Anyone ditched their ABS?

Need technical Q/A then you're in the right place

Moderator: martauto

old_skool
E30 Zone Team Member
E30 Zone Team Member
Posts: 3405
Joined: Fri Sep 01, 2006 11:00 pm
Location: Glossersure

Post Fri Dec 15, 2006 5:48 pm

Has anyone here taken out their ABS system?

To be honest I've never got on with it in any car I have ever owned and I'm fully aware that for a 90 year old granny it might be great for when they jump on the brakes in a panic but for me I'd rather go for non ABS, especially for occasional track use etc.

I see the master cylinder has two pipes that go into the ABS servo (front and rear brakes), these then distribute to rear/front of the servo. From there the servo splits the front feed to both front calipers individually whilst the back are combined on the same circuit. Hence if one rear wheel locks up then brake force will be omitted from both wheels.

As far as I am aware the ABS servo serves to simply interrupt the brake circuit and doesn't provide any brake boost. Firstly is this correct and secondly will this interfere with brake force distribution if I were to operate the calipers directly from the master cylinder?

All input welcome :D
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Fri Dec 15, 2006 5:56 pm

All correct and it wont interfere with brake force distribution.

Andrew
old_skool
E30 Zone Team Member
E30 Zone Team Member
Posts: 3405
Joined: Fri Sep 01, 2006 11:00 pm
Location: Glossersure

Post Fri Dec 15, 2006 6:10 pm

All correct and it wont interfere with brake force distribution.
Thanks Andrew,

In this case does that mean that the brake distribution from the master cylinder is equal - hence the need for the inline pressure regulator. I assume it is an inline pressure regulator beneath the servo in the rear brake line?

Off topic, which (exact) servo do I need for my S50 (which I now have on a pallet!) to avoid cutting of the plenum altogether?
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Fri Dec 15, 2006 6:54 pm

The golf servo can be used I belive, not having an ABS pump will be handy when it comes to plumbing in an air filter 8)
old_skool
E30 Zone Team Member
E30 Zone Team Member
Posts: 3405
Joined: Fri Sep 01, 2006 11:00 pm
Location: Glossersure

Post Fri Dec 15, 2006 7:16 pm

not having an ABS pump will be handy when it comes to plumbing in an air filter
Why yes it would :idea:

Cheers DanThe,

ANy ideas which Golf servo, I know 'nowt about golfs?
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Fri Dec 15, 2006 7:34 pm

old_skool_2002 wrote: All input welcome :D
and if someone can add a diagram showing which pipes connect to which after removing the pump that would be very helpful.mine is non opperational but still fitted and i find braking better as the abs seemed to cut in to early :wink:
old_skool
E30 Zone Team Member
E30 Zone Team Member
Posts: 3405
Joined: Fri Sep 01, 2006 11:00 pm
Location: Glossersure

Post Fri Dec 15, 2006 7:51 pm

and if someone can add a diagram showing which pipes connect to which after removing the pump that would be very helpful.mine is non opperational but still fitted and i find braking better as the abs seemed to cut in to early
No problem, quite straightforward really, i'll post a "blue Peter" sketch tomorrow :lol:

Also considering a brake isolation/bias valve "In car" for the rear brakes, for obvious reasons. Any idea if there is a setup that can be used?
keskinKT4
E30 Zone Newbie
E30 Zone Newbie
Posts: 72
Joined: Thu May 11, 2006 11:00 pm
Location: Limerick, Ireland.

Post Sat Dec 16, 2006 1:03 pm

Remove the abs relay and then you have a non abs thats what i do for track days .
zaust
Zone day release
Posts: 13007
Joined: Sun Jan 09, 2005 11:00 pm
Location: Somewhere in Hertfordshire , or press Ctrl + W

Post Sat Dec 16, 2006 1:07 pm

I have taken the power wire to the abs ecu and put a switch in line so i can choose as and when i want..


winkeye winkeye winkeye
M30 Tech 1 Touring on gas.
Image
keskinKT4
E30 Zone Newbie
E30 Zone Newbie
Posts: 72
Joined: Thu May 11, 2006 11:00 pm
Location: Limerick, Ireland.

Post Sat Dec 16, 2006 1:09 pm

i've seen a fiat punto servo used a few time for your conversion
jmc330i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6621
Joined: Mon Jan 10, 2005 11:00 pm
Location: Somerset

Post Sat Dec 16, 2006 1:12 pm

old_skool_2002 wrote: ANy ideas which Golf servo, I know 'nowt about golfs?
Mk1 GTi or Mk2 1.3.
They are the same size, but fitting them is slightly different. You will need to cut the plenum if you are keeping the brake servo though. You could move the servo over a little (drill new holes in the bulkhead) which might help reduce the amount to be cut.

The Mk1 1.3 servo is smaller again, but I didnt think it would be suitable for an E30 with near on 300bhp. I did have one, but didnt offer it up with the S50 plenum in place because Id already decided to go with the Mk1 GTi servo.
James
'91 325i Sport
'93 318i touring 16v
bigdek
E30 Zone Camper
E30 Zone Camper
Posts: 1115
Joined: Thu Feb 10, 2005 11:00 pm
Location: Fife Scotland

Post Mon Dec 18, 2006 7:37 pm

would it fail mot for being removed ?

mine will be in the way for my brake servo on my m60 conversion.

if i can just toss it in the bin its history.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Mon Dec 18, 2006 7:48 pm

You can remove the servo completley and it will still pass the MOT.
You would just have to press the pedal harder :)

Would be a good idea to modify the pedal so the point of leverage is higher up the bulkhead, so you have a longer pedal.

With some work you could get the feel quite nice, braided hoses etc, I would hang on to the ABS though if you go the servoless route as this type of system tends to be 'all or nothing' in an emergency which can scare the shit out of ya :)
old_skool
E30 Zone Team Member
E30 Zone Team Member
Posts: 3405
Joined: Fri Sep 01, 2006 11:00 pm
Location: Glossersure

Post Mon Dec 18, 2006 9:36 pm

Cheers Dan,

Too late, ABS is history. Still going to use a servo but I'm going to go the hard way and relocate a new servo approx 36mm over. Need to locate a servo that's fit for the job.

Hopefully I can avoid cutting the plenum and still retain the original look :cool: Also going to install a rear brake cut off valve for future use.

Got the rest of the week off so it's time to play. Still have a lot of prep work until I get that far. These E30's need TRC when it comes to a bare shell strip out and it's taking longer than I anticipated 8O