Leaking heater matrix how hard to change or fix?

Need technical Q/A then you're in the right place

Moderator: martauto

DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Dec 22, 2006 12:26 pm

i have a L reg E30 cab and the heater matrix is leaking a bit
is it hard to swap the unit with other one?
or can i fix my existing one?
also is it a hard job and does it envolve draining the cooling system
Last edited by DJ_B4L on Wed Jan 03, 2007 7:57 pm, edited 1 time in total.
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Wed Jan 03, 2007 7:18 pm

any one?
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 03, 2007 8:59 pm

Heater matrix slides out the left hand side of the heater, but fouls the bellcrank arrangement for the brake cylinder a little, IIRC.
You don't need to drain the entire coolant as such, but you need to remove both heater hoses from the bulkhead under the bonnet and tie them high enough to stop coolant coming out. Then take a piece of garden hose, put in on the lower heater spigot and blow through it to remove as much coolant as possible from the matrix.
Once you get the glovebox access panels and the centre console out the way it's fairly obvious how it comes apart.
Sure it's the matrix and not the electric heater valve.
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Wed Jan 03, 2007 9:03 pm

I would try a leak inhibitor like "bars seal' 1st.
Image
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Wed Jan 03, 2007 9:19 pm

which ones which any one have a pic? im going to check it out and get back to you i have taken the centre console off already and glovebox panels
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Jan 05, 2007 12:54 am

brian is this the electric heater valve this is what is leaking
Image
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Jan 05, 2007 12:57 am

that white and black thing is leaking where it joins and also its got some kind of funny looking thing in between
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Jan 05, 2007 1:03 am

DJ_B4L wrote:brian is this the electric heater valve this is what is leaking
Image
That's the valve, and it looks like it's split at the riveted join as they usually do.
Tape those little square nuts in place when you fit the new one.
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Jan 05, 2007 1:08 am

any idea how much they are also

cant the old one be fixed? any way of sealing it?
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Jan 05, 2007 8:55 am

I've never tried to repair one, because they are readily available from scrap E30s.
They seem to suffer from the rivets pulling through, so I suppose you could try removing their remains and replacing them with four suitable nuts and bolts.
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Jan 05, 2007 9:57 am

whats the reason for them rivets pulling through? is it the pressure of the water or something else?

how hard is it to take this valve out? do i have to undo all the screws i see on this

also if i was to get one from another e30, are they all the same or will i need to look for a specific one?

thanks
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
BMW_YARD
E30 Zone Newbie
E30 Zone Newbie
Posts: 146
Joined: Sun Jun 25, 2006 11:00 pm

Post Fri Jan 05, 2007 10:24 am

I've got a couple of good ones here, if you show me a good picture (just pull back a bit on the one you have taken) I'll check I've got the right one for you.
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Jan 05, 2007 10:49 am

no probs mate il add it after wrk

what did you want for it?
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
BMW_YARD
E30 Zone Newbie
E30 Zone Newbie
Posts: 146
Joined: Sun Jun 25, 2006 11:00 pm

Post Fri Jan 05, 2007 10:58 am

£5
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Jan 05, 2007 11:14 am

is that including delivery were abouts are you located
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Jan 05, 2007 11:22 pm

DJ_B4L wrote:whats the reason for them rivets pulling through? is it the pressure of the water or something else?
There was a safety recall on E30s and several other BMWs several years ago concerning the pressure cap for the cooling system.
The original type could fail and over pressurise the cooling system, causing the end seals of the radiator to fail, a hose to blow, or the rivets on this valve to fail, in which case boiling coolant could be deposited on the passengers (or drivers, LHD) legs.
Check that your cap has been replaced.
User avatar
exup
Boost Junkie
Posts: 351
Joined: Tue Mar 08, 2005 11:00 pm

Post Fri Jan 05, 2007 11:32 pm

How can u tell if the caps been replced / got the correct one on it ? :mad:
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Jan 05, 2007 11:44 pm

All the replacement caps I've had from my dealer have had a yellow disc on their bottom, but from a thread on here once, it appears that there may be a replacement cap with a black underside as well, but with different markings from the original.
Give the last seven digits of the VIN to your dealer, and they should be able to tell you if its been replaced, although that doesn't necessarily mean that the cap is still on the car.
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Feb 02, 2007 2:13 am

how do you undo all the screws to take the electric heater valve off
there are some that are right at the end but face the out towards the engine bay i cant reach these?
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Feb 02, 2007 8:57 am

Only three screws involved, IIRC. The two hex headed bolts on the flange, and a self tapping screw that's a bit difficult to get at because of the bracket for the bellcrank for the brakes.
Take the hose off under the bonnet, and pull the stub pipe back through.
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Fri Feb 02, 2007 11:06 am

last time i undone quiet a few nuts to take one out tho it was a leaking one like mine aswel but i was tryin to experiment on how to take one out

i coudlnt get the nut undone the one thats hard to get to and then the whole unit wouldnt slide out of the heater maxtrix how long is it i was trying to slide it out towards the passenger door but it wouldnt move
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Mon Feb 05, 2007 1:31 pm

i been offered this one does it look like its going to go soon or would it be ok

Image

Image
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Mon Feb 05, 2007 6:48 pm

can any one help?
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Feb 05, 2007 6:59 pm

Every one I've seen seems to have the small gap between the two halves, if that's what you're worried about.
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Tue Feb 06, 2007 12:07 am

yeh thats what i was worried about if thats how they are then il prob get it

how much are they new to buy from bmw? any idea
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Tue Feb 06, 2007 12:10 am

About £100 IIRC.
Image
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Wed Feb 07, 2007 1:47 pm

going to change the electric heater valve today so i put a piece of garden hole on the bottom pipe on the engine bay and blow out any water and it will come out of the top pipe is this right?
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Feb 07, 2007 2:03 pm

Yep! still may get some spillage when you undo the valve, but not as much. If you flush the matrix with clean water first as well, the spillage will only be clean water.
DJ_B4L
E30 Zone Regular
E30 Zone Regular
Posts: 973
Joined: Sat May 14, 2005 11:00 pm
Location: Kent

Post Wed Feb 07, 2007 2:18 pm

cheers brian will the pressure of a hose pipe be ok to clean the water first in the heater maxtrix and this can be done from the bottom pipe
PIONEER AVIC X1, X1R, X1 BT LATEST SATNAV DISK WITH LATEST MAPS AND ALSO UPDATES FIRMWARE £20 POSTED PM FOR MORE DETAILS

Number plate for sale E30 2 HRD open to serious offers only will suit any E30
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Feb 07, 2007 7:08 pm

Hose must be connected to the bottom pipe. Connect a hose to the top pipe and you risk damaging the heater valve (not that it matters in your case, cause that's what you're replacing).
User avatar
dmc1980
E30 Zone Newbie
E30 Zone Newbie
Posts: 4
Joined: Mon Feb 05, 2007 11:00 pm

Post Tue Feb 13, 2007 6:37 pm

Hi guys, only joined a week or so ago, but have been reading with interest.

Recently bought a 1986 325i sport with mtech1 kit etc.

Got the car completely resprayed there, and while working at it have noticed that the passenger footwell suddenly got very wet after the car was running for a while. Have stripped the heater matrix out and also the heater control valve. What i was wondering is, what is the best way to test them, or can they be tested?

Also, are these parts the correct parts for replacing them?

Heater Matrix
http://www.eurocarparts.com/ecommerce/S ... esults.asp
part number 214110031

Heater control valve
http://www.eurocarparts.com/ecommerce/S ... esults.asp
part number 212110080

Thanks in advance :)
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Feb 13, 2007 7:05 pm

Whenever a fault occurs on a car the correct procedure is to perform tests and identify the faulty part.
Only one of these, if either, will be faulty, so why do you want to change both of them? You should have run the cooling system up to temperature and pressure and looked to see where, if at all, the leak was.
Is the water in the footwell coolant at all? Could well be a water leak from outside, or the scuttle drain blocked!
One thing to make sure of, is that the coolant pressure cap has been replaced under recall.
User avatar
dmc1980
E30 Zone Newbie
E30 Zone Newbie
Posts: 4
Joined: Mon Feb 05, 2007 11:00 pm

Post Tue Feb 13, 2007 10:48 pm

thanks for your answer to my questions. The reason for wanting to replace both of them, its a 1986 car, and while im in there, i might as well :)

I am also certain it is one of them that is at fault, and im almost certain as well that it is the heater control valve. I am also certain that it is coolant water in the floor well :)

SO can you tell me, are they the right parts?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Feb 13, 2007 11:06 pm

dmc1980 wrote: The reason for wanting to replace both of them, its a 1986 car,

SO can you tell me, are they the right parts?
You under estimate the quality and longevity of E30 parts.
I would expect a '86 car to have the aluminium pipe heater, but if it's plastic, then those look like the right parts.
User avatar
dmc1980
E30 Zone Newbie
E30 Zone Newbie
Posts: 4
Joined: Mon Feb 05, 2007 11:00 pm

Post Wed Feb 14, 2007 6:21 pm

thanks for the advice, pressure tested both parts today in work, and the matrix is fine, the heater control valve is knackered, new one will be here tomorrow along with a few other parts.