Hi
are the all e30 have same wiring loom all around , electrics, dash board,
exept engine i should immagine.
why i'm asking , the point is that my car has 17 years now , so i was thinking to change wirinig loom in dors, dash board , torpedo, fuse box too.
can i use it from 325 320 for example? or it must be e30 m3 wiring loom.
many thanks
e30 wiring loom
Moderator: martauto
-
dn808e2
- E30 Zone Regular

- Posts: 499
- Joined: Sat Mar 11, 2006 11:00 pm
- Location: Kings lynn, Norfolk.
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
I should imagine that you could use around 90% from a normal E30....but the M3 aint a normal E30..... !!
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
E30 main car looms come in two flavours: check control version and non check control version. Also a little variation at the back of both for the touring looms, and, of course LH drive and RH drive.
Not familiar with the M3 body loom, but I can't see why it should be any different except for the addition of an oil temp wire.
Not familiar with the M3 body loom, but I can't see why it should be any different except for the addition of an oil temp wire.
-
dn808e2
- E30 Zone Regular

- Posts: 499
- Joined: Sat Mar 11, 2006 11:00 pm
- Location: Kings lynn, Norfolk.
many thanks .
i had bad connection in my car drivers door , i 've changed wiring loom in door , but i took it from
RHD car driver's side , and it went to driver's side on my car, strange but it woreked ,
mirror's regolator is on the left on LHD but here in Uk it's on right side .
i had bad connection in my car drivers door , i 've changed wiring loom in door , but i took it from
RHD car driver's side , and it went to driver's side on my car, strange but it woreked ,
mirror's regolator is on the left on LHD but here in Uk it's on right side .
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
New pins/sockets are available for the door plug and sockets. No need to change the whole loom, or hard wire through the hole in the connector provided for the purpose.
Locking/windows loom is (virtually) seperate from the main loom, and can be reversed in the car to suit LH or RH drive.
Locking/windows loom is (virtually) seperate from the main loom, and can be reversed in the car to suit LH or RH drive.
-
A1BMW325iSport
- E30 Zone Addict

- Posts: 4239
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Mid Wales
i've hard wired all my door wiring on both doors. i removed the pins/sockets and put lengths of wire in correct colours through each hole and soldered/heatshrinked them all. jobs a good un.
i have couple of complete wiring looms in garage spare so i just pinched wires from that.
i have couple of complete wiring looms in garage spare so i just pinched wires from that.
-
dn808e2
- E30 Zone Regular

- Posts: 499
- Joined: Sat Mar 11, 2006 11:00 pm
- Location: Kings lynn, Norfolk.
Thanks MEN
How can it be , i locked driver's side door and all around was locked , but when i lock the car from passanger's side all it lockes is passanger's side door and fuel lid

How can it be , i locked driver's side door and all around was locked , but when i lock the car from passanger's side all it lockes is passanger's side door and fuel lid

