325i m20b25 jerky lumpy up to 3500rpm then loads of power

Need technical Q/A then you're in the right place

Moderator: martauto

abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Thu Feb 01, 2007 9:52 am

Ok car was running like a dog idle lumpy mpg crap rough running. Did compression check low on 1 and 2 exhaust leak on 6 and inlet manifold leak on 6. So removed head replaced headgasket and inlet manifold gasket and exhaust gaskets all good did compression check all identicle 12.5 on the gauge across the board excellent. Start it up lumpy idle smells rich stutters up to 3500 ish then fine. Ok so i change filter and plugs clean the ICV now stable idle 700 doesn't rise or drop but lumpy and the same running issue up to 3500. Now changed blue sensor and brown cleaned all connectors tps checked on multimeter checked injector loom have cleaned all connectors and sensors, still same running issue.

Change:
blue and brown temp sensors
rotor arm dissy cap plugs
thermostat
inlet gaskets
exhaust gaskets
head gasket and cam belt

I'm now looking to change AFM and leads but these are expensive and i would be gutted if they made no difference and also FPR.

Like I say after 3500rpm drives like a beast. I am situated in Cardiff does anybody have a 325i in the area I could try parts with? Or any other thoughts on what can cause this. I feel it is more of a fueling issue that ignition but i could be wrong. :cry:
If I can't fix it I'll f**k it up so bad nobody can!!
E30Mark
E30 Zone Team Member
E30 Zone Team Member
Posts: 8107
Joined: Sun Jan 09, 2005 11:00 pm
Location: Wimborne, Dorset

Post Thu Feb 01, 2007 9:57 am

Are you sure you setting the cam timing correct? sounds like you could be a tooth out....

My brother decided to re-assemble my old 323i as a favour when i was away one weekend, but he got the cam one tooth out.... like you say after 3.5 k it went like a rocket... luckily reset the cam timing and all was OK.
1 & 2 bed flats in Bournemouth areas, with parking
PM for details
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Thu Feb 01, 2007 10:01 am

Thats possible, would I still have good compression? How can I test without stripping it apart? Also forgot to say it's a motronic H reg.
If I can't fix it I'll f**k it up so bad nobody can!!
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Thu Feb 01, 2007 1:03 pm

OK off to pick up an inductive strobe to check the timing. Still open to ideas any thoughts let me know. Shall keep you posted as to progress. :D
If I can't fix it I'll f**k it up so bad nobody can!!
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Fri Feb 02, 2007 8:33 am

Checked the timing with a adjustable timing light last night it's at 12deg now can somebody confirm it should be 8deg as that would confirm to be a tooth out on the belt.
If I can't fix it I'll f**k it up so bad nobody can!!
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Sat Feb 03, 2007 8:33 pm

I stripped off the rad and rest of the front end crap to check the timing marks and their spot on so what the f is wrong with my stupid piece of junk :-x

Any chance of trying somebodys AFM with mine?
If I can't fix it I'll f**k it up so bad nobody can!!
ajm-e30
E30 Zone Regular
E30 Zone Regular
Posts: 472
Joined: Sat Nov 11, 2006 11:00 pm
Location: newport,land of sheep sh***ers

Post Sat Feb 03, 2007 8:36 pm

im in cardiff, gimme a shout if u get stuck mate
Image
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Sat Feb 03, 2007 8:51 pm

What are you doing tomorrow and where abouts in Cardiff are you I really need to swap out my afm and icv to see which I need to buy.
If I can't fix it I'll f**k it up so bad nobody can!!
ajm-e30
E30 Zone Regular
E30 Zone Regular
Posts: 472
Joined: Sat Nov 11, 2006 11:00 pm
Location: newport,land of sheep sh***ers

Post Sat Feb 03, 2007 8:58 pm

rhiwbina, not up to much tomorrow either, have u checked the inlet boot for cracks?? also the oil breather from the rocker cover can cause problems as well
Image
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Sat Feb 03, 2007 9:03 pm

Inlet boot is new and I can't here an air leak tryed spraying inlet area with wd40 to see change in revs sound but nothing.

I'm just by culverhouse cross wenvoe side
If I can't fix it I'll f**k it up so bad nobody can!!
ajm-e30
E30 Zone Regular
E30 Zone Regular
Posts: 472
Joined: Sat Nov 11, 2006 11:00 pm
Location: newport,land of sheep sh***ers

Post Sat Feb 03, 2007 9:07 pm

can meet u at national tyres on cowbridge road at about 11am if thats any good??
Image
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Sat Feb 03, 2007 9:16 pm

Can you pm me your phone number and I'll give you a call to figure something out.
If I can't fix it I'll f**k it up so bad nobody can!!
ajm-e30
E30 Zone Regular
E30 Zone Regular
Posts: 472
Joined: Sat Nov 11, 2006 11:00 pm
Location: newport,land of sheep sh***ers

Post Sat Feb 03, 2007 9:26 pm

u have pm
Image
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Sun Feb 04, 2007 7:39 pm

Thanks for the help ajm-e30 but still no luck runs like a bag of spanners need more ideas :?
If I can't fix it I'll f**k it up so bad nobody can!!
gareth
E30 Zone Team Member
E30 Zone Team Member
Posts: 11005
Joined: Tue Jan 11, 2005 11:00 pm
Location: hastings, east sussex

Post Sun Feb 04, 2007 7:47 pm

does the problem change when you remove the oil filler cap? it sounds like a large vacuum leak...?

maybe a sticky / gummed injector that only clears up at higher fuel pressures?

regarding cam timing, i can't remember how many teeth the cam pulley has but the difference in timing per tooth is 720 divided by the number of teeth on the cam pulley. this is because the cam runs at half crank speed, hence 360 degrees on the cam is 720 degrees on the crank.
Sole founder of Fe2O3-12V it's a lifestyle
Image
LSD rebuilding / modification services provided, PM for details
ajm-e30
E30 Zone Regular
E30 Zone Regular
Posts: 472
Joined: Sat Nov 11, 2006 11:00 pm
Location: newport,land of sheep sh***ers

Post Sun Feb 04, 2007 7:48 pm

try the fuel filter first mate
Image
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Mon Feb 05, 2007 8:57 am

Gonna change fuel fillter, FPR and vacuum hose to FPR. I have tried the oil cap but no problems there this is driving me nuts might have to take it to BMW for diagnostics :x
If I can't fix it I'll f**k it up so bad nobody can!!
ajm-e30
E30 Zone Regular
E30 Zone Regular
Posts: 472
Joined: Sat Nov 11, 2006 11:00 pm
Location: newport,land of sheep sh***ers

Post Mon Feb 05, 2007 1:38 pm

if ur gonna do that go to b&r mate, they will be much cheaper
Image
bobafett
E30 Zone Regular
E30 Zone Regular
Posts: 285
Joined: Tue Dec 12, 2006 11:00 pm
Location: Bristol

Post Mon Feb 05, 2007 1:49 pm

Whats the condition of the spark plugs ? ie are they wet with unburnt fuel after idling for a while ?
If so has your pressure reg rolled over and put its legs up in the air ?

So with it self righting after 3500 is the vacuum from the manifold equalling out on the diaphragm and then allowing correct fuel into the injector rail....?

Also was the bottom damper/vibration damper dropped on removal, if so check the teeth on the side for any indentations this will put a false reading up the sensor wire to the DME and confuse the hell out of the control unit. :eek:

Hope these ideas help mate ! :cool:
What ?! Drive straight officer......It's an E30 !
It's the Ultimate Drifting Machine.
abelai
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Aug 06, 2005 11:00 pm
Location: Cardiff

Post Wed Feb 21, 2007 3:47 pm

The problem was my injectors found by increasing the fuel pressure to force the injectors to close fully (pinching the fuel return) runs fine. One application of Cataclean later and problem solved. :D
If I can't fix it I'll f**k it up so bad nobody can!!
ajm-e30
E30 Zone Regular
E30 Zone Regular
Posts: 472
Joined: Sat Nov 11, 2006 11:00 pm
Location: newport,land of sheep sh***ers

Post Wed Feb 21, 2007 4:04 pm

sorted, so u drivin it now then??
Image