Cams

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

ed325i
E30 Zone Addict
E30 Zone Addict
Posts: 4146
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Dec 22, 2006 6:37 pm

People always recomend Schrick cam's for BMW's are there anyother cam's that can be used with good results ?

I was looking here at piper/kent cams >> http://www.needforspeed.co.uk/pages/sbv ... le=BM__302
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Fri Dec 22, 2006 8:16 pm

I have a Cat Cams 273 degree in my 2.7, gives excellent results.

Got it from here www.catcams.co.uk about £260.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
ed325i
E30 Zone Addict
E30 Zone Addict
Posts: 4146
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Dec 22, 2006 8:27 pm

Did you use a vernier pulley? would I need one with a 2.5
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Sat Dec 23, 2006 1:40 am

dbilas make cams Ed as long as they are all machined from blanks then i cant see any real difference in them anyone? apart from the material used for the cam
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Sat Dec 23, 2006 2:04 am

dbilas make cams Ed as long as they are all machined from blanks then i cant see any real difference in them anyone? apart from the material used for the cam
And how closely the numbers in the blurb relate to the degrees of lift the valves end up seeing, and what the ramp angles are like.

Catcams are apparently quite good at doing what they say, others aren't supposed to be as reliable.
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
ed325i
E30 Zone Addict
E30 Zone Addict
Posts: 4146
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Dec 23, 2006 10:22 am

Going give cat cams ago if it makes my engine purrrrrrrrrrrr.
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Sat Dec 23, 2006 10:46 am

Piper cams have always been good, ground from new blanks not reprofiled shyte.
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Sat Dec 23, 2006 12:30 pm

Cat cams are ground from new blanks too, kent cams are overpriced scrap IMO.

The Cat cams for the E30 are made from chilled cast iron, the best material for our type of rocker conifiguration.

I bought a vernier pulley but ended up fitting the standard one, the timing was spot on.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
User avatar
scott325i
E30 Zone Newbie
E30 Zone Newbie
Posts: 2
Joined: Wed Dec 27, 2006 11:00 pm

Post Thu Dec 28, 2006 11:32 pm

hi, i have just had a shrick 272/284 fitted in my 325ise 91, havent driven it yet tho!! will let you know how it goes!
ed325i
E30 Zone Addict
E30 Zone Addict
Posts: 4146
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Dec 29, 2006 12:00 pm

Have you had anything alse done or just a cam ?
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Fri Dec 29, 2006 12:03 pm

IV heard that cat cams are also good! Pug 205 boys love them. Piper do cheap regrinds on your old cams and refurd them etc.
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Fri Dec 29, 2006 12:07 pm

weren't this lot in bmw car mag a few months ago with an all singing dancing write up? do they do a 290/290 for an M20?!
DaveD
E30Zone Wiki Specialist
Posts: 5129
Joined: Tue Jan 11, 2005 11:00 pm
Location: Sheffield

Post Fri Dec 29, 2006 3:26 pm

these are the ones they do over 283




1300528
293 / 293°
259 / 259°
12.40 / 12.40mm
3.85 / 3.85mm
custom
MECH: rally & race

1300530
296 / 296°
264 / 264°
12.50 / 12.50mm
4.50 / 4.50mm
custom
MECH: rally & race

1300517
308 / 309°
269 / 269°
12.20 / 12.20mm
5.10 / 5.00mm
custom
MECH: rally & race
User avatar
scott325i
E30 Zone Newbie
E30 Zone Newbie
Posts: 2
Joined: Wed Dec 27, 2006 11:00 pm

Post Fri Jan 05, 2007 11:13 pm

ed325i, ath the mo i've just got cam and boost valve, am planning 6 branch manifold and chip tho before it goes back on the road
M5pilot
E30 Zone Addict
E30 Zone Addict
Posts: 4968
Joined: Sun Jan 30, 2005 11:00 pm
Location: Luton

Post Fri Jan 05, 2007 11:27 pm

Get rid of the boost valve, you don't need it.

Cat cams will be available through the Zone Shop very soon.

Sal
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Fri Jan 05, 2007 11:45 pm

Oz is having a cat cam in his 2.7 thats being built, i'll be interested to see how it goes with this in it
User avatar
gooner1
Out humping Reindeer
Posts: 13280
Joined: Fri Apr 14, 2006 11:00 pm
Location: Northampton.For my sins.

Post Sat Jan 06, 2007 12:52 am

Has anyone fitted a catcam on a 3.5 conversion and if so with what results or recomendations.
Image