Went to replace the master and slave cylinders on my iS today. Turns out the hydraulic pipe from the master to the slave was on it's last legs, now it's sheared clean through.
Anyone know how much it is likely to cost to replace the pipe?
Clutch hyrdaulic pipe broken.
Moderator: martauto
-
MrDazzle
- E30 Zone Regular

- Posts: 451
- Joined: Fri Oct 21, 2005 11:00 pm
- Location: On the path to the dark side
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The metal pipe? (I've never seen a rusty one), or the flexible?
Either is only a few pounds to buy, or less than £1s worth of materials if you make up your own with cupro-nickel pipe. (Easier to get the tight bend out of the master cylinder).
Either is only a few pounds to buy, or less than £1s worth of materials if you make up your own with cupro-nickel pipe. (Easier to get the tight bend out of the master cylinder).
-
MrDazzle
- E30 Zone Regular

- Posts: 451
- Joined: Fri Oct 21, 2005 11:00 pm
- Location: On the path to the dark side
Metal pipe....
Nut going onto the master cylinder was all chewed to hell, the pipe had a kink/crack in it about 1cm from the master cylinder. Now it's got a split all the way through it, so it's f*cked. Need the car sharpish, so was wondering how much it'd be for a dealer to fix, bearing in mind I have the master and slave already.
Nut going onto the master cylinder was all chewed to hell, the pipe had a kink/crack in it about 1cm from the master cylinder. Now it's got a split all the way through it, so it's f*cked. Need the car sharpish, so was wondering how much it'd be for a dealer to fix, bearing in mind I have the master and slave already.
-
SPADGE
- Married to the E30 Zone

- Posts: 7373
- Joined: Wed Aug 09, 2006 11:00 pm
- Location: Milton Keynes, Bucks
Sounds like someone in the past has tried to split the flexi and hard line without holding the other to stop it twisting!
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
-
SPADGE
- Married to the E30 Zone

- Posts: 7373
- Joined: Wed Aug 09, 2006 11:00 pm
- Location: Milton Keynes, Bucks
Actually ignore the above i was thinking the crack was at the slave end lol 
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
If you're already geared up to change the master and slave, it's only a tiny bit of extra work to change the metal pipe. Just the joint to the flexi to undo.
-
MrDazzle
- E30 Zone Regular

- Posts: 451
- Joined: Fri Oct 21, 2005 11:00 pm
- Location: On the path to the dark side
CanI buy the pipe already made up?
What about the nut that goes at the master end, is that included?
What about the nut that goes at the master end, is that included?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Yes and yes, but it comes straight.MrDazzle wrote:CanI buy the pipe already made up?
What about the nut that goes at the master end, is that included?
