Front suspension help!!

Need technical Q/A then you're in the right place

Moderator: martauto

salami
E30 Zone Newbie
E30 Zone Newbie
Posts: 170
Joined: Sat Dec 02, 2006 11:00 pm
Location: Leicestershire

Post Sun Jan 28, 2007 12:13 pm

Im just about to swap my front inserts but looking at the haines manual it says i have to remove all sorts of things(brakes ,fluid ect..)can any one tell me what i can get away with removing??
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Sun Jan 28, 2007 12:16 pm

nothing... take the whole leg out. use PROPER tools to remove the spring and change the insert

its only a case of removing the brake calipers, undoing the sensors, removing the ball joint from the control arm and the steering rack and then undoing the top mount nuts so the leg comes out

its not a difficult job, just fairly time consuming.
Image
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Jan 28, 2007 12:19 pm

you only remove the brake calipers but dont disconnect them,leave them hanging,dont need to remove discs or pads,remove both ball joints and undo top mount nuts.then its just the top mount and springs to remove(use spring compressors for safety).the cap/nut holding the insert in can sometimes be a right cnut to remove but should shift with a set of stilson grips.
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Sun Jan 28, 2007 12:24 pm

Having just changed the front springs myself, I'd recommend loosening the top centre strut nut before you do anything else, with the car on its wheels on the ground; trying to undo it otherwise is practically impossible!
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Jan 28, 2007 12:26 pm

320iSE wrote:Having just changed the front springs myself, I'd recommend loosening the top centre strut nut before you do anything else, with the car on its wheels on the ground; trying to undo it otherwise is practically impossible!
yes, good point,i forgot that.i made up a special tool that allows me to do it easily when removed.
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Sun Jan 28, 2007 12:31 pm

Got any details on this special too, Fuzzy?
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
gareth
E30 Zone Team Member
E30 Zone Team Member
Posts: 11005
Joined: Tue Jan 11, 2005 11:00 pm
Location: hastings, east sussex

Post Sun Jan 28, 2007 12:34 pm

fuzzy wrote:
320iSE wrote:Having just changed the front springs myself, I'd recommend loosening the top centre strut nut before you do anything else, with the car on its wheels on the ground; trying to undo it otherwise is practically impossible!
yes, good point,i forgot that.i made up a special tool that allows me to do it easily when removed.
i always end up with some cobbled effort using a 1/4" square drive extension (with whatever fitting is needed to hold the shaft) through the centre of a large spark plug socket. then use a ring spanner on the outside of the socket. it's a good way of breaking 1/4" extension bars though, thankfully halfords have a lifetime warranty on their pro tools!!!! i've had 3 sets so far winkeye
Sole founder of Fe2O3-12V it's a lifestyle
Image
LSD rebuilding / modification services provided, PM for details
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Jan 28, 2007 12:35 pm

320iSE wrote:Got any details on this special too, Fuzzy?
i will go and take a pic,its just a socket with the back end cut out with a bar welded to the side allowing you access with a smaller socket to the little nut in the centre.
salami
E30 Zone Newbie
E30 Zone Newbie
Posts: 170
Joined: Sat Dec 02, 2006 11:00 pm
Location: Leicestershire

Post Sun Jan 28, 2007 1:02 pm

Nice one thanks! Just going to give it a go now! :D
salami
E30 Zone Newbie
E30 Zone Newbie
Posts: 170
Joined: Sat Dec 02, 2006 11:00 pm
Location: Leicestershire

Post Sun Jan 28, 2007 2:54 pm

Ok to take off the ball joints do they undo part way then they spin? and then do i need to use the splitter inbetween the ball joint and bottom of the strutt and afterwards how the poo do you get them back to gether?
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Jan 28, 2007 2:57 pm

salami wrote:Ok to take off the ball joints do they undo part way then they spin? and then do i need to use the splitter inbetween the ball joint and bottom of the strutt and afterwards how the poo do you get them back to gether?
easiest way is to put a jack under the balljoints and jack it up so the weight of the car pressing down on them stops them spinning.they just pop back in.
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Sun Jan 28, 2007 2:58 pm

i use a trolley jack on the bottom of the ball joint, to hold the stem still, then i remove the nut. to get the stem out of the hub, just twat the hub as hard as you can with a ball pein hammer and it should shock the stem out of the hub
Image
salami
E30 Zone Newbie
E30 Zone Newbie
Posts: 170
Joined: Sat Dec 02, 2006 11:00 pm
Location: Leicestershire

Post Sun Jan 28, 2007 3:44 pm

i will give it a go in the morning as beer is calling cheers :mad:
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Sun Jan 28, 2007 9:43 pm

I done my front shocks insert, top mounts and springs in about 4 hours, I watch Stu do it on my cab a while back and thought id give it ago myself and i enjoyed every minute of it.

The balljoint was a ball ache but with the jack underneath them and a big hammer it wasnt a problem, I did get to the stage though of thinking if i fart on the joint it would shock it better :lol:
Image
Considering Selling the Cabby, looks like its gonna go
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Sun Jan 28, 2007 9:56 pm

Joint splitters are the preferred method, but I managed to break mine after overtightening them with a stubborn joint! :(

An alternative method is to hit the flat machined section of the joint with a steel hammer, which 'shocks' the joint loose (that's what the flats are machined there for, in case you were wondering!)

If the joint still resists, heat with a blowtorch (directing the heat to the iron surrounding the joint), undo the joint nut to the end of the thread, and hit the nut (the nut protects the thread from damage.) Some 'Plus Gas' or WD40 soaked into the joints some hours before you attempt to undo them helps too.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Sun Jan 28, 2007 9:58 pm

Preffered method in mygarage

Image
Image
Considering Selling the Cabby, looks like its gonna go
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Sun Jan 28, 2007 10:04 pm

Satisfying things, aren't they :)
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Sun Jan 28, 2007 10:16 pm

320iSE im suprised u didnt notice it chrome hammer
Image
Considering Selling the Cabby, looks like its gonna go
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Sun Jan 28, 2007 10:22 pm

You must be using lots of chrome polish at this rate...why not get shares in Autosol? :idea:
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Sun Jan 28, 2007 10:26 pm

??????? bodgers alert? for the price of that hammer you can by a ball joint splitter? much easier :?
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Sun Jan 28, 2007 10:33 pm

Simon13 wrote:??????? bodgers alert? for the price of that hammer you can by a ball joint splitter? much easier :?
believe it or not mate, when i was at bmw, they refused to use any ball joint splitter at all; they just twated the side of the wishbone were the ball joint is as hard as they could an it pops out in one hit. :?
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Sun Jan 28, 2007 10:33 pm

Not necessarily: as I discovered, they can break if the joint's too tight, then you have to resort to other methods.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Sun Jan 28, 2007 11:24 pm

i tried a ball joint splitter and then soon after threw it across the garage :mad:
Image
Considering Selling the Cabby, looks like its gonna go
salami
E30 Zone Newbie
E30 Zone Newbie
Posts: 170
Joined: Sat Dec 02, 2006 11:00 pm
Location: Leicestershire

Post Mon Jan 29, 2007 10:57 am

front strutt is off but doesn't look like it has inserts??oh and the spring has snapped,i wonder if that would effect the handleing??? 8O
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Mon Jan 29, 2007 11:40 am

The strut should have a large 'ring' nut or collar at its top. Are they original BMW struts? (should have a logo somewhere.) Snapped spring is bad news! At least it should make it easier to remove though...
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Mon Jan 29, 2007 1:12 pm

ball joint splitters are for people that like to fanny about trying to do things methodically, as they believe it will get them further in life...

...hammers are for people who dont want to spend an extra 1/2 hour doing a job...
Image
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Mon Jan 29, 2007 1:27 pm

In the words of MC Hammer its
Hammer time
Image
Image
Considering Selling the Cabby, looks like its gonna go
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Mon Jan 29, 2007 2:36 pm

he's got your trouser's on neil...
Image
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Mon Jan 29, 2007 2:37 pm

stuartgallafant wrote:he's got your trouser's on neil...
i know thet look better on me though :cool:
Image
Considering Selling the Cabby, looks like its gonna go
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Mon Jan 29, 2007 2:38 pm

8O
Image
salami
E30 Zone Newbie
E30 Zone Newbie
Posts: 170
Joined: Sat Dec 02, 2006 11:00 pm
Location: Leicestershire

Post Mon Jan 29, 2007 3:21 pm

cliffybabe wrote:In the words of MC Hammer its
Hammer time
Image
My hero

anywho one leg off,one insert uninserted and a new one inserted :mad:
so just need some new springs and thats one side done hmmm this may take me more that 4 hours
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Mon Jan 29, 2007 4:04 pm

salami wrote:hmmm this may take me more that 4 hours
i think it already has, hasn't it!!
Image
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Mon Jan 29, 2007 4:06 pm

stuartgallafant wrote:
salami wrote:hmmm this may take me more that 4 hours
i think it already has, hasn't it!!
:lol: Stu ur so harsh, think of the sens eof achivement you'll have Salami when its back ont he ground with better front suspension winkeye
Image
Considering Selling the Cabby, looks like its gonna go
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Mon Jan 29, 2007 4:09 pm

neil, it was a tongue in cheek comment
Image
salami
E30 Zone Newbie
E30 Zone Newbie
Posts: 170
Joined: Sat Dec 02, 2006 11:00 pm
Location: Leicestershire

Post Mon Jan 29, 2007 4:18 pm

carn't wait ,ive just been spraying the legs and spray guard and im thinking of red for the calipers.

looks like i will have to wait a week for the springs as no where has them in......just enough time to get the other side off :roll: