NUTS (and bolts), where's this from?

Need technical Q/A then you're in the right place

Moderator: martauto

reddevil
E30 Zone Regular
E30 Zone Regular
Posts: 414
Joined: Mon Jul 04, 2005 11:00 pm
Location: Stockton, Teesside, UK

Post Mon Dec 18, 2006 5:54 pm

Hi Guys, got a call from my wife this morning saying she had found a large bolt on the drive after I'd left for work this morning. I had started my car and left it running for 15 mins before setting off so it had time to defrost, can only guess the bolt fell of then. It was on the drive towards the front of the car and roughly in the middle (if this helps).

The bolt looks new though it was covered in black gunk before I wiped it clean. In the past two weeks I have had a new exhaust rear section fitted (the guy also checked the brakes front/rear), guessing it's not been fitted properly then since it's too new to be much older?. The car seems to be running fine though I have taken it easy. It's pitch black here and foggy so cannot get under the car, just really wanting to know that it's safe to drive back to the garage tomorrow night rather than do any damage to the car or my new exhaust.

Here are some piccy's next to a pound coin (for scale):


Image
Image

Thanks for any advice.

Red Devil
Ps. The bolt is shiney silver though it may look dull in the pictures.
1991 (H) 318iS Diamond Black, M-tech II spoiler.
K&N Panel filter-Viper2 chip-Zone BBTB
XBOX LIVE - reddevil1976
Richy325iTouring
E30 Zone Addict
E30 Zone Addict
Posts: 3490
Joined: Sun Jan 09, 2005 11:00 pm
Location: Newport SouthWales

Post Mon Dec 18, 2006 5:56 pm

check the clamps on the exhaust about half way down the car

probably from there
Image
User avatar
dilo_attax
E30 Zone Newbie
E30 Zone Newbie
Posts: 213
Joined: Mon Apr 24, 2006 11:00 pm
Location: the moon

Post Mon Dec 18, 2006 5:57 pm

can you hear any rattles?
Image
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Mon Dec 18, 2006 6:01 pm

is it about 50mm long ?

Looks kinda "gearboxy"....
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Mon Dec 18, 2006 6:04 pm

Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
320Touring
E30 Zone Team Member
E30 Zone Team Member
Posts: 12316
Joined: Fri Feb 11, 2005 11:00 pm
Location: Glasgow (Scotland)

Post Mon Dec 18, 2006 6:15 pm

kam-325i wrote:is it about 50mm long ?

Looks kinda "gearboxy"....
amen- looks like one of the 4 that go vertically to hold on the bellhousing at the front of the gearbox (the section that covers the rear of the sump on an m20)
The big Unit Parts Clear out Make me an offer on parts!
http://www.e30zone.net/modules.php?name ... 81#2766881
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Mon Dec 18, 2006 6:18 pm

Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
liam012
E30 Zone Camper
E30 Zone Camper
Posts: 1424
Joined: Sun Aug 28, 2005 11:00 pm

Post Mon Dec 18, 2006 6:21 pm

could it be a rear arb drop link bracket bolt?
or this is way out left now so brace urself)a subframe bolt? the one that goes up thrpugh the bush into the body?- although maybe a bit short now i lookk closer.
Image
Richy325iTouring
E30 Zone Addict
E30 Zone Addict
Posts: 3490
Joined: Sun Jan 09, 2005 11:00 pm
Location: Newport SouthWales

Post Mon Dec 18, 2006 6:21 pm

i def say exhaust

if thats just been changed
i could be wrong but have had these drop off before
Image
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Mon Dec 18, 2006 6:24 pm

I cant really see it being from the exhaust, as i dont think the tread would be coverd in that black oily gunk, it would be getting hot, have a nut on it, so the end of the thread would show signs of where the nut has been.
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
Richy325iTouring
E30 Zone Addict
E30 Zone Addict
Posts: 3490
Joined: Sun Jan 09, 2005 11:00 pm
Location: Newport SouthWales

Post Mon Dec 18, 2006 6:26 pm

could have a point there karm
Image
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Mon Dec 18, 2006 6:27 pm

I think it might be number 5 on this list (it holds the center mount of the exhaust to the gearbox)


http://www.realoem.com/bmw/showparts.do ... g=18&fg=10
Image
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Mon Dec 18, 2006 6:29 pm

smithy318i wrote:I think it might be number 8 on this list (it holds the center mount of the exhaust to the gearbox)


http://www.realoem.com/bmw/showparts.do ... g=18&fg=10
Thats a good one aswell, as when i replaced the bracket on mine, the 2 bolts where coverd in black gunk from the gearbox
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
Nelly
Gumbo
Gumbo
Posts: 4239
Joined: Mon Jan 10, 2005 11:00 pm
Location: Divorce Central

Post Mon Dec 18, 2006 6:33 pm

Front Subframe bolt??
Image

"I F**KING LOVE YOU GUMBO"
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Mon Dec 18, 2006 6:34 pm

Nelly wrote:Front Subframe bolt??
Number 3 on here

http://www.realoem.com/bmw/showparts.do ... g=31&fg=05
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
Nelly
Gumbo
Gumbo
Posts: 4239
Joined: Mon Jan 10, 2005 11:00 pm
Location: Divorce Central

Post Mon Dec 18, 2006 6:35 pm

Number 3;

Image
Image

"I F**KING LOVE YOU GUMBO"
Nelly
Gumbo
Gumbo
Posts: 4239
Joined: Mon Jan 10, 2005 11:00 pm
Location: Divorce Central

Post Mon Dec 18, 2006 6:36 pm

Argh!! - too slow.
Image

"I F**KING LOVE YOU GUMBO"
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Mon Dec 18, 2006 6:37 pm

how long is it?

the bolts which hold the center exhaust mount (on my car) are 55mm and 60mm with a 13mm head
Image
Martinaston
E30 Zone Addict
E30 Zone Addict
Posts: 3749
Joined: Mon Mar 14, 2005 11:00 pm
Location: London

Post Mon Dec 18, 2006 6:39 pm

Gearbox bolts are a lot bigger and the subframe bolt goes down through the car so its just a nut underneath.
From the size of it, its either from the new exhaust clamp (although they should be U bolt clamps and wouldn't be covered in greese as it would burn off). The clamp between the front and centre section uses nuts and bolts but again wouldn't be covered in gunk.
The only other bolts of that size i can think of are the ones used in the steering coupling 8O
There is NO nucleus.
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Mon Dec 18, 2006 6:41 pm

does the winner get a prize?
Image
SPADGE
Married to the E30 Zone
Married to the E30 Zone
Posts: 7373
Joined: Wed Aug 09, 2006 11:00 pm
Location: Milton Keynes, Bucks

Post Mon Dec 18, 2006 6:42 pm

That bolt is far too big to be anything to do with the exhaust!
I'd guess at what has been said already the bottom of the front part of the bellhousing that is detachable. It may not be from underneath though and so could be a number of things under the bonnet.
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
drewjak
E30 Zone Regular
E30 Zone Regular
Posts: 410
Joined: Sat May 20, 2006 11:00 pm
Location: cumbria, england

Post Mon Dec 18, 2006 6:53 pm

probly sounds daft? i know the bumper bolts are a torx fitting, but could some one have put a diffrent one in? mine seem to have a habbit of comin loose and falling out sometimes????????????
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Mon Dec 18, 2006 7:00 pm

drewjak wrote:probly sounds daft? i know the bumper bolts are a torx fitting, but could some one have put a diffrent one in? mine seem to have a habbit of comin loose and falling out sometimes????????????
Not too daft. but not the right bolt, bumper bolts are massive compared to the one at the top of the page.
Image
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Mon Dec 18, 2006 7:03 pm

how many other people are holding a £1 coin and a bolt and against thier screen ? (or is it just me)
Image
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Mon Dec 18, 2006 7:17 pm

Cant make my mind up if its an 8 or 10mm bolt :?
Looks to be between 80 and 100mm long.

Only thing I can think of likely to fall on the floor is the steering rack mounting bolts, they have a 15mm hexagon and should be put in from the top with the nut underneath but maybe if the car has had rack work/replacement they have been put back the wrong way around.
Bob_S
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5412
Joined: Sat Jun 11, 2005 11:00 pm
Location: chester, cheshire

Post Mon Dec 18, 2006 7:32 pm

i'm with dan.. it might be a 'rack bolt?
Bollocks to this 24v scrap!
reddevil
E30 Zone Regular
E30 Zone Regular
Posts: 414
Joined: Mon Jul 04, 2005 11:00 pm
Location: Stockton, Teesside, UK

Post Mon Dec 18, 2006 8:02 pm

Ok Guys, have some measurements for you, here they are:
Image
Image

Have just looked under the car, the zorst bolts all seem to be in place (from what I can see), I can see the top of the gearbox if I put my head on the scuttle panel and I think we MAY have a winner, I can see the top of the bell housing between the brake servo bit and the top of the block, if I stick my finger in there there is room for the tip. God knows if I am looking in the right place though.

The bolt was covered in black gunk, oil I guess and yes it is in the thread. The bolt says KX 42-70. No signs of wear on the bolt though and when I look at other bolts they all seem to be aged, whereas this one seems pretty new?.

Keep coming with the ideas.
1991 (H) 318iS Diamond Black, M-tech II spoiler.
K&N Panel filter-Viper2 chip-Zone BBTB
XBOX LIVE - reddevil1976
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Mon Dec 18, 2006 8:19 pm

Ok so its 70mm, I was close though :)

13mm hex and 8mm shank
Looks as though it has had a liberal coating of engine oil to stay so nice and new, like most M20 bolts have winkeye
drewjak
E30 Zone Regular
E30 Zone Regular
Posts: 410
Joined: Sat May 20, 2006 11:00 pm
Location: cumbria, england

Post Mon Dec 18, 2006 8:31 pm

smithy318i wrote:
drewjak wrote:probly sounds daft? i know the bumper bolts are a torx fitting, but could some one have put a diffrent one in? mine seem to have a habbit of comin loose and falling out sometimes????????????
Not too daft. but not the right bolt, bumper bolts are massive compared to the one at the top of the page.
very true i obviously wasnt takin enough notice of the £ coin, noe ive looked again its not to big is it :o:
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Mon Dec 18, 2006 8:33 pm

Only bolt I can think of that is so long and 8mm is the alternator mount bolt :?

Are you sure its off your car? :)
SPADGE
Married to the E30 Zone
Married to the E30 Zone
Posts: 7373
Joined: Wed Aug 09, 2006 11:00 pm
Location: Milton Keynes, Bucks

Post Mon Dec 18, 2006 8:35 pm

There is a bolt very similar to that in the bottom of the alternator which could have fallen out?
There isn't enough thread on the bolt for what i suggested earlier.
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Mon Dec 18, 2006 8:35 pm

Hmm difficult to track down but........

I'm thinking lower sump extension section,down by the front lower bellhousing ,has a habit of collecting oil, would be easy to spot, go to your local fast fit and get a quote for a new 'zaust( you've no intension of buying ) have a quick looky whilst in the air.

good game :lol:
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
reddevil
E30 Zone Regular
E30 Zone Regular
Posts: 414
Joined: Mon Jul 04, 2005 11:00 pm
Location: Stockton, Teesside, UK

Post Mon Dec 18, 2006 8:39 pm

DanThe wrote:Are you sure its off your car? :)
I am guessing yes but God knows.

Right, just been out and turned the car round too see if I could see the nut. When moving the car (which was freezing cold if it matters) and turning the steering wheel (more than quarter turn) the car made a grumble, more like a vibration or groan, possibly grinding. Sorry I can't be more specific but God only knows. You could hear it from inside the car with the engine running and it's NOT the usual squeek that I get from a full lock from the power steering, defiantly not.

So it's a nut on the floor, a graning on the steering (grinding rather than power steering squeek).

HELP, I laid on the floor and looked underneath but could not see anything obvious missing or loose.

Red D
1991 (H) 318iS Diamond Black, M-tech II spoiler.
K&N Panel filter-Viper2 chip-Zone BBTB
XBOX LIVE - reddevil1976
User avatar
victoruk2
E30 Zone Newbie
E30 Zone Newbie
Posts: 20
Joined: Fri Dec 15, 2006 11:00 pm
Location: Middlesbrough Cleveland

Post Mon Dec 18, 2006 8:46 pm

The shiney bit near the head says it has been loose for a while. The markings on the head says high tensile, so I'm thinking bell housing to engine. Top one are allways dirty, and it could have fallen out when you were de-frosting the car.
reddevil
E30 Zone Regular
E30 Zone Regular
Posts: 414
Joined: Mon Jul 04, 2005 11:00 pm
Location: Stockton, Teesside, UK

Post Mon Dec 18, 2006 8:51 pm

victoruk2 wrote:The shiney bit near the head says it has been loose for a while. The markings on the head says high tensile, so I'm thinking bell housing to engine. Top one are allways dirty, and it could have fallen out when you were de-frosting the car.
Would that give me the noise through the steering though?, I know little to nothing about cars so am looking for pointers, also need to know if it's safe to limp it to a garage tomorrow morning?.

Red D
1991 (H) 318iS Diamond Black, M-tech II spoiler.
K&N Panel filter-Viper2 chip-Zone BBTB
XBOX LIVE - reddevil1976