as some of you will have noticed i am having ABS problems...
i have just bought a full abs pump / loom / ecu stup from theo325 but i 'think' it's from an earlier car (i'll ask him...). the giveaway being that the ecu's have different part numbers and there is an extra relay on the loom near the ecu (which my 1990 tourer does not have). the pump looks the same though it has flathead screws (rather than torqs) and a slightly different cover which doesn't say 'ABS'.
the bosch part numbers are as follows:
1990 touring ecu = 0 265 103 041
older(?) replacement ecu = 0 265 103 004
1990 touring pump = 0 265 200 040
older(?) replacement pump = 0 265 200 013
will i kill things if i simply plug the replacement pump and ecu in (they well connect up ok)
also, what actually triggers the ABS light on the dash and what should it do when healthy? (mine never has been!)
ABS part compatability
Moderator: martauto
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
The light is controlled by the ABS ECU.
When you switch on the igntion, the light will light up for a few seconds, then go out if everything is ok.
When you switch on the igntion, the light will light up for a few seconds, then go out if everything is ok.
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
cheers mate! the " going out" bit is what mine lacks! oh, and the ABS doing nothing!!!!
the abs always used to work but i never had a bulb fitted. obviously a previous owner covering a fault for mot / resale
the abs always used to work but i never had a bulb fitted. obviously a previous owner covering a fault for mot / resale
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
That sounds like the system I have. All seperate from main loom and with a relay.
Im having problems with it aswell, when it kicks in its like having the bottom of my foot hit with a hammer several times in a row. Im going to swap the pump soon as thats all it can be.
Are the elec plugs the same for the pumps?
Im having problems with it aswell, when it kicks in its like having the bottom of my foot hit with a hammer several times in a row. Im going to swap the pump soon as thats all it can be.
Are the elec plugs the same for the pumps?
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
the plugs are the same on both pumps so i suspect the differences will be small (assuming the pins have the same funcions)
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
ABS light should come on with ignition, and go out when the engine starts (same as the oil pressure light).
If it stays on, the most likely cause in the older system is a faulty voltage protection relay (the one near the ECU) which is easily damaged by voltage spikes like jump starting.
If the light goes out, then comes back on when you start moving, the fault is one of the wheel sensors or its connectors.
If it stays on, the most likely cause in the older system is a faulty voltage protection relay (the one near the ECU) which is easily damaged by voltage spikes like jump starting.
If the light goes out, then comes back on when you start moving, the fault is one of the wheel sensors or its connectors.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The external and internal wiring diagrams for the early and late ABS systems are identical. The difference is that the early system uses the additional relay to apply power to the system with ignition on, while the later system uses the main DME relay.
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
cheers brian, you're a legend!
i'll have a go at swapping the pump and ecu for theos known good ones today and see how i get on.
so on mine (later, no relay to blame) what would be the first culprit for the ABS light never going out (and no abs function)? where does the DME relay live and could this be to blame?
i'll have a go at swapping the pump and ecu for theos known good ones today and see how i get on.
so on mine (later, no relay to blame) what would be the first culprit for the ABS light never going out (and no abs function)? where does the DME relay live and could this be to blame?
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
I'm not saying the early pump and ECU are the same as the later ones - just that the pin connections are the same!
The extra relay on the early system contains some kind of voltage sensitive fuse arrangement, so the early ECU may be susceptible to voltage spikes without it.
I've never had to track down a permanently on ABS light on a later version, so I can't help you much there - although one of my own cars intermittently does it.
One of the relays in the ABS pump cold cause the problem, but I've changed both of them on mine for known good ones, and it hasn't solved mine.
The extra relay on the early system contains some kind of voltage sensitive fuse arrangement, so the early ECU may be susceptible to voltage spikes without it.
I've never had to track down a permanently on ABS light on a later version, so I can't help you much there - although one of my own cars intermittently does it.
One of the relays in the ABS pump cold cause the problem, but I've changed both of them on mine for known good ones, and it hasn't solved mine.
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
i changed the silver one on mine as it had burned out but there was no change. i now have a spare black one to try so i'll give that a go.
if i plug in the pump and ecu with no fluid ports connected, would this upset the system? only then i can change it all over to test things with no brake pipe hassle. would the pump throw up an error signal if it's not connected to the fluid?
if i plug in the pump and ecu with no fluid ports connected, would this upset the system? only then i can change it all over to test things with no brake pipe hassle. would the pump throw up an error signal if it's not connected to the fluid?
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Don't think the pump would appreciate running dry! Also, try not to get air into the internals of the ABS pump unit - it's not easy to get out. Officially needs a BMW diagnostic tool which pulses the solenoids to bleed it.
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
ooh, nasty!
if i just connect it up on the drive and fire the engine up, would the pump physically 'do' anything?
if i just connect it up on the drive and fire the engine up, would the pump physically 'do' anything?
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
