Need technical Q/A then you're in the right place
Moderator: martauto
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
Post
Thu Jan 11, 2007 11:29 am
As it says chaps, if you could outline a brief step by step of getting the wings off that would help me out no end ...i have a plan

hahaha!

Best regards!
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
Post
Thu Jan 11, 2007 11:36 am
Remove:
Front bumper (2x T55 or 10mm bolts underneath)
Plastic arch liner (various 8mm screws)
Headlight surround grille (2x phillips screws and 3x clips)
Bumper support bracket (1 of 2x 10mm screws
Row of 8mm screws along top edge
2x screws below 'smiley' light unit (lower one is allen key - 4mm?)
2x 10mm screws inside wing, at door shut end
I think that's everything.
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
Post
Thu Jan 11, 2007 11:42 am
Much appreciated, i assume its a long drawn out process with much swearing, anything i need to be really careful about, in tearms of avoiding damage to the wing/fixings?
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
Post
Thu Jan 11, 2007 11:45 am
Not really a bad job - just remember to unplug the front indicators when you remove the bumper; cut the seam sealant at the scuttle and unplug the side repeater.
I also forgot an 8mm screw at the bottom of the arch, at the sill!
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
Post
Thu Jan 11, 2007 12:01 pm
Thats much appreciated!
Best regards
-
jcjdavis1
- E30 Zone Camper

- Posts: 1128
- Joined: Thu Apr 13, 2006 11:00 pm
- Location: Paisley Scotland
Post
Thu Jan 11, 2007 8:04 pm
Hi I think you might get some comments about the USS Enterprise,a wee bit big.

-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Fri Jan 12, 2007 12:43 am
Plastic bits under the wheelarch are the worst part of the job - assyuming that the bumper bolts are nicely copper greased, and, yes, if you could make the "Enterprise" a little smaller, please.
-
kevin316i
- E30 Zone Regular

- Posts: 783
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Fri Jan 12, 2007 1:37 pm
The plastic nuts at the top of the underside of the plastic wheelarch liner are likely to be seized. Suggest some WD40 on these before trying to remove them, otherwise the studs may break off.
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
Post
Fri Jan 12, 2007 3:26 pm
Much appreciated chaps, very helpful, can't resize that avatar so replaced with old school Enterprise

-
ian332isport
- E30 Zone Team Member

- Posts: 5380
- Joined: Wed Dec 22, 2004 11:00 pm
- Location: West Sussex
Post
Sat Jan 13, 2007 2:40 pm
goosiegander wrote:Much appreciated chaps, very helpful, can't resize that avatar so replaced with old school Enterprise

Still a bit big though

If it aint broke - Modify it...
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
Post
Sat Jan 13, 2007 2:53 pm
Well thats the best i can do for now, need to develop those editing skills i guess...
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Sat Jan 13, 2007 6:19 pm
Someone's done it, 'cause it's spot on now!