325 slight misfire then stalled...now wont start!

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
eltel
E30 Zone Regular
E30 Zone Regular
Posts: 654
Joined: Wed Nov 09, 2005 11:00 pm
Location: mid wales

Post Fri Jan 12, 2007 6:16 pm

hi..few weeks ago i put on a thread about my 1988 325 saloon slightly misfiring once or twice whilst accelerating then would clear as fast as it came...now tonight whilst accelerating hard to overtake it again began to hesitate and miss slightly, like a fuel blockage almost kangarooing. it seemed worse on acceleration so nursed it home. put her in the garage where she idled and sounded sweet. with a slight rev at idle there was almost a slight miss down the exhaust but nothing excessive. but then it stalled and now wont start. cant seem to get any spark at plugs or from coil to dizzy. tested spark by putting a split pin in lead contact and placed over rocker cover..no spark!!!

any ideas anyone could it be a relay or coil or something?...turns over well but just wont fire.

any help appreciated
Only in the good lord we trust.. In everything else we check!!


1988 325i Tourer, Lowered, Deep Dish Alloys, Obc, Cruise Control, Heated Leather Sport Seats....
daveo
E30 Zone Newbie
E30 Zone Newbie
Posts: 60
Joined: Sun Dec 11, 2005 11:00 pm
Location: Chester ,Cheshire

Post Fri Jan 12, 2007 6:25 pm

The same thing hapened to me it turned out to be the fuel pump it might be worth testing it.

Dave
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Fri Jan 12, 2007 7:35 pm

check the wiring that runs behind the water pump pulley dude, it can chafe through and will cause all sorts of nasties to happen.

The loom is for the crank sensor and oil pressure switch BTW.

Assuming this is OK, try a new DME relay ( 5 pins under cover on NSF wing ) again, a known weakness on these and would cause what you've described.

HTH
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
User avatar
eltel
E30 Zone Regular
E30 Zone Regular
Posts: 654
Joined: Wed Nov 09, 2005 11:00 pm
Location: mid wales

Post Fri Jan 12, 2007 7:51 pm

will any 5 pin relay do or will it need to be the correct one from bmw?? thanks for that advice.... when i changed the head a while ago i did think that the crank sensor ran close to the pulley!
Only in the good lord we trust.. In everything else we check!!


1988 325i Tourer, Lowered, Deep Dish Alloys, Obc, Cruise Control, Heated Leather Sport Seats....
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Fri Jan 12, 2007 7:56 pm

Needs to be the correct rating dude, you can get these from GSF/ECP :thumb:
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Fri Jan 12, 2007 8:06 pm

Could be ignition coil - I had one crap out on me recently after initially causing intermittent misfires, poor starting, etc.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
User avatar
eltel
E30 Zone Regular
E30 Zone Regular
Posts: 654
Joined: Wed Nov 09, 2005 11:00 pm
Location: mid wales

Post Sat Jan 13, 2007 4:43 pm

tried my coil on mates car it and it ran fine..so coil must be ok...tried mates dme white relay but mine still did not start ..so not relay.

can see some chaffing on crank sensor wire by pulley's....but not worn totally through...could this cause no spark and stop car from starting???
Only in the good lord we trust.. In everything else we check!!


1988 325i Tourer, Lowered, Deep Dish Alloys, Obc, Cruise Control, Heated Leather Sport Seats....
User avatar
eltel
E30 Zone Regular
E30 Zone Regular
Posts: 654
Joined: Wed Nov 09, 2005 11:00 pm
Location: mid wales

Post Sun Jan 14, 2007 2:43 pm

just removed the crank sensor and found the 2 wires arew severed this must be the cause then??

the oil switch wire seems to be ok with slight chaffing on the insulation...what will happen if the oil wire wears through??
Only in the good lord we trust.. In everything else we check!!


1988 325i Tourer, Lowered, Deep Dish Alloys, Obc, Cruise Control, Heated Leather Sport Seats....
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Sun Jan 14, 2007 3:01 pm

new sensor required then, there are 3 wires, one is a screen that goes to ground the other are the VR output to the ECU, no output, no running simple as that dude, the black and yellow wires carry the signal iirc.

re the oil pressure wire, replace with a section of same gauge and all will be well

Sweet, sounds as though you'll be running again soon :thumb:
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 14, 2007 4:01 pm

If you're any good with a soldering iron and heat shrink sleeving you can repair the crank position sensor lead. Can be refitted to the car with the lead going over the top of the engine.
Be careful with the CPS lead near the sensor; it can get a bit brittle and crack if you bend it here.
User avatar
eltel
E30 Zone Regular
E30 Zone Regular
Posts: 654
Joined: Wed Nov 09, 2005 11:00 pm
Location: mid wales

Post Sun Jan 14, 2007 6:10 pm

thanks alot guys.... seems a bit of a silly way to route the sensor so close to the pulley's..will try to put it on another way!

cheers

gareth
Only in the good lord we trust.. In everything else we check!!


1988 325i Tourer, Lowered, Deep Dish Alloys, Obc, Cruise Control, Heated Leather Sport Seats....
Giggz
E30 Zone Camper
E30 Zone Camper
Posts: 1270
Joined: Wed Apr 13, 2005 11:00 pm
Location: East London

Post Sun Jan 14, 2007 6:21 pm

Let us know if you do source another way.

I would be particularly interested as i will be doing mine as soon as i recieve one!

Incidently when you say your car didnt start-did it turn over but just not fire up?

Cheers.
Image
^stolen but not forgotten^
User avatar
eltel
E30 Zone Regular
E30 Zone Regular
Posts: 654
Joined: Wed Nov 09, 2005 11:00 pm
Location: mid wales

Post Mon Jan 15, 2007 6:01 pm

yeah turned over fine just wouldn't fire!! awaiting new sensor to hopefully fix the fault
Only in the good lord we trust.. In everything else we check!!


1988 325i Tourer, Lowered, Deep Dish Alloys, Obc, Cruise Control, Heated Leather Sport Seats....
User avatar
eltel
E30 Zone Regular
E30 Zone Regular
Posts: 654
Joined: Wed Nov 09, 2005 11:00 pm
Location: mid wales

Post Wed Jan 17, 2007 4:41 pm

put the new crank sensor on and just routed it over the top of the rocker cover!!!

car starts and runs well again...thanks for all your help guys
Only in the good lord we trust.. In everything else we check!!


1988 325i Tourer, Lowered, Deep Dish Alloys, Obc, Cruise Control, Heated Leather Sport Seats....