Problems with changing alternator and steering belts

Need technical Q/A then you're in the right place

Moderator: martauto

NIX
E30 Zone Camper
E30 Zone Camper
Posts: 1409
Joined: Wed Jul 27, 2005 11:00 pm
Location: Twickenham

Post Sat Jan 13, 2007 4:40 pm

Right, last week I had a go at changing the steering and alternator/fan belt. Easy enough job. Get the AFM out the way (got a 325i), loosen or remove the tensioning bolts which should give enough slack to take the old belts off and the new ones on right? However, after loosening/removing the tensioning bolts, there seems to be no change in tension. A mate reckons that the pivot points had seized or something. So I tried spraying some WD40 around, tighten the bolts back up (but only finger tight) then drove for a week, hoping this would loosen things up. Just had another go today, and theres no change.

Any pointers, tips, anything? The squeeling from the fan belt really does my head in!

Cheers!

Nick
Image
SPADGE
Married to the E30 Zone
Married to the E30 Zone
Posts: 7373
Joined: Wed Aug 09, 2006 11:00 pm
Location: Milton Keynes, Bucks

Post Sat Jan 13, 2007 4:43 pm

Check my own quote of this post below :mad:
Last edited by SPADGE on Sat Jan 13, 2007 4:45 pm, edited 1 time in total.
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
SPADGE
Married to the E30 Zone
Married to the E30 Zone
Posts: 7373
Joined: Wed Aug 09, 2006 11:00 pm
Location: Milton Keynes, Bucks

Post Sat Jan 13, 2007 4:44 pm

SPADGE wrote:If the correct bolts are loose a bit of persuasion with a hammer is called for or a bar to supply a bit of leverage at the top of the alt to get it moving.
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
NIX
E30 Zone Camper
E30 Zone Camper
Posts: 1409
Joined: Wed Jul 27, 2005 11:00 pm
Location: Twickenham

Post Sat Jan 13, 2007 4:44 pm

Yeah tried a bit of hammer persuation but no luck, although maybe im not hitting the right parts?
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Jan 13, 2007 8:05 pm

Pivot bolts and the inner end of the adjusting straps may need to be slackened a little as well.
Don't slacken the locknuts on the adjusters more than just a little, or you will allow the adjuster pinion to ride out of the rack and chew the teeth up.
Hammers NOT required!
NIX
E30 Zone Camper
E30 Zone Camper
Posts: 1409
Joined: Wed Jul 27, 2005 11:00 pm
Location: Twickenham

Post Mon Jan 15, 2007 11:15 pm

Hi mate,

Thanks for the info. Do you know what size sockets I will need for the pivot bolts and the innner end of the adjusting straps? Are they easy to get to? Not sure which is what. Sorry for the novice talk but hey, I'm a novice.

Nick
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Jan 15, 2007 11:19 pm

13mm, 17mm and 19mm cover most things IIRC.
NIX
E30 Zone Camper
E30 Zone Camper
Posts: 1409
Joined: Wed Jul 27, 2005 11:00 pm
Location: Twickenham

Post Mon Jan 15, 2007 11:23 pm

Thanks mate! Will I have to undo anything to get to the other bolts or should it all be pretty much plane sailing once I get the AFM out the way?
Image
SPADGE
Married to the E30 Zone
Married to the E30 Zone
Posts: 7373
Joined: Wed Aug 09, 2006 11:00 pm
Location: Milton Keynes, Bucks

Post Tue Jan 16, 2007 12:12 am

NIX wrote:loosen or remove the tensioning bolts which should give enough slack to take the old belts off right? However, after loosening/removing the tensioning bolts
My earlier reply was made based on the above mate. I thought you had already loosened all the bolts.
Nothing wrong with using a hammer/lever for a bit of 'gentle' persuasion as long as your sensible with it and ALL the bolts are loose that need to be.
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
wildeian
E30 Zone Regular
E30 Zone Regular
Posts: 851
Joined: Thu Mar 09, 2006 11:00 pm
Location: Colchester, Essex

Post Tue Jan 16, 2007 12:48 am

I did this today Nix, 13mm for the PAS pump pivot, 13mm for the locknut that holds the 19mm adjuster, and I also had to undo the 13mm bolt holding the adjuster 'rail' to allow the pump to move fully out of the way!!

When they were loose/out, I pulled up on the belt and the pump moved!

IIRC alternator was the same/similar.


Whats this all about..........
Sorry for the novice talk but hey, I'm a novice.
NIX
E30 Zone Camper

:wink:
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jan 16, 2007 12:57 am

wildeian wrote:I did this today Nix, 13mm for the PAS pump pivot, 13mm for the locknut that holds the 19mm adjuster, and I also had to undo the 13mm bolt holding the adjuster 'rail' to allow the pump to move fully out of the way!!

When they were loose/out, I pulled up on the belt and the pump moved!

IIRC alternator was the same/similar.


Whats this all about..........
Sorry for the novice talk but hey, I'm a novice.
NIX
E30 Zone Camper

:wink:
The 17mm/19mm bolts are the ones to turn to slacken/tighten the belt.
NIX
E30 Zone Camper
E30 Zone Camper
Posts: 1409
Joined: Wed Jul 27, 2005 11:00 pm
Location: Twickenham

Post Tue Jan 16, 2007 9:08 am

Thanks to you all guys!

Much appreciated!

I know it should be a simple job, but when it comes to my car, nothing ever seems to be simple.

Wildeian - Yeah I know I've been around for a while but when it comes to the mechanics side of things I can do afew things but there are even some simple jobs I've just never had to tackle and therefore never learnt/looked up how to do :o: I can be handy with a set of tools at times but when it comes to my car I think I just give up too easily and go for the, fu#k it I'll have a cig and think of who else I can get to fix it. job done. lol :roll:
Image
wildeian
E30 Zone Regular
E30 Zone Regular
Posts: 851
Joined: Thu Mar 09, 2006 11:00 pm
Location: Colchester, Essex

Post Tue Jan 16, 2007 8:13 pm

Fair one Nix, just because eskimos are around snow all day, it doesn't mean they can ski!!! :D
NIX
E30 Zone Camper
E30 Zone Camper
Posts: 1409
Joined: Wed Jul 27, 2005 11:00 pm
Location: Twickenham

Post Tue Jan 16, 2007 9:19 pm

Exactamondo mate!

I studied car design at uni so I know how to make a car look nice but not so clued up on how to keep it running... :hammer:
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jan 16, 2007 9:24 pm

NIX wrote:but not so clued up on how to keep it running
And you never will if you don't get stuck in!
NIX
E30 Zone Camper
E30 Zone Camper
Posts: 1409
Joined: Wed Jul 27, 2005 11:00 pm
Location: Twickenham

Post Tue Jan 16, 2007 9:42 pm

Yeah I know mate but its hard round where I live coz its quite a narrow and surprisingly busy road, so getting under and around the car can be concerning. Not to mention my lack of tools, but im building that up with the more car work I attempt. Also my e30 is my only car, so if something goes wrong whilst im attempting to fix it, it can mean getting to work and other places becomes that much more of a mission if I dont fix it properly in time.

Anyways, excuses, excuses. Time to start reading more of the Haynes manual I got for christmas!
Image
NIX
E30 Zone Camper
E30 Zone Camper
Posts: 1409
Joined: Wed Jul 27, 2005 11:00 pm
Location: Twickenham

Post Tue Jan 16, 2007 10:49 pm

Actually Brian I've been meaning to ask. How come you know so much about e30s? I think you've nearly always been there to answer one of my questions in this section (much appreciated by the way). Is it just from working on them or are you/have been an official bmw mechanic of some sort?

Just interested to know :cool:

Nick
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jan 16, 2007 11:23 pm

Never worked for anyone other than myself.