headlights on and then press the intesive wash stalk(push in) if you have both motors connected..which you should do,they should work every 5th time use press in the intensive wash stalk
danger_mouse
E30 Zone Newbie
E30 Zone Newbie
Posts: 18
Joined: Tue Feb 13, 2007 11:00 pm
Location: Cambridgeshire/Lancashire UK

Post Wed Feb 14, 2007 8:18 pm

ag-1982 wrote:I took one of the motors apart and cleaned everything up, the motor inside works ok but as soon as you put a cog onto it it wont work could it be a naff motor?
I'm so glad I signed up!

I'm not the only one baffled by about how to make the "Barvarian Steed" flutter her eyelashes ... phew.

Is it possible to re brush the motors? My guess is the motors will have enough torque spin by themselves but they will stall with any resistance... rambling now, the wine's kicking in, time to watch the brit's I think.

N'night
DM
Northern Biligerance Cannot be Learned, but it Can Sure as Hell be Appreciated
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Feb 14, 2007 8:23 pm

ag-1982 wrote:I took one of the motors apart and cleaned everything up, the motor inside works ok but as soon as you put a cog onto it it wont work could it be a naff motor?
I'm assuming you're powering the motor from an independent power supply of some sort.
Brown wire is negative, red wire is 12V positive. If the motor won't run when you put it together, then it's either still seized, have a duff motor or have a problem with the series blocking diode or the thermistor which provides overload protection for the motor.
If you get them running, then power them up with the independent supply after they're fitted to the car, to check the blades are on properly.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Feb 14, 2007 8:27 pm

danger_mouse wrote:Is it possible to re brush the motors?
DM
Highly unlikely the brushes have worn out. The motors will only have run for a few minutes total in their entire life.
The brushes in the fuel pump, for example, last for 8000 - 9000 hours.