third post today, what a pest i am -just checked both caps as have just topped up coolant AGAIN (its needing topping up every 100-200 miles) to my intense dismay i discovered gunk inside the top of both caps, while the car may have been used twice in the last 7 weeks (-i've been off at sea) i'd have thought any condensation would have gone after 50 miles...
Am i in fact looking at a new head gasket?
Over to you...
Goosie
gunk in oil cap, gunk in coolant cap... i think i'm Fuc*ed!
Moderator: martauto
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Possible HeadGasket.....
What engine is it ?
What engine is it ?
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
Its the M20 320i any idea what it could cost me?
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
All in or just for the Head gasket ?
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
all in,
-though i live practically next door to motormec so getting parts ain't a problem,
Whatcha recommend?
-though i live practically next door to motormec so getting parts ain't a problem,
Whatcha recommend?
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
all in, without a newer head, id say around £150-200.
I have just finished a near complete top end refurb of my M20B25....
It cost me £300, thats for another head, skimming/recon/fit new cam shaft in head, full head gasket set, new head bolts, new cam belt and tensioner.
I have just finished a near complete top end refurb of my M20B25....
It cost me £300, thats for another head, skimming/recon/fit new cam shaft in head, full head gasket set, new head bolts, new cam belt and tensioner.
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
cool! was that your own work or did you take it to a specialist?
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
so any other advice or opinions people? 
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
yeah, before spunking a load of wedge on replacing headgasket etc, or at least to buy you some time until you can make arrangements or have the funds, get a bottle of Kalimex K-Seal www.kalimex.co.uk
this stuff really works and is guaranteed for the life of the engine, just pour it in the expansion tank and 3 mins later no more headgasket probs, need to ideally flush the system out first to get rid of oil and shyte out the system and put some fresh antifreeze in.
For £8 a bottle I would look no further. Buy this stuff, do not buy radweld or other shyte.
Gives you another option at least, some on here will disagree and say do the whole job, it's upto you. I fixed my car with this and I know of many others who have had excellent results.
this stuff really works and is guaranteed for the life of the engine, just pour it in the expansion tank and 3 mins later no more headgasket probs, need to ideally flush the system out first to get rid of oil and shyte out the system and put some fresh antifreeze in.
For £8 a bottle I would look no further. Buy this stuff, do not buy radweld or other shyte.
Gives you another option at least, some on here will disagree and say do the whole job, it's upto you. I fixed my car with this and I know of many others who have had excellent results.
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
good advice, i'll get some and try it, can't hurt 
-
johnna
- E30Zone Irregular
- Posts: 1715
- Joined: Sat Sep 17, 2005 11:00 pm
- Location: In the hole
Woah there!
Get hoses checked (for coolant leaks), get a compression test and carry out a service first, swapping oil and coolant costs the same as two rounds of drinks!!! Then see if the gunk comes back after a few longer runs. I have never come across Kalimex (or her sister) but I am suspicious of 'snake oils'...
Get hoses checked (for coolant leaks), get a compression test and carry out a service first, swapping oil and coolant costs the same as two rounds of drinks!!! Then see if the gunk comes back after a few longer runs. I have never come across Kalimex (or her sister) but I am suspicious of 'snake oils'...
Be a man for once in your life and sh!t in that boot!- Wilfred.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
As johna says, don't assume there is anything seriously wrong on the strength of a bit of gunk under the oil cap.
Gunge appearing in the coolant bottle is a bit more worrying though.
IF there is anything wrong at the top end of the engine, it's more likely to be a cracked cam bearing than the head gasket.
Get the car up to temp, take the rocker cover off, plug the vent hose and start the car. Look carefully at the bottom of the rearmost two cam bearings. If there is a crank, you can often see beads of water emerging from the bearing when the cooling system is up to pressure.
Watch the cam locking plate at the front of the engine doesn't work loose.
Gunge appearing in the coolant bottle is a bit more worrying though.
IF there is anything wrong at the top end of the engine, it's more likely to be a cracked cam bearing than the head gasket.
Get the car up to temp, take the rocker cover off, plug the vent hose and start the car. Look carefully at the bottom of the rearmost two cam bearings. If there is a crank, you can often see beads of water emerging from the bearing when the cooling system is up to pressure.
Watch the cam locking plate at the front of the engine doesn't work loose.
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
Cheers 
Any ball park figures for inspection and repair costs?
Any ball park figures for inspection and repair costs?
