Changing the big Diff bush/ + CENTRE PROP BEARING?!

Need technical Q/A then you're in the right place

Moderator: martauto

Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Thu May 12, 2005 6:48 pm

Yo! Need to do mine before i go to the ring so any tips? my dad has a press at work but the back plate looks like nice and brittle aluminium.

So i fear it would be all to easy to break?

Cheers Si
Last edited by Simon13 on Sun May 15, 2005 1:08 pm, edited 1 time in total.
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Thu May 12, 2005 7:26 pm

Simon, the backplate is indeed a lil fragile, the bush only goes one way, the "hole" is slighty oval so no probs there, use the Z3 bushing as its a stronger design, go MZ if your wallet can stand it.

remove backplate,
gently warm the area surrounding the bush with a blowlamp.
use the new bush to press the old one through, can take 5 tons to get them moving though, I've seen higher on a couple without problems, the heat is the key dude.

If you want me to do for ya no worries, bring the bits and I'll do the honours :wink:
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Thu May 12, 2005 7:27 pm

I'd change it to the Z3M coupe bush rather than a standard E30 one.The coupe bush has got less cut outs/more rubber and metal ribs so makes it a bit stiffer.

Sorry i can't help with changing it,i didn't have access to a press so i took it to the garage to swap whilst the dif was being swapped from 3.25 to 3.64 ratio.

Image
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Thu May 12, 2005 8:58 pm

cheers guys, i have bought the ZM3 one as it was Ԛ£3 more than the normal E30 one, so it was rude not too! plus the 10% they give me for being a pest there!
martinclan
E30 Zone Newbie
E30 Zone Newbie
Posts: 171
Joined: Wed Jan 19, 2005 11:00 pm

Post Thu May 12, 2005 9:04 pm

I did mine without a press. I cut out the rubber inner then CAREFULLY hacksawed through the metal part so that it was ALMOST cut through. Then a few sharp tap with a hammer and cold chisel and out it popped - no drama. Make sure that the backplate is well supported though.

The new bush was easily tapped back in once I had gently cleaned up the hole where it goes.
Image
It's an E30 Jim but not as we know it...
User avatar
buster
E30 Zone Addict
E30 Zone Addict
Posts: 3779
Joined: Sun Jan 09, 2005 11:00 pm
Location: Near middlesbrough,Teesside

Post Thu May 12, 2005 9:10 pm

cheat and do what i did,replace it with a zm coupe cover !


Image
jamie325isport
E30 Zone Regular
E30 Zone Regular
Posts: 689
Joined: Sun Jan 16, 2005 11:00 pm
Location: W.Sussex

Post Thu May 12, 2005 9:27 pm

Nice one, how much was that then Buster? Also bit off topic i know but been meaning to ask for a while, what did you do to get the twin exit? They are both connected i take it. Was it an old E21 323 system? and does anyone know if they can be made to fit? (i know i will start a whole new thread) :offtopic:
Image

Wanted:- One Genuine 7J Alpina. PM me
User avatar
buster
E30 Zone Addict
E30 Zone Addict
Posts: 3779
Joined: Sun Jan 09, 2005 11:00 pm
Location: Near middlesbrough,Teesside

Post Fri May 13, 2005 1:29 pm

Ԛ£100 at the $tealer for the diff cover.

The exhaust;
i bought a e46 m3 back box.
then realised even with a bit of chopping it weren't going to fit !
I ve still got it in the shed !!

I then noticed ,twin exhausts could be fitted but would need to be further appart than in the pic to fit either side of the tyre well.I didn't like the look of that though i wanted them closer in.BUT this can't be done without chopping the tyre well out,so i never.

The pic is a photoshop chop !! its a fake ! Id love it to be like that ,maybe one day i might do it.
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Sun May 15, 2005 1:09 pm

when i change my centre prop dohnut thingy can i get the prop off at the diff end?! so i can do my diff bush at the same time?
Jos
E30 Zone Camper
E30 Zone Camper
Posts: 1104
Joined: Mon Jan 17, 2005 11:00 pm
Location: Belfast

Post Sun May 15, 2005 8:20 pm

I would recon you will have to drop the diff out to change the bush on it. Should be no issues getting the prop undone from either the box or the diff, the nuts on the guibo are quite tight though, do the diff end 1st using the gearbox to keep it inplace while you slacken them.

Nice idea on the Z3M cover, need to change my cover as its from an e23, and it's finned too! :)
'89 Touring - slightly rippled with a rusty underside
'94 e36 tree climber
95-540iLE
Zone Newbie
Posts: 185
Joined: Mon Jan 23, 2006 11:00 pm
Location: Hobart, Tasmania, Australia

Post Fri Feb 02, 2007 12:01 am

I know this is an old thread, but does anyone have the part number for the ZM finned cover bits?

Thanks
buster wrote:cheat and do what i did,replace it with a zm coupe cover !


Image
oze30
E30 Zone Addict
E30 Zone Addict
Posts: 4133
Joined: Mon Oct 24, 2005 11:00 pm
Location: Sydney

Post Fri Feb 02, 2007 2:52 am

95-540iLE
Zone Newbie
Posts: 185
Joined: Mon Jan 23, 2006 11:00 pm
Location: Hobart, Tasmania, Australia

Post Fri Feb 02, 2007 3:03 am

Thanks
oze30
E30 Zone Addict
E30 Zone Addict
Posts: 4133
Joined: Mon Oct 24, 2005 11:00 pm
Location: Sydney

Post Fri Feb 02, 2007 3:12 am

Though I'd check with BMW when youorder it.. Im not sure if the ones in teh diagram are finned! 8O
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Feb 02, 2007 9:05 am

oze30 wrote:Though I'd check with BMW when youorder it.. Im not sure if the ones in teh diagram are finned! 8O
The appearance of the cover in the ETK diagram may, or may not, bear any relation to what it looks like in real life. The diagram is just for identifying a diff rear cover.
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Fri Feb 02, 2007 9:19 am

Brianmoooore wrote:
oze30 wrote:Though I'd check with BMW when youorder it.. Im not sure if the ones in teh diagram are finned! 8O
The appearance of the cover in the ETK diagram may, or may not, bear any relation to what it looks like in real life. The diagram is just for identifying a diff rear cover.
Eg. M3 bodyshell shown without flared rear arches, etc.
Image