icv,tps bad starting..! Brianmoore!!

Need technical Q/A then you're in the right place

Moderator: martauto

toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Wed Jan 03, 2007 8:01 pm

OK,
I recently cleaned out the afm with contact cleaner it seemed to bring moisture out from the circuit board, I let it dry and sparyed it with a little silicone greese.
But still I have bad starting problems.
I did a search on e30zone and found someone else that said When he put his hand under the inlet manifold and wiggled the connection wires to the tps the reves rose. Ok so this is just a loose connection yes?
Because I disconnected the lead from the tps and the car still started so it cant be the tps at fault, right?
I am going through a huge diagnostics opperation with my 1989 325i and have done all the cleaning and changing of heat sensors.
How do you tell if the tps,icv is working properly?
IS THERE ANY WAY THOSE TWO PARTS WOULD GIVE A BAD COLD START?

:cry: [/b]
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Jan 03, 2007 9:24 pm

I think the TPS and ICV are only "concerned" when the engine is running..........

If the TPS is not working properly, it will give a rough idle......same with ICV.
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Wed Jan 03, 2007 9:25 pm

perhaps you could explain what a "bad cold start" is !

explain what happens when you start the car.
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 03, 2007 9:35 pm

Car should start OK with the afm disconnected. Often do this when I forget to reconnect the plug! Just won't accelerate.
Dud TPS will make the car more hesitant to start and idle badly, but it should still start.
First test of a TPS is that it should click faintly just after you move the throttle of its stop, and again at between 1/2 and 2/3 throttle.
Second test is to pull off the plug and put a ohmmeter between pins 1 and 2. Should be short circuit at rest, becoming open circuit as the throttle moves off its stop. Next, put the meter between pins 1 and 3. Should be open circuit at rest, becoming short circuit between 1/2 and 2/3 throttle.
Icv is difficult to test, except for resistance readings between its pins (which I don't have handy), but has nothing to do with starting, although one jammed shut would probably make the engine stall again because of too low an idle speed.
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Wed Jan 03, 2007 10:29 pm

Thanks Brian,
tps clicks just off throttle stop but not between 1/2 and 2/3 throttle.
I cleaned out the tb and icv, tps. Set them all to correct settings.
They were badly out of synic.
However, now the car is taking a lot of cranking to get her going first thing.
Runs fine otherwise.
New zone chip helped for 2 days then probs came back.
Chip is sposed to set idle at 900 but car still idles at 600!

I hesitate to use test meter because I am not sure of where to place to dial to get correct readings :mad:

However I have tested the afm successfully, just need to get my head around how to set tester properly!

Thanks for the advice, I will look again tomorrow.
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Jan 03, 2007 10:31 pm

Have you tried the Temp sensor for the ECU ????
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Wed Jan 03, 2007 10:42 pm

Kam, The blue one? Changed it twice.

Smithy, When I go to start my car from cold first thing in the morning I do not touch the throttle.

The car starts, struggles to climb to idle and stalls.

Turn her over again, she will not start.

Have to hold throttle peddle down to clear petrol then lift foot to half way and eventually she fires up.

Hold the revs around 2000rpm then take my foot of throttle and she idles fine.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 03, 2007 10:43 pm

Tps clicking proves nothing, not clicking proves it's dud. You need to get a meter on it.
Most meters have a continuity buzzer that will do for this test. Short the meter leads together and see if you get a buzzer on one position.
If not, you need a resistance range. These are the ones where the needle goes fully across the dial when you short the leads together.
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Jan 03, 2007 10:45 pm

connector under the inlet manifold maybe ?????
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 03, 2007 10:47 pm

kam-325i wrote:Have you tried the Temp sensor for the ECU ????
The signal from this sensor goes through the injector plug and socket under the inlet manifold. Corrosion in this connector can give the same effect as a dud temp sensor, and give other running effects.
Opened up one of these last weekend, and found that the common supply wire for three injectors was completely rotted through, although apparently still making some kind of contact.
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Jan 03, 2007 10:53 pm

The dodgy connector uner the manifold caused rough running on mine......only found it by chance......

engine was running rougher than dog poo.....i was just fidding around under the manifold, touched something, and it sprung into life.....
it was just loose.....
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Wed Jan 03, 2007 11:24 pm

Thats not the barrel type multi pin connection on the side of the block is it?
If it is I have checked it and it is fine.

I will have a look for the connection you are refering to under the inlet manifold, is it directly under the manifold?

I am confused!
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Jan 03, 2007 11:31 pm

Its on the side of the block, under the inlet manifold.......Seen in centre'ish of pic

Image
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
liam012
E30 Zone Camper
E30 Zone Camper
Posts: 1424
Joined: Sun Aug 28, 2005 11:00 pm

Post Wed Jan 03, 2007 11:33 pm

toughguych:
Are the spark flugs very wet when the engine is cranked? this is a wild guess but you never know - have a look at your afm, is the idle mix screw (located in a small hole just to the side of the black plastic housing) close to the top or over an inch into the bottom of the AFM? - if it is right down at the very bottom try a 5mm alan key and wind it out undoing it bringng it closer to the top of the AFM housing - even half way would do - be absolutely sure that yuuo count how many turns of the alan key you make EXAXTLY for example if you undo it 4 and a quarter turns ad it doesnt fix the starting prob then be suree to wind it back in that ammount
worth a try and it only takes 5 mins.
Image
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Wed Jan 03, 2007 11:37 pm

Dont mess with that screw in the AFM..............end off.........
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Wed Jan 03, 2007 11:40 pm

Kam, thats the one mate.
Will have a good play with it agian.

Liam, I have been adjusting the air/idle screw and at the moment it is 10 turns out.
Will look at it some more and check back in very soon.

Thanks for all your help so far guys, much appriciated.

Lots to think about as usual!
liam012
E30 Zone Camper
E30 Zone Camper
Posts: 1424
Joined: Sun Aug 28, 2005 11:00 pm

Post Wed Jan 03, 2007 11:42 pm

kam: if you turn it 4 turns one way then try to start and then turn it 4 back
how much damage can you do?
all 3 e30's i have bought have had etremely incorrectly set idle mix screws that i have had to bring to the garage and get the CO done (including the one i incorrectly set last night reading U.S autodata numbers!!)
Image
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Thu Jan 04, 2007 12:43 pm

Lunchtime,
Car been sitting for 24 hours.
Turned the afm mixture screw in full and then back two full turns.
Guess what...Car started first time, choke idle speed the lot.
Weather that is down to the screw or me cleaning out the electrics of the afm and them now having time to dry out properly I dont know.
Wont be using the car today so she can rest till tom morning when I will be up early to turn the key.
Lets see........ :?

But the screw should nt affect starting should it?????
liam012
E30 Zone Camper
E30 Zone Camper
Posts: 1424
Joined: Sun Aug 28, 2005 11:00 pm

Post Thu Jan 04, 2007 1:28 pm

no it shouldnt
but if some muppet has wound it right in (like i did by accident) i am guessing what happens is that is just no room for enough air to get in
i started my car this morning and fired up no problem - let it reach hot, turn off then turn on and yep it started again fine
see my thread with my similar prob:
http://www.e30zone.net/modules.php?name ... highlight=
let me know if it stays fixed as i still dont trust mine 100%
yiou should really get the CO set at a garage now
Image
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Thu Jan 04, 2007 7:44 pm

Thanks Liam.
Only my mix screw was set to 10 turns out from full in. I set it while trying to solve rich running prob.
The zone chip seemed to sort alot of it out but it started plying up agian.
I still dont know if my car started well today as a result of me cleaning the afm electrics or turning the mix screw only two turns out from full in.
So I have in fact riched her up.
Time will tell, untill then thanks for all the help I have recived from zone members.
I guess if it is the afm it will f*c^ up again!

Thank God we have this forum!
:wink:
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Jan 06, 2007 10:19 am

Well, its back.
To my horror my car would not start this morning.
I just dont get it.

Back to the drawing board.

When it starts its a little lumpy for few secs but then it is well behaved.

Why oh why does it always go back to being a pig to start... :cry: :cry: :x

What is the key factor that makes it a pig to start but then fine once its running?

Is it the AFM? Remember the car is fine once started and sitting on idle.

How much of a part does the afm play in getting the car started and then when its at idle????
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Jan 06, 2007 10:29 am

toughguych wrote:
How much of a part does the afm play in getting the car started and then when its at idle????
None. Unplug the AFM, and you'll find it'll still start and idle, although it might be slightly upset by the loss of the IAT sensor, which also lives in the AFM housing.
When the TPS switch is at idle AFM information is not used.
Haven't looked back through this thread properly, but have you checked out fuel pressure while you're starting?
The fuel pump receives a lot less voltage when cranking which can cause problems when starting, if it's on its way out.
Re the round injector connector under the manifold: Check the wires under the lower rubber boot, as well as the pins.
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Jan 06, 2007 1:10 pm

Thanks Brian,

Can you tell me what the little box to the bottom left of the AFM is?
Its got a wire that connect to the top of the tb like a chock cable and a vacum pipe that disappers into the passenger side bulk head.
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Jan 06, 2007 1:39 pm

Whats the Automatic choke temperature sensor wiring and where is it?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Jan 06, 2007 2:17 pm

toughguych wrote:Thanks Brian,

Can you tell me what the little box to the bottom left of the AFM is?
Its got a wire that connect to the top of the tb like a chock cable and a vacum pipe that disappers into the passenger side bulk head.
Don't recognise this at all! 89 325 isn't it?
Only thing that comes to mind with small pies and wires is the fuel tank vent valve on emissions equipped cars, but it doesn't really sound like that either.
There's no automatic choke, sensor or wiring on this engine as such. The engine ECU temp sensor is up at the top front of the engine with a blue connector on it. Cold running fuel enrichment is achieved by increasing the duty cycle of the injectors.
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Jan 06, 2007 2:46 pm

Will be back shortly will pic
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Jan 06, 2007 3:57 pm

Will upload pic in very short while.

One thing I did notice was that when I took the blue temp sensor lead off when the car was at op temp The engine revs incresed for 1 second and then returned to same level as when the lead was connected.

Is this normal Brian?
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Jan 06, 2007 4:10 pm

http://rapidshare.com/files/10506769/bay1.JPG

Sorry, dont know how to get a pic on forum.

Is this the the cruse control?

The part in question is the little box in the bottom left hand corner of the pic.
Its got a cable going to the throttle linkage on the top of the tb
suzie650
E30 Zone Regular
E30 Zone Regular
Posts: 460
Joined: Sat Oct 21, 2006 11:00 pm
Location: CH

Post Sat Jan 06, 2007 4:28 pm

Brianmoooore wrote:
toughguych wrote:
How much of a part does the afm play in getting the car started and then when its at idle????
Have you checked out fuel pressure while you're starting?
The fuel pump receives a lot less voltage when cranking which can cause problems when starting, if it's on its way out.
Would be my bet too, especially as an e30 we had in the family went trough a pump every 80'000 km, with similar symptoms.
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Jan 06, 2007 5:28 pm

When all this trouble started 2-3 years ago I took the full pump out of the tank.

I tested it to the extent of examination and applying voltage to check it was working propery.

What other tests should I carry out?

Is there a specific amount of amps etc I need to check for with a meter?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Jan 06, 2007 8:24 pm

toughguych wrote: What other tests should I carry out?
Connect a fuel pressure gauge to the fuel supply line near the fuel rail with a tee piece and a couple of short bits of fuel hose.
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Jan 06, 2007 9:05 pm

Ok, and then?

Like, what am I looking for?

What about the pic?
What do you think it is?
:roll:
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Sat Jan 06, 2007 9:06 pm

There is no picture to see.......
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Sat Jan 06, 2007 9:09 pm

Christmas special-offer: Premium Access 30% Discount! :?
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Jan 06, 2007 9:42 pm

toughguych wrote:
One thing I did notice was that when I took the blue temp sensor lead off when the car was at op temp The engine revs incresed for 1 second and then returned to same level as when the lead was connected.

Is this normal Brian?
If you pull off the blue temp sensor lead, then the ECU will think the engine is stone cold, and go to maximum fuel enrichment. The ICV should still control the idle speed OK, but this should increase by a couple of hundred RPM to the cold idle speed.
Engine should also run very rich and lumpy.