Argggh - engine rattle + oil spray bar

Need technical Q/A then you're in the right place

Moderator: martauto

Two_Sheds
E30 Zone Newbie
E30 Zone Newbie
Posts: 102
Joined: Thu Oct 26, 2006 11:00 pm
Location: Stroud/Fife

Post Sat Jan 06, 2007 1:11 pm

Was trying to sort out the slight tappety noise in my 325, having adjusted the valve spacings to no avail, I decided to replace the oil spray bar. This seemed to quieten things down a bit, so I was happy. The next day I drove it down to my mates house to give him a lift, and I gave it some beans - now there is a horrendous, really loud rattle coming from the engine.

The worst thing is, I had to drive it 10 miles to get to my destination before I could stop, and I've got to drive it another 5 miles back to my house where I can work on it :eek:

Obviously I've not had a chance to look at it yet, but I was wondering if any of you might know what it might be and if it will have caused any permanent damage? What I suspect is that when I revved it high, its popped the oil spray bar off at one side leading to the rockers getting starved of oil and knocking against each other.

It all sounds really unhealthy, hopefully it will be fixable and not permanent, unfortunately I still have to drive it these 5 miles before I can even take a look at it though :cry:

Any thoughts?
User avatar
eltel
E30 Zone Regular
E30 Zone Regular
Posts: 654
Joined: Wed Nov 09, 2005 11:00 pm
Location: mid wales

Post Sat Jan 06, 2007 5:10 pm

i would say that maybe the bar is at fault...but more than likely you left one of the 10mm lock nuts a bit loose and the reving has moved the eccentric cam slightly thus incorrect gap!!

or

shortly after doing my valves for the same reason...one of the 6mm threaded bars broke whilst driving..the captive end with the flat came away from the bar again meaning that the eccentric cam could move freely.

whip the top off and have a gander!!
Only in the good lord we trust.. In everything else we check!!


1988 325i Tourer, Lowered, Deep Dish Alloys, Obc, Cruise Control, Heated Leather Sport Seats....
Two_Sheds
E30 Zone Newbie
E30 Zone Newbie
Posts: 102
Joined: Thu Oct 26, 2006 11:00 pm
Location: Stroud/Fife

Post Sat Jan 06, 2007 6:01 pm

Will do it tommorow, going to drive it very gingerly back home. I doubt its the valve spacings as I did them months ago (although to be fair, I don't drive the car very much as its a track car I keep in a lockup, so it could've come loose by now). Been going nuts thinking about what it could be and what sort of damage it might have done, will see tommorow I guess!

Thanks for the reply, expect some updates tommorow :) ...
Two_Sheds
E30 Zone Newbie
E30 Zone Newbie
Posts: 102
Joined: Thu Oct 26, 2006 11:00 pm
Location: Stroud/Fife

Post Sun Jan 07, 2007 3:21 pm

Right I've whipped off the rocker cover and started it up, and not even a drop of oil is dripping out of the oil spray bar (which I've just replaced). I took it off again and sprayed carb cleaner down it and there are definitely no blockages in it. So what the hell is going on? Its gone from working fine but fairly tappety with the old oil spray bar, to working even better with the new one for about a day and now no oil is getting through at all!

Please help!
Two_Sheds
E30 Zone Newbie
E30 Zone Newbie
Posts: 102
Joined: Thu Oct 26, 2006 11:00 pm
Location: Stroud/Fife

Post Sun Jan 07, 2007 3:37 pm

Just took the spray bar off and started it up, pissed oil everywhere so I don't think its internally blocked. I tried it again with the spray bar on and I noticed something weird - there was a big slow flow of oil beneath where the oil spray bar is connected at the front of the engine, but it wasn't coming from the threads around the oil spray bar itself - however, this didn't happen at the rear of the engine as far as I could see.

Another thing I've noticed is that the oil spray bar physically won't tighten all the way down to the the bottom, theres about 2 threads before it'd be fully flush. The previous oil spray bar was flush, but we couldn't get it off without snipping it in two so we could get a ratchet spanner over it. Could this be the problem - that it isn't tightly sealed enough?
Martinaston
E30 Zone Addict
E30 Zone Addict
Posts: 3749
Joined: Mon Mar 14, 2005 11:00 pm
Location: London

Post Sun Jan 07, 2007 3:55 pm

They have to be done up pretty tight normaly to deform the pipe to get a good seal, are you sure its not a piece of the old one stuck in the hole ?
I don't think the bolt screws down flush to the head though.
There is NO nucleus.
Two_Sheds
E30 Zone Newbie
E30 Zone Newbie
Posts: 102
Joined: Thu Oct 26, 2006 11:00 pm
Location: Stroud/Fife

Post Sun Jan 07, 2007 4:04 pm

Just done it up tighter and oil appears to be coming through now in drips, though its still flooding through at the front of the engine and not at the back. However, the nasty rattle is still there, so I'm going to wait for the car to cool then do the valve adjustments again and see what happens.

Getting more and more worried that I've permanently damaged it now :cry:
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 07, 2007 5:59 pm

Is the locking plate for the two rocker shafts still in place at the front of the head?
Two_Sheds
E30 Zone Newbie
E30 Zone Newbie
Posts: 102
Joined: Thu Oct 26, 2006 11:00 pm
Location: Stroud/Fife

Post Sun Jan 07, 2007 7:06 pm

Checked that Brian and it was still in place - btw, I reckon you should be in the new year's honours list or something, the amount of threads I've been reading where you've sorted stuff out for people is unbelievable!

Anyway, I was doing the valve clearances and got to the 2nd cylinder inlet (i think thats right, its the row of valves closest to the drivers side and second from the front of the car [sorry, i'm a complete mechanical imbecile]) and noticed that there was a massive gap - but on closer inspection, I noticed there was no gap because the rocker had slid along the shaft towards the front of the car and was no longer hitting the centre of the valve!

So I presume I've got to slide it back, is this a job I can do myself?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 07, 2007 7:16 pm

There should be clips locating the rockers. Big U shaped things that fit right across the rocker.
Should slide back easily as long as the cam isn't trying to open that particular valve.
BTW, if the locking plate is left out, the rocker shaft will turn and cut off all oil supply to the rockers and cam.
Two_Sheds
E30 Zone Newbie
E30 Zone Newbie
Posts: 102
Joined: Thu Oct 26, 2006 11:00 pm
Location: Stroud/Fife

Post Sun Jan 07, 2007 8:08 pm

Right, slid the rocker back with no bother at all and readjusted the valve clearance, started it up but it wouldn't fire, realised I'd never reconnected the spark plugs (told you I was a mechanical thicko!), did that and it started on the first stroke and sounded lovely! So thanks for helping through that one - I possibly nudged the clip holding it when I put the oil spray bar on with my big ham fists...

BUT!

That locking plate you were talking about appears to have moved out of position - the two rocker shafts appear to have rotated, so the two grooves that hold the plate in place are no longer "in sync", hence the plate either sticks out at one side a lot, or a little at both sides - meaning I can't get the rocker cover back on!!!

Is the an easy way to re-rotate the shafts so I can get the plate back in? Or is are they supposed to be out of line and I'm supposed to force the plate in?!

To get this far and then be thrown by the rocker cover not going back on is rather frustrating to be honest

Thanks again
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Jan 07, 2007 8:27 pm

Rocker shafts shouldn't be difficult turn. There's a slot in the plug at each end of the shafts that you can use, or a pair of grips on an unused part of the shaft wouldn't do much harm. Not until you try to remove the shaft, anyway!
Two_Sheds
E30 Zone Newbie
E30 Zone Newbie
Posts: 102
Joined: Thu Oct 26, 2006 11:00 pm
Location: Stroud/Fife

Post Sun Jan 07, 2007 8:55 pm

Got everything pieced back together, just letting it idle for 10 minutes now to make sure everythings OK - would just like to say thank you all very much for your help (especially you Brian) - sorry to double check something as simple as rotating the rocker shafts with mole grips, but I don't want to make anything worse than it already is!

Going to tackle the broken window and associated rust hole tommorow hopefully, might start getting it out now :cool: