central locking

Need technical Q/A then you're in the right place

Moderator: martauto

markevans
E30 Zone Newbie
E30 Zone Newbie
Posts: 29
Joined: Tue Jan 02, 2007 11:00 pm
Location: newport, shropshire

Post Mon Jan 08, 2007 10:03 pm

hi me again ive been having trouble with my central locking it fried unit and sevos so replaced them all from a scrap car and done thr red/black wire join but still doors will only lock via central locking and not open via central locking , central locking relay is buzzing when trying to open anybody have any ideas could this box be faulty and is one of the red/black wires slighty thiner than other one please help i want to put carpet in soon someone help please i want my car back on the road
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Jan 08, 2007 11:50 pm

Can't remember if the red/black wires are exactly the same size or not, but you should have removed two seperate red/black wires from to seperate pins on the door pillar socket and joined them together.
Pull your locking ECU out of its hiding place, and remove it from its connector.
Using two short pieces of wire into the connector, link the brown and the white, then momentarily link the red/black and the blue. This should lock all the doors.
Now link the brown to the blue, and momentarily link the red/black to the white. This should unlock the doors.
markevans
E30 Zone Newbie
E30 Zone Newbie
Posts: 29
Joined: Tue Jan 02, 2007 11:00 pm
Location: newport, shropshire

Post Tue Jan 09, 2007 10:00 pm

Brianmoooore wrote:Can't remember if the red/black wires are exactly the same size or not, but you should have removed two seperate red/black wires from to seperate pins on the door pillar socket and joined them together.
Pull your locking ECU out of its hiding place, and remove it from its connector.
Using two short pieces of wire into the connector, link the brown and the white, then momentarily link the red/black and the blue. This should lock all the doors.
Now link the brown to the blue, and momentarily link the red/black to the white. This should unlock the doors.
have tried this and does the same as above any ideas y
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jan 09, 2007 11:26 pm

If it does as above, and you can hear the locking trying to work (i.e. it's getting the lock and unlock request signal), then I'm afraid you have another duff ECU.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jan 09, 2007 11:44 pm

Just seen your PM. What do you mean by "above"?
I read your last post as saying that it locks and unlocks properly with the wire links, but the PM says it still doesn't unlock.
Which way is it?
markevans
E30 Zone Newbie
E30 Zone Newbie
Posts: 29
Joined: Tue Jan 02, 2007 11:00 pm
Location: newport, shropshire

Post Wed Jan 10, 2007 9:16 am

Brianmoooore wrote:Just seen your PM. What do you mean by "above"?
I read your last post as saying that it locks and unlocks properly with the wire links, but the PM says it still doesn't unlock.
Which way is it?
sorry about the miss understanding, when i use the key the doors lock via central locking but dont open via central locking so tried the idea with the bridge wires and doors lock when bridged but dont unlock when bridged so doing the same either when using control box or bridging wires
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 10, 2007 9:37 am

In that case it's probably not the ECU
Check the voltage across the red/black and brown wires as you try to operate the locks.
Run a wire directly from battery + to the red/black terminal on the locking ECU to see if that dramatically improves things.(Care required, as this is bypassing fuses!)
Try unplugging the door/boot/fuel flap locking motors one at a time.
markevans
E30 Zone Newbie
E30 Zone Newbie
Posts: 29
Joined: Tue Jan 02, 2007 11:00 pm
Location: newport, shropshire

Post Wed Jan 10, 2007 11:48 am

Brianmoooore wrote:In that case it's probably not the ECU
Check the voltage across the red/black and brown wires as you try to operate the locks.
Run a wire directly from battery + to the red/black terminal on the locking ECU to see if that dramatically improves things.(Care required, as this is bypassing fuses!)
Try unplugging the door/boot/fuel flap locking motors one at a time.
just tried the direct power feed and all worked what does this mean
DaveGT
E30 Zone Regular
E30 Zone Regular
Posts: 333
Joined: Fri Dec 15, 2006 11:00 pm
Location: Northamptonshire

Post Wed Jan 10, 2007 11:52 am

I had issues with my central locking, I'm busy replacing the whole set up with a new remote locking kit and so far it's all going in really well and is very straight forward to fit! Just saves messing round and the remote locking is a bonus
Health and Safety Officer: "What would happen if a cameraman were to slip over?"
Clarkson: "Well, he'd probably have to stand back up again"
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 10, 2007 12:13 pm

DaveGT wrote:I had issues with my central locking, I'm busy replacing the whole set up with a new remote locking kit and so far it's all going in really well and is very straight forward to fit! Just saves messing round and the remote locking is a bonus
For remote locking to work, the OE central locking has to be in working order.
DaveGT
E30 Zone Regular
E30 Zone Regular
Posts: 333
Joined: Fri Dec 15, 2006 11:00 pm
Location: Northamptonshire

Post Wed Jan 10, 2007 2:45 pm

DaveGT wrote:
I had issues with my central locking, I'm busy replacing the whole set up with a new remote locking kit and so far it's all going in really well and is very straight forward to fit! Just saves messing round and the remote locking is a bonus
For remote locking to work, the OE central locking has to be in working order.

True, Hence why I'm busy REPLACING THE WHOLE SET UP. All the wiring, all the motors etc with after market parts. Easy to fit just fiddly to feed all the cabling to where you want it. The whole system connects to one control box which only has a positive and earth to connect to the car, the system can also be connected to any existing alarm system to work on the original fob
Health and Safety Officer: "What would happen if a cameraman were to slip over?"
Clarkson: "Well, he'd probably have to stand back up again"
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 10, 2007 3:26 pm

Do you really think that any aftermarket (probably Chinese) stuff even comes close to the quality, durability and reliability of the BMW OE stuff??
The OE system rarely gives trouble once the well known power feed problem to the ECU has been dealt with, and any other problems that arise are usually due to lack of general vehicle maintenance, allowing the sill drains to block, and flooding the ECU.
This has to be the daftest idea of the year on the zone so far!
DaveGT
E30 Zone Regular
E30 Zone Regular
Posts: 333
Joined: Fri Dec 15, 2006 11:00 pm
Location: Northamptonshire

Post Wed Jan 10, 2007 6:48 pm

Steady on, for a start you don't know the car or the issues with it so before you pass comment maybe you should ask for the full picture!!

I did all the usual, replaced all the original parts only to end up with part of the central locking loom shorting out and "melting". After much testing I gave up trying to trace the fault!

Yes I'm sure that the aftermarket kit I'm fitting is of a lower quality than a bmw kit but the kit on the car is 20 years old, wet, corroding and generally in need of replacment so from my point of view a new working replacement kit is better than a faulty original kit or a poor repair.
Health and Safety Officer: "What would happen if a cameraman were to slip over?"
Clarkson: "Well, he'd probably have to stand back up again"
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 10, 2007 7:11 pm

Replacement or repair of the original loom has got to be easier than fitting aftermarket stuff, and 20 year old BMW kit should be absolutely as new. In far better condition than the equivalent gear on a two year old Ford or some French crap for instance.
If the locking ECU is corroded, it's because the sills have been flooded.
It's all ultra reliable, so second hand availability far exceeds demand, keeping prices down.
DaveGT
E30 Zone Regular
E30 Zone Regular
Posts: 333
Joined: Fri Dec 15, 2006 11:00 pm
Location: Northamptonshire

Post Wed Jan 10, 2007 7:33 pm

The after market kit was very easy to fit, All part have been mounted in the same position as the original parts, If i had time to source second hand parts maybe i would have done but for me it's far easier to buy new, original or not, plus the kit has the added bonus of remote locking.
Health and Safety Officer: "What would happen if a cameraman were to slip over?"
Clarkson: "Well, he'd probably have to stand back up again"
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 10, 2007 7:42 pm

DaveGT wrote:The after market kit was very easy to fit, All part have been mounted in the same position as the original parts, If i had time to source second hand parts maybe i would have done but for me it's far easier to buy new, original or not, plus the kit has the added bonus of remote locking.
As you wish. It'll probably last until the warranty expires.
One request in the parts wanted forum, and you'd have been deluged with offers for every part you need.
User avatar
fugazi33
E30 Zone Newbie
E30 Zone Newbie
Posts: 213
Joined: Sat Sep 09, 2006 11:00 pm
Location: Bucks

Post Wed Jan 10, 2007 7:54 pm

Brianmoooore wrote:
DaveGT wrote:The after market kit was very easy to fit, All part have been mounted in the same position as the original parts, If i had time to source second hand parts maybe i would have done but for me it's far easier to buy new, original or not, plus the kit has the added bonus of remote locking.
As you wish. It'll probably last until the warranty expires.
One request in the parts wanted forum, and you'd have been deluged with offers for every part you need.
Hope it lasts longer than the aftermarket kit I wasted my time fitting in my Golf, 3 months :mad:
DaveGT
E30 Zone Regular
E30 Zone Regular
Posts: 333
Joined: Fri Dec 15, 2006 11:00 pm
Location: Northamptonshire

Post Wed Jan 10, 2007 8:30 pm

Well it's in the car now and din't take more than two or three hours to fit so we'll see what happens, it wasn't a cheap "chinese" kit so i'll guess i'll have to waiit and see!
Health and Safety Officer: "What would happen if a cameraman were to slip over?"
Clarkson: "Well, he'd probably have to stand back up again"
markevans
E30 Zone Newbie
E30 Zone Newbie
Posts: 29
Joined: Tue Jan 02, 2007 11:00 pm
Location: newport, shropshire

Post Fri Jan 12, 2007 9:15 am

Brianmoooore wrote:In that case it's probably not the ECU
Check the voltage across the red/black and brown wires as you try to operate the locks.
Run a wire directly from battery + to the red/black terminal on the locking ECU to see if that dramatically improves things.(Care required, as this is bypassing fuses!)
Try unplugging the door/boot/fuel flap locking motors one at a time.
just put volt meter on red/black wire and getting same reading as when i put volt meter agcross batterey, but when i run wire from batterey to red/black wire on unit the locking all works is that strange or what should i wire in an extra supply line to the unit or is there something else i could do
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Jan 12, 2007 9:24 am

You need to measure the voltage on the red/black wire at the lock ECU when the locking is trying to work, or connect a 12V 21W bulb across the red/black and brown.
Meter readings with no load are meaningless.
markevans
E30 Zone Newbie
E30 Zone Newbie
Posts: 29
Joined: Tue Jan 02, 2007 11:00 pm
Location: newport, shropshire

Post Fri Jan 12, 2007 9:37 am

Brianmoooore wrote:You need to measure the voltage on the red/black wire at the lock ECU when the locking is trying to work, or connect a 12V 21W bulb across the red/black and brown.
Meter readings with no load are meaningless.
have taken reading goes as follows 12.71 when not in use 10.17 when trying to operate