this is by far the worse thing in the world - a squeaking fanbelt....
how do i tighten it, i did it on my old e36, but i dont know how to do the e30?
tightening a fan belt - please help me asap!!!
Moderator: martauto
-
smithy318i
- Engaged to the E30 Zone

- Posts: 5797
- Joined: Thu Apr 28, 2005 11:00 pm
- Location: Tyne & Wear
you need to loosen the top mount of the alternator
then adjust the angle of the alternator to tighten the belt.
then tighten the bolts again.
you can use the handle of a hammer to lever the alternator while you tighten the bolt back up.
then adjust the angle of the alternator to tighten the belt.
then tighten the bolts again.
you can use the handle of a hammer to lever the alternator while you tighten the bolt back up.

-
tregzybmw
- E30 Zone Newbie

- Posts: 209
- Joined: Sat Jul 01, 2006 11:00 pm
- Location: plymouth
ok, so i open the bonnet, where can the bolt(s) be found?
if i dont fix this tonight someone can buy a e30 cab, fsh, 100k, 320i, full leather, graphite grey, 15bbs and 17alpinas available, electric hood for 75p
if i dont fix this tonight someone can buy a e30 cab, fsh, 100k, 320i, full leather, graphite grey, 15bbs and 17alpinas available, electric hood for 75p
-
smithy318i
- Engaged to the E30 Zone

- Posts: 5797
- Joined: Thu Apr 28, 2005 11:00 pm
- Location: Tyne & Wear
the bolt on the top of the alternator mount..
http://www.realoem.com/bmw/showparts.do ... g=12&fg=21
parts 10/11/12
http://www.realoem.com/bmw/showparts.do ... g=12&fg=21
parts 10/11/12

-
Nelly
- Gumbo

- Posts: 4239
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Divorce Central
1x 13mm spanner , 1x 19mm spanner , 1x crowbar(if needed)
Loosen the 13mm top mount + bottom mount slightly, then by turning the 19mm nut-head towards the engine you'll push the alternator away making the belt tighter, once in the right position - tighten up the 13mm top mount whilst holding on pressure to the 19mm.
In most cases on these old BM's now, the teeth on the tensioner might be broken - this is where you can use a crowbar between the alternator and the engine to apply the needed pressure.
Hope this makes sense for you?
Neil.
Loosen the 13mm top mount + bottom mount slightly, then by turning the 19mm nut-head towards the engine you'll push the alternator away making the belt tighter, once in the right position - tighten up the 13mm top mount whilst holding on pressure to the 19mm.
In most cases on these old BM's now, the teeth on the tensioner might be broken - this is where you can use a crowbar between the alternator and the engine to apply the needed pressure.
Hope this makes sense for you?
Neil.
-
tregzybmw
- E30 Zone Newbie

- Posts: 209
- Joined: Sat Jul 01, 2006 11:00 pm
- Location: plymouth
will give it a go in a bit cheers guys, you may have succeeded in lowering my blood pressure
-
d6dph
- Married to the E30 Zone

- Posts: 12435
- Joined: Sun Aug 14, 2005 11:00 pm
- Location: Tiptree. Essex
May make life easier to remove the airbox and AFM to get access to the bolts, Don't think it's needed but may help.

-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Definitely take these off. Only takes a couple of minutes, but don't lose the rubber bit on the bottom when you put it back. I glue them to the airbox.d6dph wrote:May make life easier to remove the airbox and AFM to get access to the bolts, Don't think it's needed but may help.
Damage to the adjuster rack and pinion is caused by slackening the locknut too much.

